• Journal of the Korean institute of surface engineering
• /
• v.46 no.4
• /
• pp.145-152
• /
• 2013

The growth behavior of nanocrystalline diamond (NCD) film has been studied for three different substrates, i.e. bare Si wafer, 1 ${\mu}m$ thick W and Ti films deposited on Si wafer by DC sputter. The surface roughness values of the substrates measured by AFM were Si < W < Ti. After ultrasonic seeding treatment using nanometer sized diamond powder, surface roughness remained as Si < W < Ti. The contact angles of the substrates were Si ($56^{\circ}$) > W ($31^{\circ}$) > Ti ($0^{\circ}$). During deposition in the microwave plasma CVD system, NCD particles were formed and evolved to film. For the first 0.5h, the values of NCD particle density were measured as Si < W < Ti. Since the energy barrier for heterogeneous nucleation is proportional to the contact angle of the substrate, the initial nucleus or particle densities are believed to be Si < W < Ti. Meanwhile, the NCD growth rate up to 2 h was W > Si > Ti. In the case of W substrate, NCD particles were coalesced and evolved to the film in the short time of 0.5 h, which could be attributed to the fact that the diffusion of carbon species on W substrate was fast. The slower diffusion of carbon on Si substrate is believed to be the reason for slower film growth than on W substrate. The surface of Ti substrate was observed as a vertically aligned needle shape. The NCD particle formed on the top of a Ti needle should be coalesced with the particle on the nearby needle by carbon diffusion. In this case, the diffusion length is longer than that of Si or W substrate which shows a relatively flat surface. This results in a slow growth rate of NCD on Ti substrate. As deposition time is prolonged, NCD particles grow with carbon species attached from the plasma and coalesce with nearby particles, leaving many voids in NCD/Ti interface. The low adhesion of NCD films on Ti substrate is related to the void structure of NCD/Ti interface.

• Carbon letters
• /
• v.11 no.4
• /
• pp.279-284
• /
• 2010

Graphene is one of the most promising materials for many applications. It can be used in a variety of applications not only as a reinforcement material for polymer to obtain a combination of desirable mechanical, electrical, thermal, and barrier properties in the resulting nanocomposite but also as a component in energy storage, fuel cells, solar cells, sensors, and batteries. Recent research at Michigan State University has shown that it is possible to exfoliate natural graphite into graphite nanoplatelets composed entirely of stacks of graphene. The size of the platelets can be controlled from less than 10 nm in thickness and diameters of any size from sub-micron to 15 microns or greater. In this study we have investigated the influence of melt compounding processing on the physical properties of a polyamide 6 (PA6) nanocomposite reinforced with exfoliated graphite nanoplatelets (xGnP). The morphology, electrical conductivity, and mechanical properties of xGnP-PA6 nanocomposite were characterized with electrical microscopy, X-ray diffraction, AC impedance, and mechanical properties. It was found that counter rotation (CNR) twins crew processed xGnP/PA6 nanocomposite had similar mechanical properties with co-rotation (CoR) twin screw processed or with CoR conducted with a screw design modified for nanoparticles (MCoR). Microscopy showed that the CNR processed nanocomposite had better xGnP dispersion than the (CoR) twin screw processed and modified screw (MCoR) processed ones. It was also found that the CNR processed nanocomposite at a given xGnP content showed the lowest graphite X-ray diffraction peak at $26.5^{\circ}$ indicating better xGnP dispersion in the nanocomposite. In addition, it was also found that the electrical conductivity of the CNR processed 12 wt.% xGnP-PA6 nanocomposite is more than ten times higher than the CoR and MCoR processed ones. These results indicate that better dispersion of an xGnP-PA6 nanocomposite is attainable in CNR twins crew processing than conventional CoR processing.

