• Tribology and Lubricants
• /
• 제24권2호
• /
• pp.55-62
• /
• 2008

In recently designed diesel engines, the running conditions for piston pin bearings have become very severe due to combustion pressure and temperature increase. In this paper, it will be investigated the tendency of piston pin rotating motion by calculating the friction coefficient at piston pin bearings, the oil film thickness and the frictional torques induced by hydrodynamic shear stress. Finally, the pressure distributions on the oil film of piston pin bearings will be found by two-dimensional lubrication analysis in order to help the optimum design of the bearings of piston pin. Specially, it is investigated how the changes in combustion pressure at exhaust and intake stroke and the pressure-viscosity index effect on the film pressure distribution.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제33회 춘계학술대회 개최
• /
• pp.149-155
• /
• 2001

New semi-fluorinated polyol esters were synthesized by condensation reaction of polyols (NPG and TMP) and carboxylic acids such as 2-ethylhexanoic acid, stearic acid and perfluorooctanoic acid. The structures of polyol esters were confirmed by FT-IR and H-NMR etc. And, the fluorinated polyol esters were insoluble in several oils, however, the semi-fluorinated polyol esters were soluble in several oils depended on the structure of polyol esters. The physical properties such as 4-ball wear property and extreme-pressure (EP) properties were characterized by measuring wear scar diameter through ASTM D2266 and by determining the load-carrying through ASTM D2783 method, respectively. As the results, wear scar diameters of oils in which the semi-fluorinated polyol esters were added were not changed compared to those of not added oils. While extreme-pressure properties remarkably Increased with fluorine contents of the esters depended on the structure of acid moiety and polyol moiety. Also, the extreme-pressure property of semi-fluorinated NPG polyol ester in gasoline engine oil was better than that of commercial Teflon coating additive.

• 한국수소및신에너지학회논문집
• /
• 제27권1호
• /
• pp.114-120
• /
• 2016

This paper describes generating efficiency characteristics of the double acting Stirling engine/generator for domestic small-scale CHP (Combined Heat and Power) system. In small distributed generation applications, Stirling engine has competition from fuel cell, microturbine and etc. In order to be economical in the applications, a long life with minimum maintenance is generally required. Free piston Stirling engine (FPSE) has no crank and rotating parts to generate lateral forces and require lubrication. Double acting Stirling engine/generator has one displacer and two power piston which are supported by flexure springs. Two power pistons oscillate with symmetric displacement and are connected with moving magnet type linear generators for power generation from PV work. In experiments, 1 kW class double acting free piston Stirling engine/generator is fabricated and tested. Heat is supplied to hot end of engine by the combustion of natural gas and converted to electric power by linear generators which are assembled with power pistons. The electric parameters such as voltage, current and phase are measured with for variable flow rate of fuel gas. Especially, generating efficiency of FPSE is measured with three different measurement methods. Generating efficiency of the double acting Stirling engine/alternator is about 24%.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2002년도 proceedings of the second asia international conference on tribology
• /
• pp.407-408
• /
• 2002

This paper presents a split cooling system for a new inline 4-cylinder automotive engine. The split cooling system circulates coolant to the cylinder head and cylinder block separately. The coolant flow in the cylinder block is controlled by a $2^{nd}$ Thermostat installed at the outlet of cylinder block. The $2^{nd}$ thermostat closes when the coolant temperature is low. And this makes the coolant flow in cylinder block nearly stagnant, thereby reducing the coolant-side heat transfer coefficient and raising cylinder bore temperature. The $2^{nd}$ thermostat starts to open when the coolant temperature reaches a specified temperature. The test results on engine dynamometer show improved fuel economy and lower exhaust emission which result from the decrease in friction works and cooling loss. Also, several vehicle tests, with application of the new engine have been performed. Fuel economy improvement of 0.5{\sim}2.0%$ yields from different test modes and details are discussed in this paper.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1993년도 춘계학술대회 및 공장견학
• /
• pp.39-53
• /
• 1993

The minimum oil film thickness(MOFT) in the connecting-rod bering of a 1.5 liter, L-4, gasoline engine is measured up to 5500 rpm and calculated to study the dynamically loaded engine bearing. Short bearing approximation and Mobility method are used for theoretical analysis of oil film charactrtistics. And cylinder pressure, crank-pin surface temperature and bearing tenp ture are measured as the input data of theoretical analysis. The MOFT are measured by the total capacitance method(TCM). To improve the reliability of the test results, a reasonable detmuuination method of bearing clearance is introduced and used, and the effects of cavitation and aeration on the test results are neglected. The crankshaft is grounded by means of a slip ring. A scissor type linkage system was developed to measure the MOFT and bearing temperature. The effects of engine speed, load and oil viscosity on the measured and calculated minimum oil film thicknesses are investigated at 1500 to 5500 rpm. From the comparison between the measured and calculated MOFT, it is found that a qualitative similarity exists between them, but in all cases, the measured MOFT are smaller than those calculated.

