• East Asian mathematical journal
• /
• v.39 no.3
• /
• pp.319-329
• /
• 2023

In this paper, we consider a stochastic higher-order Kirchhoff-type equation with nonlinear damping and source terms. We prove the blow-up of solution for a stochastic higher-order Kirchhoff-type equation with positive probability or explosive in energy sense.

• Proceedings of the KIPE Conference
• /
• 2002.11a
• /
• pp.89-93
• /
• 2002

Hydrogen - Oxygen gas has obtained from water electrolysis reaction. It is mixed gas havingconstant volume ratio 2:1 Hydrogen and Oxygen, and it is used as a source of thermal energy by combustion reaction. This gas has betterristics in the field of economy, efficiency of energy, and environmental intimacy than used both of acetylene gas and LPG for gas welding machin. So nowdays many studies of Water-Electrolyzed gas are progressed, and commercially used as a source of thermal energy for gas welding In the industry. For Water-Electrolyzed Source, it was used diode rectifier or SCR rectifier for get DC source. This method which is not looking to improve a source for impossible current control or voltage and limited control intervals. In this paper, it was relized and designed in source of pulse type for complementing existing-DC source type, also by experiment it was acquired producting characteristics of Hydrogen -Oxygen Gas through feature of source

• Applied Science and Convergence Technology
• /
• v.25 no.6
• /
• pp.116-119
• /
• 2016

In this study, we fabricated the $K^+$ ion source for the various purposes and investigated the emission characteristics. The fabricated $K^+$ ion source was painted in the tungsten filament to make filament type ion source. The RGA spectra show that the filament type $K^+$ ion source has a good out gassing character, so it can be used in the ultra-high vacuum system. The maximum $K^+$ ion current was 20 mA when filament temperature was 1410 K and filament potential was 50 V. When the filament temperature was 1070 K, the initial beam current was 50 mA and decreased only by 2% during 4 hours. The emitting energy was measured to be 2.04 eV. This low value means that the fabricated specimen is a good $K^+$ ion source. We conclude that this filament type ion source can be used in various fields, including the LEIS research.

• Nuclear Engineering and Technology
• /
• v.56 no.1
• /
• pp.70-77
• /
• 2024

A low energy ion irradiation system based on the deuterium arc ion source with a high perveance of 1 µP for a single extraction aperture has been successfully developed for the investigation of ion irradiation on plasma-facing components including the first mirror of plasma optical diagnostics system. Under the optimum operating condition for mirror testing, the ion source has a beam energy of 200 eV and a current density of 3.7 mA/cm². The ion source comprises a magnetic cusp-type plasma source, an extraction system, a target system with a Faraday cup, and a power supply control system to ensure stable long time operation. Operation parameters of plasma source such as pressure, filament current, and arc power with D₂ discharge gas were optimized for beam extraction by measuring plasma parameters with a Langmuir probe. The diode electrode extraction system was designed by IGUN simulation to optimize for 1 µP perveance. It was successfully demonstrated that the ion beam current of ~4 mA can be extracted through the 10 mm aperture from the developed ion source. The target system with the Faraday cup is also developed to measure the beam current. With the assistance of the power control system, ion beams are extracted while maintaining a consistent arc power for more than 10 min of continuous operation.

• Applied Science and Convergence Technology
• /
• v.27 no.4
• /
• pp.65-69
• /
• 2018

We studied the critical pressure characteristics of an anode type ion beam source driven by both charge repulsion and diffusion mechanism. The critical pressure $P_{crit}$ of the diffusion type ion beam source was linearly decreased from 2.5 mTorr to 0.5 mTorr when the gas injection was varied in 3~10 sccm, while the $P_{crit}$ of the charge repulsion ion beam source was remained at 3.5 mTorr. At the gas injection of 10 sccm, the range of having normal beam shape in the charge repulsion ion beam source was about 6.4 times wider than that in the diffusion type ion beam source. An impurity of Fe 2p (KE = 776.68 eV) of 12.88 at. % was observed from the glass surface treated with the abnormal beam of the charge repulsion type ion beam source. The body temperature of the diffusion type ion beam source was observed to increase rapidly at the rate of $1.9^{\circ}C/min$ for 30 minutes and to vary slowly at the rate of $0.1^{\circ}C/min$ for 200 minutes for an abnormal beam and normal beam, respectively.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1997.05b
• /
• pp.159-164
• /
• 1997

