• Journal of Electrical Engineering and Technology
• /
• v.10 no.3
• /
• pp.1363-1369
• /
• 2015

The frequency of a power system should be maintained within the allowed limits for stable operation. When a disturbance such as generator tripping occurs in a power system, the frequency is recovered to the nominal value through the inertial, primary, and secondary responses of the operating synchronous generators (SGs). However, for a power system with high wind penetration, the system inertia will decrease significantly because wind generators (WGs) are operating decoupled from the power system. This paper proposes a dynamic droop-based inertial control for a WG. The proposed inertial control determines the dynamic droop depending on the rate of change of frequency (ROCOF). At the initial period of a disturbance, where the ROCOF is large, the droop is set to be small to release a large amount of the kinetic energy (KE) and thus the frequency nadir can be increased significantly. However, as times goes on, the ROCOF will decrease and thus the droop is set to be large to prevent over-deceleration of the rotor speed of a WG. The performance of the proposed inertial control was investigated in a model system, which includes a 200 MW wind power plant (WPP) and five SGs using an EMTP-RV simulator. The test results indicate that the proposed scheme improves the frequency nadir significantly by releasing a large amount of the KE during the initial period of a disturbance.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.8
• /
• pp.767-773
• /
• 2010

In recent years, there has been considerable concern over the release of methyl tert-butyl ether (MTBE), a gasoline additive, into the aquifers used as potable water sources. MTBE readily dissolves in water and has entered the environment via gasoline spills and leaking storage tanks. In this study air stripping and ozonation of MTBE in aqueous solution were performed in a laboratory scale batch reacter. The mass transfer rate (N) was evaluated and a values about $1.24{\times}10^{-6}\;mol{\cdot}sec^{-1}$ was found. In the ozonation of MTBE a 8.3% decrease of the COD and a 6.5% decrease of the TOC lead to BOD/COD = 0.03. The peudo first-order rate constants of the ozonation of MTBE was $3.75{\times}10^{-5}\;sec^{-1}$. The resulting Ea of 4.80 kcal；mol-1 was observed for molecular ozone reactions.

• Journal of Radiation Protection and Research
• /
• v.45 no.4
• /
• pp.154-162
• /
• 2020

Background: Several studies have reported that wild mushrooms contain high amounts of radioactive cesium (137Cs). After the Fukushima Daiichi Nuclear Power Plant Accident, a significantly high concentration of 137Cs has been detected in wild mushrooms, and their consumption may be the cause of the chronic internal exposure of local consumers to radioactivity. Therefore, an accurate evaluation of the internal radioactivity resulting from mushroom ingestion is needed. Materials and Methods: The 137Cs elution rate through the cooking and digestion stages was evaluated using in vitro experiments. The edible mushroom Pleurotus djamor was taken as a sample for the experiments. The mushrooms were cultivated onto solid media containing 137Cs. We evaluated the internal dose based on the actual conditions using the elution rate data. For various cooking methods, the results were compared with those of other wild edible mushrooms. Results and Discussion: From the elution experiment through cooking, we proved that 25%-55% of the 137Cs in the mushrooms was released during soaking, boiling, or frying. The results of a simulated digestion experiment after cooking revealed that almost all the 137Cs in the ingested mushrooms eluted in the digestive juice, regardless of the cooking method. The committed effective dose was reduced by 20%-75% when considering the dissolution through the cooking process. Conclusion: We found that cooking lowers 137Cs concentration in mushrooms, therefore reducing the amount of radioactivity intake. Besides, since there were differences between mushroom types, we demonstrated that the internal exposure dose should be evaluated in detail considering the release of 137Cs during the cooking stages.