• Tribology and Lubricants
• /
• 제11권5호
• /
• pp.162-171
• /
• 1995

The application of reciprocating engine crankshaft bearings is of particular importance and interest among the plain bearing, not only because the sheer volume of intemal combustion engines now produced, but because the severe operating conditions they are subjected to. Demands for better performances of crankshaft bearings have provide an important impetus in the development of bearings and bearing materials. As engine design progresses toward higher outpt and higher efficiency, crankshaft bearings must perform under more seveve operating conditions. Higher load, temperature, and speed as well as lower viscosity oil are applied to the bearing sysem, resulting in a smaller minimum oil film thickness. This means more solid-solid contact between the shaft and bearing, and the bearing is exposed to more danger of seizure. Some engines may experience bearing seizure problems. However, understanding about the seizure behavior and mechanism is far from being enough. Seizure resistance of a bearing-shaft system will be affected by the properties of the shaft and bearing, especially their materials and surface texture. Commonly used engine bearing materials include Al-Pb-Si, Al-Sn-Si, Al-Sn, and Cu-Pb with Pb-Sn-Cu overlay. These materials have very different properties. They showed different behaviors dering seizure tests and seizure may occur with different mechanism for different bearing material. Shaft materials also affect the seizure resistance of the system. Surface texture of the bearing and shaft have apparent effects on the lubrication and solid-solid contact pattern, and therefore will affect the seizure behavior of the system. Bearings and shafts which are made of different materials and have different surface textures have been tested and analyzed. Their effects on seizure resistance are discussed and possible seizure mechanisms for different beatings are presented in this paper.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.3026-3031
• /
• 2008

In conventional closed-loop crankcase ventilation systems, the lubrication oil had to be re-circulated to the intake manifold, in the form of oil mist mixed with the blow-by gas. This blow-by gas containing the engine lubricant oil affects on the engine problems and the exhaust emissions. A high-efficient oil separator is required to minimize consumption of engine oil and reduce harmful emissions. In the conventional oil separator of CI engines, it has good oil separation performance even though separator design is simple, due to lots of the blow-by gas. As the emission regulation becomes severe, the oil separator for SI engines is also required. But in SI engines, separator design should be optimized, due to small size of oil particles and little amount of blow-by gas. In this study, oil separation performance classified by diameter of oil mist in cylinder head cover internal model which has three cyclones and two baffle plates for SI engine is calculated with CFD methodology.

• 한국산학기술학회논문지
• /
• 제11권9호
• /
• pp.3119-3124
• /
• 2010

본 논문은 엔진 베어링에서 크랭크샤프트의 경사도를 고려했을 때와 고려하지 않았을 때 유막 동적거동을 컴퓨터 시뮬레이션을 이용하여 해석하였다. 본 해석은 탄성유체윤활 이론을 바탕으로 하여 최소유막의 동적특성을 수치적으로 해석하였다. 유막설계에 매우 중요한 인자인 크랭크샤프트 경사도를 고려하기 위하여 크랭크샤프트와 엔진베어링을 탄성체로 모델링 하였다. 유막거동해석을 위한 경계조건으로는 엔진 베어링에서 발생하는 비선형 구속력과 굽힘 모멘트를 고려하였고 이에 따른 크랭크샤프트의 경사도 영향을 고려함으로써 좀 더 실제 현상과 유사한 모델링을 수행하였다. 해석결과 엔진 베어링의 성능에 가장 큰 영향을 미치는 최소유막두께가 크랭크샤프트의 경사도를 고려하지 않았을 때보다 고려하였을 때 16%에서 24%정도 감소하는 것을 알 수 있었다. 또한, 해석결과에서와 같이 크랭크샤프트 경사도 증가는 최소유막두께의 감소를 유발하고 이에 따른 베어링 파손을 예측할 수 있었다. 따라서 본 논문의 해석결과가 자동차 엔진 베어링 설계 시 매우 유용한 자료로 사용될 것으로 사료된다.

• 한국가스학회지
• /
• 제25권4호
• /
• pp.27-35
• /
• 2021

최근 "전력 예비율" 급감에 대한 해결책으로 양방향 송배전이 가능한 마이크로 그리드로 전환되고 있다. 마이크로 그리드는 소규모 분산전원과 부하로 구성되는데, 분산전원의 대표적인 기술로 가정·건물에 적용하는 소형 열병합 발전시스템이 있다. 본 연구에서 가스 소비량 232.6kW(20만 kcal/h) 이내의 소형 가스엔진 발전시스템의 안전기준을 도출하고 발전 시스템, 냉각시스템, 윤활 시스템, 배기 시스템으로 구분하여 안전기준(안)을 개발하였다. 발전시스템의 경우 필터를 설치하고 가스 누출 및 엔진 회전수나 출력에 이상이 발생할 경우 이를 감지하여 시스템이 정지하도록 하였고, 냉각시스템은 냉각수 부족이나 과열이 발생할 경우 시스템이 정지하도록 규정하였다. 윤활 시스템은 윤활유의 압력과 온도를 모니터링 하고 이상이 발생할 경우 시스템을 정지하도록 하고, 배기 시스템은 국내·외 기준과 부합하여 배기가스 배출 농도 규제 값을 지정하였다. 본 연구 결과를 통해 가스엔진 발전시스템의 안전성을 향상시키고 제품 확산·보급에 이바지할 수 있다고 판단한다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2000년도 제31회 춘계학술대회
• /
• pp.219-226
• /
• 2000

Frictional performance of ring pack in internal engine is investigated by varying spatial dimensions of ring pack and operating speed. This investigation is performed with commercial software by Ricardo Consultant Engineers, Inc. which is now in wofdwide use in automobile industries. Among the ring performances, blow-by rate, axial ring motions and frictional behaviors of top and second rings are studies in our work.