• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.9
• /
• pp.1051-1056
• /
• 2014

Nitrous oxide ($N_2O$) is naturally generated from biological activity, such as bacteria's material exchange. However, recent $N_2O$ concentration in the atmosphere has being increased by the human activities such as industrial growth. One of factors to increase $N_2O$ concentration in the atmosphere is a $N_2O$ emission caused by the combustion of marine fuel oils. The marine transportation presently handles over 99 percent of the international freight cargoes and the number of ship is continuously increasing with increment of cargoes. In this study, author conducted a series of the experimental investigations on which combustion of fuels containing different element concentrations used in a 4-stroke marine diesel engine affect $N_2O$ emissions in the exhaust gas. Moreover, it is assessed on the extent to which fuel combustion patterns in the combustion chamber affect $N_2O$ emissions.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.2
• /
• pp.573-577
• /
• 2013

Heat pumps come into wide use because high energy efficiency can be obtained and diverse heat sources like geothermal heat, waste heat and air are available. It is necessary for an air source heat pump to defrost in order to remove frost on the surfaces of an outdoor heat exchanger. It is impossible for continuous heating if reverse cycle operation is used as defrosting method, furthermore it causes the degradation of COP. In this study an fin-tube heat exchanger with three rows was used as an outdoor coil. One row among three rows of the heat exchanger was used like a condenser in order to remove frost on it, the others were used as evaporator to accomplish continuous heating. Each row was switched in order from a condenser to an evaporator in specified time interval. Tests were carried out during minimum 180 minutes at the defrost-heating test condition(dry bulb temperature $2^{\circ}C$, wet bulb temperature $1^{\circ}C$) described in KS C 9306. Time-averaged COP was about 20% higher than that of conventional defrosting method.

• Journal of the Korean Institute of Gas
• /
• v.23 no.3
• /
• pp.46-50
• /
• 2019

In this study, the strength stability of an LPG mini tank with a storage capacity of about 250 kg was analyzed by FEM. According to the results of the FEM analysis, it is preferable that the corner radius of the LPG mini tank having a storage capacity of 250 kg is designed to be 175 to 205 mm. Generally, the larger the corner radius of the end plate of the gas storage tank, the higher the safety of the strength, but the volume or capacity of the tank is reduced. Therefore, it is important to derive the optimum design data. Further, in order to securely design the strength of the gas tank, the thickness of the tank is designed to be thick. However, when the thick steel sheet is used, the material and the transportation costs are increased. The result shows that it is preferable to select the optimum thickness of the steel sheet from 4.5 to 5.5 mm. Using the level gauge type of column on the central axis of the gas tank, the safety strength of the LPG tank can be enhanced as much as twice, compared with the tank of the existing level gauge to measure the liquid level by piercing the side wall of the tank.

• Proceedings of the Korean Society of Postharvest Science and Technology of Agricultural Products Conference
• /
• 2002.08a
• /
• pp.54-63
• /
• 2002

Post-harvest technology for rice was focused on in-bin drying system, which consists of about 100, 000 facilities in 1980s. The modernized Rice Processing Complex (RPC) and Drying Storage Center (DSC) became popular for rice dry, storage, process and distribution from 1990s. However, the percentage of artificial drying for rice is 48% (2001) and the ability of bulk storage is about 15%. Therefore it is necessary to build enough drying and bulk storage facilities. The definition of high quality rice is to satisfy both good appearance and good taste. The index for good taste in rice is a below 7% of protein, 17-20% of amylose, 15.5-16.5% of moisture contents and high concentration of Mg and K. To obtain a high quality rice, it is absolutely needed to integrate high technologies including breeding program, cropping methods, harvesting time, drying, storing and processing methodologies. Generally, consumers prefer to rice retaining below b value of 5 in colorimetry, and the whiteness, the hardness and the moisture contents of rice are in order of consumer preference in rice quality. By selection of rice cultivars according to acceptable quality, the periods between harvesting time and drying reduced up to about 20 days. Therefore it is necessary to develop a low temperature grain drying system in order to (1) increase the rate of artificial rice drying up to 85%, (2) keep the drying temperature of below 45C, (3) maintain high quality in rice and (4) save energy consumption. Bulk storage facilities with low temperature storage system (7-15C) for rice using grain cooler should be built to reduce labor for handling and transportation and to keep a quality of rice. In the cooled rice, there is no loss of grain quality due to respiration, insect and microorganism, which results in high quality rice containing 16% of moisture contents all year round. In addition, introducing a low temperature milling system reduced the percentage of broken rice to 2% and increased the percentage of head rice to 3% because of proper hardness of grain. It has been noted that the broken rice and cracking reduced significantly by using low pressure milling and wet milling. Our mission for improving rice market competitiveness goes to (1) produce environment friendly, functional rice cultivars, (2) establish a grade standard of rice quality, (3) breed a new cultivar for consumer oriented and (4) extend the period of storage and shelf life of rice during postharvest.