• Journal of Radiation Protection and Research
• /
• v.24 no.2
• /
• pp.109-120
• /
• 1999

Residual radiation and radioactivity level in TRIGA Mark-II, III research reactors and facilities at the KAERI Seoul site, which are to be decommissioned, have been measured, analyzed and evaluated to know the current status of radiation and radioactivity level and to establish and to provide the technical requirements for the safe decommissioning of the facilities which shall be applied in minimizing the radiation exposure for workers and in preventing the release of the radioactive materials to the environment. Radiation dose rate and surface radioactivity contamination level on the experimental equipments, floors, walls of the facilities, and the surface of the activated materials within the reactor pool structure were measured and evaluated. Radioactivity and radionuclides in the pool and cooling water were also analyzed. In case of the activated reactor pool structures which are very difficult to measure the radiation and radioactivity level, a computer code Fispin was additionally used for estimation of the residual radioactivity and radionuclides. The radiation and radioactivity data obtained in this study were effectively used as basic data for decontamination and dismantling plan for safe decommissioning of TRIGA Mark-II, III facilities.

• Journal of Adhesion and Interface
• /
• v.4 no.1
• /
• pp.1-8
• /
• 2003

In this work, the effect of PMR-15 content on the variation of surface free energy of the DGEBA/PMR-15 blend system was investigated in terms of contact angles and mechanical interfacial tests. Based on FT-IR result of the blend system. C=O (1,772, $1,778cm^{-1}$) and C-N ($1,372cm^{-1}$) peaks appeared with imidization of PMR-15 and -OH ($3,500cm^{-1}$) peak showed broadly at 10 phr of PMR-15 by ring-opening of epoxy. Contact angle measurements were performed by using deionized water and diiodomethane as testing liquids. As a result, the surface free energy of the blends gave a maximum value at 10 phr of PMR-15, due to the significant increasing of specific component. The mechanical interfacial properties measured from the critical stress intensity factor ($K_{IC}$) and the critical strain energy release rate ($G_{IC}$) showed a similar behavior with the results of surface energetics. This behavior was probably attributed to The improving of the interfacial adhesion between intermolecules, resulting from increasing the hydrogen bondings of the blends.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.26 no.4
• /
• pp.743-750
• /
• 1997

Direct measurement of the kinetics of free fatty acid transfer between phospholipid model membrane is technically limited by the rapid nature of the transfer process. Separation of membrane-bound fatty acid by centrifugation has shown that although the equilibrium distribution of free fatty acid is determined by this method, fatty acid transfer occurs too rapidly for accurate kinetic measurements. Recently fluorescence resonance energy transfer(FRET) assay has been developed to examine transfer of fatty acids between membranes. Donor membranes which has fluorescent fatty acid, anthroyloxy fatty acid(AOFA), is mixed with acceptor membranes which has non-interchangeable fluorescent quencher, nitrobenzo-xadiazol(NBD), using stopped flow apparatus. As the fluorescent fatty acids transfer from donor membrane to acceptor membrane, fluorescence intensity would be decreased and the rate and degree of fatty acid transfer can be analyzed. Fatty acid transfer between micelles is more complicated because of bile salt. Therefore in experiments with micelles, fluorescence self quenching assay is used. At high concentrations, a fluorophore tends to quench its own fluorescence causing a reduction in fluorescence intensity. Donor micelles contained self quenching concentrations of fluorophore and acceptor micelles had no fluorophore. Upon mixing of donor and acceptor micelles, the rate of transfer of the fluorophore from the donor to the acceptor was measured by monitoring the release in self quenching when its concentration in donor decreased over time.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.2
• /
• pp.135-146
• /
• 2015

This paper is the fourth on the combustion characteristics of the landfill gas in a constant volume combustion chamber for a large displacement volume commercial engine and the second dealing with torch ignition. It discusses the combustion characteristics of torch ignition on the basis of the heat release and visualization. The results show that the jet and/or spout from the torch promote combustion by accelerating the flame front in the main combustion chamber. In addition, a hot gas jet exists when the orifice diameter is 4 mm, whereas the flame passes directly through the orifice if the diameter is 6 mm or greater. In addition, the effect of torch ignition differs according to the combination of the methane fraction, torch volume, and orifice size because various combustion processes occur as a result of the interaction of these parameters. Finally, it was found that the most suitable torch should have an orifice diameter of not less than 6 mm and an area ratio of not more than 0.15 to secure a consistent combustion process in a real engine.