• Journal of Science and Technology Studies
• /
• v.14 no.2
• /
• pp.85-125
• /
• 2014

This paper explores what we call 'the problem of undone social science' by examining the lack of interests in the social, ethical, and legal issues of synthetic biology among social scientists in Korea. This new field of science, which has emerged in the twenty-first century with the promise of solving future problems of energy, food, and disease in the world, has also created a considerable degree of anxiety over the issues of bioethics, biosafety, and biosecurity. From its beginning, therefore, researchers of synthetic biology in Europe and the U.S. have sought to engage social scientists in their projects. Yet scientists and social scientists in Korea have shown no sign of working together to deal with both potential benefits and risks of synthetic biology. Why this silence? What strategic moves would be needed to overcome the structural barrier for their collaboration? Surveying the diverse methodologies developed during and after ELSI (ethical, legal, social implications) experiments, this paper aims to provide three suggestions that might make possible mutually profitable and continuously stimulating dialogues between the two worlds of science and social science: first, institutionalize the ELSI studies on any newly emerging science and technology of concern; second, explore diverse post-ELSI methodologies experimented elsewhere and develop ones that might be applicable best to the Korean situation; and third and perhaps most important, create an intellectual space and a lawful protection for social scientists to exercise their research freedom at the reasonable level and receive a fair review by their peers, not solely by funding agencies and scientific organizations.

• Journal of Radiation Protection and Research
• /
• v.16 no.2
• /
• pp.27-39
• /
• 1991

The diffusion of Sr-85, Cs-137, Co-60 and Am-241 in compacted domestic bentonite was studied, using a diffusion cell unit in which diffusion took place axially from the center of cylindrical bentonite sample body. The effects of compaction density and heat-treated bentonite on diffusion were analysed. And the diffusion mechanism of radionuclide was also analysed by evaluating the measured diffusivity of anion Cl-36. The apparent diffusivities obtained for Sr-85, Cs-137, Co-60 and Am-241 were $l.07{\times}10^{-11},\;6.705{\times}10^{-13},\;l.226{\times}10^{-13}\;and\; l.310{\times}10^{-14}m^2/sec$, respectively. When the as-pressed density of bentonite increased from $1.8\;to\;2.0g/cm^3$, the apparent diffusivity of Cs-137 decreased by quarter. In the case of bentonite heat-treated to $150^{\circ}C$, no significant change in diffusivity was observed, which showed the possibility that the domestic bentonite could be used as a chemical barrier to retard the radionuclide migration at below $150^{\circ}C$. From the calculated pore and surface diffusivity, the surface diffusion due to the concentration gradient of radionuclide sorbed on the solid phase was found to dominate greatly in total transport process.

• Journal of the Korean Chemical Society
• /
• v.40 no.4
• /
• pp.219-228
• /
• 1996

An ab initio molecular orbital method has been applied to investigation of molecular properties and equilibrium geometries for hexahydroxybenzene triscarbonate (C9O9) and its analogous cyclic compounds (C9S9, C9O6S3, C9O3S6). In these works, the optimized geometry of each compound has been obtained at HF and MP2 levels. These results have shown that the optimized geometries of these compounds prefer D3h planar structure to C3v bowl structure. Calculations of harmonic vibrational frequencies have been also carried out at HF/3-21G* level to analyze normal modes of these compounds. Bonding characters of these compounds are studied by Mulliken and natural populations obtained at HF/6-31G* level. We have also studied the structures and the populations of C6O6 and C6S6 at HF and MP2 levels which are obtained by pyrolyses of C9O9 and analogous compounds. In addition, the single point calculations have been performed to predict the approximate energy barrier for pyrolysis of each compound.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.87-87
• /
• 2000