Pyrolytic carbon layer was coated on A1203 balls by fluidized bed type chemical vapour deposition unit to develop the coating technology for the preparation of coated nuclear fuel. The deposition was carried out at the temperature ranges between 110$0^{\circ}C$ and 130$0^{\circ}C$ with various gas contents and flow rates. Source and carrier gas were propane and argon, respectively. X-ray analysis shows that the deposition layer was typical carbon spectra. The growth rate of carbon layer depended on the amount of source gas and the deposition temperature. For the alumina balls with 2mm in diameter, the deposition rate was 11${\mu}{\textrm}{m}$/hr in the flow gases containing 30% source gas at 130$0^{\circ}C$ with a total flow rate of 2.0$\ell$/min. Microstructural observation of the deposits with scanning electron microscope revealed that the deposits had relatively dense and isotropic structure. Chemical analysis by energy dispersive spectroscopy showed that the layer was pure carbon.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.14 no.4
• /
• pp.7-12
• /
• 2018

Energy performance of electric heater and geothermal source heat pump type hot air dryers are compared in this study. For set temperatures of $30^{\circ}C$, $35^{\circ}C$ and $40^{\circ}C$, radish is dried from initial mass 60 kg until it gets 5 kg, where the difference equals the amount of water removed. As set temperature is increased, drying time is shortened for both electric heater and heat pump types, however energy efficiency is decreased due to increasing electricity consumption. Moisture extraction rate(MER) of electric heater is 2.58~2.84 kg/h, and for heat pump type 2.56~2.71 kg/h, showing little difference between the two types. Specific moisture extraction rate (SMER) of electric heater is 0.94~0.96 kg/kWh, and for heat pump type 1.72~2.21 kg/kWh. SMER of heat pump type is greater by 0.78~1.25 kg/kWh than the electric heater hot air dryer, which is 1.8~2.3 times better in terms of energy efficiency.

• Journal of the Korean Solar Energy Society
• /
• v.39 no.1
• /
• pp.67-76
• /
• 2019

A ground source heat pump (GSHP) system can stable system operation by using underground heat source and has high reliability for energy production. However, wide-spread of the GSHP system is delayed to high initial investment costs. In previous studies, horizontal and unit-type ground heat exchanger (GHX) have developed to overcome disadvantages such as high initial cost. However, these performances of GHXs are greatly influenced by climate and weather conditions. It is necessary to analyze the performance of GHX according to the ground temperature change in the installation site. In this study, the ground temperature of each installation site confirmed and performance of unit-type GHX quantitatively analyzed by numerical analysis. As the result, the performance of the unit type GHX was 33.9 W/m in Seoul, 34.2 W/m in Daejeon, and 37.2 W/m in Busan.The result showed the difference performance of GHX according to local climate was maximum of 9.7%.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.8
• /
• pp.37-51
• /
• 2013

An energy pile encases heat exchange pipes to exchange thermal energy with the surrounding ground formation by circulating working fluid through the pipes. An energy pile has many advantages in terms of economic feasibility and constructability over conventional Ground Heat Exchangers (GHEXs). In this paper, a coil-type PHC energy pile was constructed in a test bed and its thermal performance was experimentally and numerically evaluated to make a preliminary design. An in-situ thermal response test (TRT) was performed on the coil-type PHC energy pile and its results were compared with the solid cylinder source model presented by Man et al. (2010). In addition, a CFD numerical analysis using FLUNET was carried out to back-analyze the thermal conductivity of the ground formation from the Ttype PHC energy RT result. To study effects of a coil pitch of the coil-type heat exchange pipe, a thermal interference between the heat exchange pipes in PHC energy piles was parametrically studied by performing the CFD numerical analysis, then the effect of the coil pitch on thermal performance and efficiency of heat exchange were evaluated. Finally, an equivalent heat exchange efficiency factor for the coil-type PHC energy pile in comparison with a common multiple U-type PHC energy pile was obtained to facilitate a preliminary design method for the coil-type PHC energy pile by adopting the PILESIM2 program.

• Proceedings of the KIEE Conference
• /
• 2004.04a
• /
• pp.247-249
• /
• 2004

Electric systems can be classified into two classes on the basis of the location of its energy source. One system is to be connected with its outside energy source. Obviously, these electric system is limited of its motion range and impossible to operate in the situation without a way to find an energy source nearby. another is to posses the energy source within it. These electric systems are free of motion range limit while their using is limited by the life of source. These limits can be tided over by using passive-type RF communication. RF-ID is a system that Is possible to interchange electricity and data by Radio Frequency to locate and identify various objects including a man.