• Korean Journal of Soil Science and Fertilizer
• /
• v.25 no.4
• /
• pp.342-356
• /
• 1992

Kinetic studies using stirred-flow methods were conducted with the Luisiana soil at three pH levels(pH 5, 6.5, and 8) and three temperature levels(10, 25, and $40^{\circ}C$) to explore effects on the rate of silica retention and release and to find out reaction mechanisms. In this study the maximum silica retention could not be obtained for long enough experimental time. The silica sorption isorption was C type fitted well to Freundlich equation. The pH of the soil suspension increased by the silica release process at low pH treatments(pH 5 and 6.5), while decreased at high pH treatment(pH 8). From the above findings It can be deduced that the mechanism of silica retention is a multilayer forming process to change the ligand form depending on pH condition. In the proposed mechanism the sorbed silica provide new binding sites for additional sorption of silica, while the activation energy for the formation of subsequent layers increases correspondingly. The silica retention and release process were well described by first-order and parabolic diffusion equation. However, clear interpretation for silica sorption mechanism using these equations could not be made. The validity of the fraction term (Fa and Fd) included in first-order and parabolic diffusion equation requires further examinations because the temperature effect on apparent rate constant shows no constant trends among temperature treatments, while there was a good trend in Elovich and modified Freundlich equation where the fraction term was not included.

• Korean Journal of Soil Science and Fertilizer
• /
• v.10 no.3
• /
• pp.135-151
• /
• 1977

The present paper summerizes the studies on clay mineralogical characteristics of Korean soil, relationship between potassium and clay minerals, potassium release pattern of clay minerals and utilization of clay minerals for soil conditioner and fertilizers, which have been carried out in this laboratory. 1. The red yellow podzolic soil is mostly abundant in the upland of Korea and mainly consists of halloysite and weathered intermediates of mica such as illite and vermiculite. 2. With regard to soil parent material, kaolin mineral occurs abundant in soils derived from granite and granite gneiss. Mica is dominant in basaltic soil. The main clay mineral of the soil, originated from the Tertiary, is found montmorillonite and the volcanic soil of Jeju Island has plenty of allophane as its main clay mineral. 3. It is confirmed that the soil fertility depends on the composition of clay minerals. The red yellow podzolic soil, containing lot of kaolin, shows low productivity while the montmorillonite soil has higher productivity. 4. The release rate of solid phase potassium (micas and fixed potassium) follows the 1st order reaction equation in the equilibrium solution of $IN-NH_4OAc$. The potassium release constant is positively correlated with the mica content of the clay but negatively correlated with the content of $14.5{\AA}$ minerals. On the other hand, the potassium release constant has very high correlation with the ratio(Kex/Kt) of exchangeable potassium(Kex) to total potassium(Kt). 5. It is also found that Kex/Kt has rather high correlation with the content of mica and $14.5{\AA}$ minerals existed in the clay as well as the mica content of the soil.

• Advances in concrete construction
• /
• v.2 no.1
• /
• pp.13-27
• /
• 2014

The principal objective of this study is to deepen the characterization studies already led on sand concretes in previous works. Indeed, it consists in studying the effect of the sand type on the main properties of sand concrete: fracture and mechanical properties. We particularly insist on the determination of the fracture characteristics of this material which apparently have not been studied. To carry out this study, four different types of sand have been used: dune sand (DS), river sand (RS), crushed sand (CS) and river-dune sand (RDS). These sands differ in mineralogical nature, grain shape, angularity, particle size, proportion of fine elements, etc. The obtained results show that the particle size distribution of sand has marked its influence in all the studied properties of sand concrete since the sand having the highest diameter and the best particle size distribution has given the best fracture and mechanical properties. The grain shape, the angularity and the nature of sand have also marked their influence: thanks to its angularity and its limestone nature, crushed sand yielded good results compared to river and dune sands which are characterized by rounded shape and siliceous nature. Finally, it should further be noted that the sand concrete presents values of fracture and mechanical properties slightly lower than those of ordinary concrete. Compared to mortar, although the mechanical strength is lower, the fracture parameters are almost comparable. In all cases, the sand grains are debonded from the paste cement during the fracture which means that the crack goes through the paste-aggregate interface.