이온빔 증착에 있어서 전자의 조사가 이온빔 증착기구에 미치는 영향에 대한 연구는 지금까지 보고 되어지지 않았다. 특히 전자의 조사가 증착층의 물성에 영향을 미칠 수 있느지에 대하여 정량적인 결과를 실험을 통하여 제시한 보고는 내가 아는 한 존재하지 않는다. 한편 이와같이 박막 증착에 있어서 전하가 증착되어지는 박막의 물성에 미칠 수 있는 영향에 대해서는 많은 과학자들의 관심사이기도 하다. 본 실험에서는 kaufman ion gun을 이용하여 질소 양이온을, 그리고 Cs+ ion gun을 이용하여 탄소 음이온을 조사하고 이들을 이용하여 CN 박막을 증착하였다. 질소 양이온의 에너지는 100eV, 이온밀도는 70$\mu$A/$\textrm{cm}^2$로 고정하고, 탄소 이온빔(80$\mu$A/$\textrm{cm}^2$)의 에너지를 200cV까지 변화시켜가며 증착하였다. 이때 증착층의 특성에 음 전하의 효과를 유발하기 위하여 350~360$\mu$A/$\textrm{cm}^2$의 전자빔을 이온빔 증착과 동시에 추가로 조사하였고 이의 특성을 전자빔을 조사하지 않고 증착한 CN 박막의 특성과 서로 비교하였다. 또한 증착 표면의 전하 축적에 의한 입사 이온빔의 에너지 감소에 의한 영향을 방지하기 위하여 증착되는 Si 기판에 HF (300kHz, 3.5V) bias를 가하여 주었다. 전자빔의 조사와 동시에 이루어진 CN 박막의 증착은 입사하는 탄소 음 이온빔의 에너지가 80eV에서 180eV 사이일때 원자밀도의 향상과 질소함량의 증가, 그리고 sp2C-N 결합대비 sp3C-N 결합의 향상이 이루어졌음을 확인하였다. 이는 이온빔 충돌에 의하여 피코쵸 정도의 시간대에 이루어지는 박막내의 collision cascade 영역에 이에 의하여 생긴 결함부위에 유입된 음 전하가 위치하면 전하주위의 원자와 polarization을 형성하고 이에 의하여 탄소와 질소의 결합을 형성하는데 필요한 자유에너지의 감소를 수반하는 방향으로 원자의 배열이 이루어지기 때문으로 사료된다. 이와같이 이온빔 에너지가 이온빔 증착 기구의 주요한 인자로 널리 인식되고 있는 kinetic bonding process에 있어서 이온 에너지에 의하여 activation energy barrier를 넘은후, 전자의 조사가 자유에너지를 낮추는 방향으로 최종 결합경로를 조절할 수 있기 때문에 이온빔 증착을 조절할 수 있는 또 하나의 주요한 인자로 받아들여질 수 있으리라 판단된다. 이온빔 프로세스에 의한 DLC 혹은 탄소관련 필름을 형성하는데 있어서 입사 이온빔의 에너지에 의하여 수반되는 thermal spike 혹은 외부 열원에 의한 가열은 박막층의 흑연화를 수반하기 때문에 박막의 sp3 특성을 향상시키기 위하여 회피하여야 할 요소이지만 thermal spike에 의한 국부 영역의 가열과 같은 불가피한 인자가 존재하는 상황에서 전자에 의한 추가 전하의 조사에 의한 최종결합경로의 선택적 조절은 박막의 화학적 결합과 물리적 특성을 향상시킬 수 있는 중요한 방법이 될 수 있다고 판단된다.

• Clean Technology
• /
• v.28 no.4
• /
• pp.301-308
• /
• 2022

Since nanoporous silica aerogel was first synthesized in 1931, its potential as an ultra-lightweight superinsulation material has been steadily attracting attention. Silica aerogel is the best thermal insulation material to date. However, the potential applications of this lightweight material have so far been hindered by its inherent fragibility and brittleness arising from its ultra-porous nature. Although the monolithic form of silica aerogel has the best ultra-lightweight superinsulation properties, it cannot be used in this form. Instead it is used in the form of powders, particles, and blankets. However, these forms still have shortcomings. Silica aerogel is most widely applied in the form of a fiber-reinforced aerogel blanket, but this form is likely to generate dust when handled. Although silica aerogel particles have been proven to be non-toxic to humans, dust formation remains a major barrier to the widespread application of silica aerogel blankets. This paper will investigate the unique properties of silica aerogel and determine what fields it can be used in or potentially be used in due to its unique properties. In addition, we will review the important advances in silica aerogel synthesis technology and its commercialization so far, and then consider the problems that exist for its widespread commercialization in the future and how to overcome them.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.25 no.2
• /
• pp.175-186
• /
• 2023