• Korean Journal of Construction Engineering and Management
• /
• v.23 no.6
• /
• pp.30-42
• /
• 2022

OSC is a type of supply chain and value chain that spans the entire process of construction production (planning, design, construction, maintenance, etc.). It is a method of producing the final object by manufacturing it in a factory, transporting it to the site, installing and construction. This research as is the construction cost was compared for each case A, which applied the PC method, and case B, which applied the RC method. In the case of applying the PC method (excluding the PC design cost), compared to the case where only the RC method was applied, the frame construction cost per unit quantity (m³) increased by about 70% (50% based on the total RC construction type). Of the total frame construction cost of PC method application, PC accounted for 90.2%, 'PC manufacturing cost' 54.8%, 'PC assembly cost' 28.5%, and 'transportation cost' accounted for 6.89%. Also a decision-making framework that can consider both costs and benefits was established. In the case of benefits, the construction period, defect repair, disaster occurrence, energy efficiency, noise/dust/waste, and greenhouse gas emission indicators reflecting OSC technical advantages were presented. It can contribute to providing a basis for helping decision-making on the introduction of PC apartment houses using OSC.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.13 no.4
• /
• pp.243-251
• /
• 2015

Nuclear power is currently the second largest power supply method in Korea and the number of nuclear power plants are planned to be increased as well. However, clear management policy for spent fuels generated from nuclear power plants has not yet been established. The back-end fuel cycle, associated with nuclear material flow after nuclear reactors is a collection of technologies designed for the spent fuel management and the spent fuel management policy is closely related with the selection of a nuclear fuel cycle. Cost is an important consideration in selection of a nuclear fuel cycle and should be determined by adding external cost to private cost. Unlike the private cost, which is a direct cost, studies on the external cost are focused on nuclear reactors and not at the nuclear fuel cycle. In this research, external cost indicators applicable to nuclear fuel cycle were derived and quantified. OT (once through), DUPIC (Direct Use of PWR SF in CANDU), PWR-MOX (PWR PUREX reprocessing), and Pyro-SFR (SFR recycling with pyroprocessing) were selected as nuclear fuel cycles which could be considered for estimating external cost in Korea. Energy supply security cost, accident risk cost, and acceptance cost were defined as external cost according to precedent and estimated after analyzing approaches which have been adopted for estimating external costs on nuclear power generation.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.19 no.1
• /
• pp.1-6
• /
• 2016

Ballast water in ship operation is essential for a safe voyage. However ballast water can contain unwanted organisms that are the cause of disturbing the ecosystem by the transfer of potential invasive species. To prevent the destruction of the environment, the International Convention for the Control and Management of Ship's Ballast Water and Sediments(BWM Convention) was adopted in 2004. BWMS (Ballast Water Management System) has been developed to prevent the transportation of organisms to another region in order to fulfill the requirements IMO (International Maritime Organization) regulations. Nowadays there are about 50 approved Ballast Water Management Systems of various types globally. The most common BWMS types are UV (Ultra Violet), Electrolysis and Ozone. Among these types there are many difficulties in determining the optimum type of BWMS which can be suitable for the user and designer's requirements. The main objective of this research is to select the best BWMS type by using AHP. To apply AHP, the most important criteria for the BWMS development are derived by users and designers. From our results, we can give a guide BWMS type to the developers of BWMS.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.2
• /
• pp.132-138
• /
• 2009

The energy efficiency and environment-friendly aspect of the railway system would be superior to other on-land transportation systems. In a preliminary feasibility study stage and selection of optimal railway corridor, the energy efficiency and problems related to environment are usually not considered. For the selection of optimal railway corridor, geographical features and facility of management are generally considered. Environment effect factors for the selection of environment-friendly railway corridor are focused and studied in this paper. In this study, various analysis of opinion of specialists (railway, environment, transport, urban planning, survey) and the guideline for construction of environment-friendly railway were accomplished. From these results of various analysis, 7 major categories (topography/geology, flora and fauna, Nature Property, air quality, water quality, noise/vibration, visual impact/cultural assets) were extracted. To select environment friendly railway corridors, many alternatives should be compared optimal corridor must be selected by a comprehensive assessment considering these 7 categories. The investment for railway systems can be encouraged by the considering of main environmental effect factor evaluated with the modified environmental weight factors for environment-friendly railway construction.

• Environmental and Resource Economics Review
• /
• v.31 no.3
• /
• pp.419-449
• /
• 2022

This paper aims to quantify the potential economic burdens of EU's carbon border adjustment mechanisms faced by Korean domestic industries. In addition, this study tries to compare and analyzes changes in the burden of each industry resulted from the implementation of the domestic low-carbon policy. Based on the quantitative findings, we intend to suggest policy implications for establishing mid- to long-term strategies in response to climate change risks. Based on the environmentally extended input-output analysis, the total economic burdens of the domestic industries due to the EU's carbon border adjustment mechanisms are estimated to be approximately KRW 8,245.6 billion in 2030. Looking at the impacts by industry, it is found that major industries such as petrochemicals, petroleum refining, transportation equipment, steel, automobiles, and electric/electronic equipment industries are expected to account for 84.3% of the total potential burdens. In addition, in multiple policy scenarios assuming technological developments and energy transition following the implementation of domestic low-carbon policies, the total economic burden of carbon border adjustment is expected to decrease by about 11.7% to 15.0%. The main result of this study suggests that we should not view EU EU's carbon border adjustment mechanism as a trade regulation, but to use it as a momentum for more effective implementation of the low-carbon and energy transition strategies in the global carbon neural era.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.17 no.1
• /
• pp.39-48
• /
• 2009

Biodiesel is estimated to be the best recycling energy source as an alternative fuel for transportation vehicles which represents the biggest share of greenhouse effect gas exhausts. Thus, in order to widely expand use of biodiesel and to enhancement its reliability, studies on quality improvement of biodiesel is needed. In this study, we have produced biodiesel(BD100, BD20) through esterification reaction using raw material of waste frying oil and analyzed compatibility with 24 items of quality criteria. As waste frying oil has high contents of unsaturated fatty acid such as Oleic acid, Linoleic acid and Linolenic acid, it is confirmed that there is no problem in using the same as a raw material of biodiesel. The result of analyzing the quality criteria items of biodiesel showed that it satisfied all the quality criteria except the oxidation stability of BD100, which was 2 hours, fatty acid methyl ester of BD20, which was 18.6w% and the filter plugging point, which was $-5^{\circ}C$. We believe that it will contribute to improved utilization of waste resources as alternative energy if studies on technology to improve quality of some items are provided.