The buffer materials in disposal hole are exposed to the decay heat from spent nuclear fuels and groundwater inflow through adjacent rockmass. Since understanding of thermal-hydro-mechanical-chemical (T-H-M-C) interaction in buffer material is crucial for predicting their long-term performance and safety of disposal repository, it is necessary to investigate the heating-hydration characteristics and consequent T-H-M-C behavior of the buffer materials under disposal conditions considering geochemical factors. In response, the Korea Atomic Energy Research Institute developed a laboratory-scale 'Lab.THMC' experiment system, which characterizes the T-H-M behavior of buffer materials under different geochemical conditions by analyzing heating-hydration process and stress changes. This technical report introduces the detail design of the Lab.THMC system, summarizes preliminary experimental results, and outlines future research plans.

• Journal of Soil and Groundwater Environment
• /
• v.6 no.4
• /
• pp.61-72
• /
• 2001

A barrier liner system is placed at the bottom and side slope in landfill to protect a leaking of leachate that the hydraulic conductivity of this system should be less than It 107cm/sec. In this study, the soil-bentonite mixture for the bottom liner system was evaluated in two point of views : changing characteristics of the hydraulic conductivity according to the different mixing ratio of soil-bentonite with the effect of bentonite swelling and the difference method (A & D type) of compaction on the hydraulic conductivity. As the results, maximum dry density (${\gamma}$$_{dmax}$) of SC group mixture was higher than of CL group mixture. However, the result of optimum moisture contents(OMC) of both groups were the contrary. In case of ${\gamma}$$_{dmax}$ by different compaction method, D type was higher than A. But the OMC were the contrary. The difference of ${\gamma}$$_{dmax}$ according to the Compaction energy, “SC” group mixture W3S higher than the “CL” group. In case of OMC of “CL” group was higher than “SC” group. The effecting of swelling was a little bit different on the two factors. According to the result of compaction test, the use of site soil only could not meet the criteria on hydraulic conductivity, but could find a solution for the mixing ratio of bentonite mixture were satisfied to the standard of barriation. The increased in bentonite mixing ratio and degree of swelling, the values of hydraulic conductivity were decreased. Especially the “CL” group with “D” type compaction measured the lowest value with the same conditions. Also, the bentonite mixing ratio has more influenced on the hydraulic conductivity compare with swelling effect. The “SC” group mixture with “A” typo compaction got a big difference from others. The evaluation of economic for the construction cost on the two cases, the lower bentonite mixing ratio of soil-bentonite mixed soil is more economically because of bentonite cost.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.12
• /
• pp.803-812
• /
• 2014

This study assesses the strategy and performance of Eco-industrial Park (EIP) initiative implemented by Korea Industrial Complex Corporation (KICOX) with the support of Ministry of Trade, Industry and Energy (MOTIE), Korea since 2005 to 2013 and recommends future directions. After the concept of EIP based on industrial symbiosis (IS) is introduced, the background and implementation procedure of the EIP initiative are described. Then, economic and environmental achievement was assessed. During the project periods (2005-2013), 449 industrial symbiosis project were explored, among which 296 projects have been implemented. Among (Of these 296 projects,) them, 244 projects have been completed in which 118 projects have been commercialized which shows 48% commercialization rate of the completed projects. Through these commercialized projects, around 311.1 billion won/year of economic benefits and reduction of waste by-products of 828,113 tons/year, wastewater of 215,517 tons/year, reduction in energy consumption of 250,475 toe/year and GHG emission reduction of 1,107,189 $tCO_2/year$ were achieved. This results confirmed that EIP initiative based on industrial symbiosis can enhance eco-efficiency of industrial parks and harmonize economy and environment. However, there are obstacles like absence of interagency coordination and cooperation, laws and institutional barriers, increased demand for local governments, funding for project investment. Thus, to utilize EIP initiative as a strategic tool for competiveness and environmental management of industrial parks, it needs intergovernmental collaboration and interdisciplinary approach to lower barrier in implementation.