• Journal of Animal Science and Technology
• /
• v.48 no.5
• /
• pp.699-708
• /
• 2006

Ground rice, barley and corn were fed separately to the ruminally cannulated Hanwoo (Korean native cattle) for comparing their in situ and in vitro degradabilities, microbial growth, pH and gas production. It has been found that nearly all the dry matter (DM) and organic matter (OM) in barley and rice disappeared during 24 hr suspension in the rumen, but those in corn were only reduced by around 67%. Water soluble DM and OM fractions(‘a’), ranked from highest to lowest was corn, then rice and finally barley, but the order was reversed for content ‘b’, degradable fraction during time ‘t’. Judging by the degradation parameter of ‘b’ fraction, degradation rates per hour of DM and OM for barley were 38.3% and 37.2% respectively, significantly higher than those for rice (7.7% and 5.6%) and corn (4.1% and 1.3%). In general, results obtained from in vitro degradability of DM and OM were lower than those from in situ trials, but the ranking order of degradability was in agreement between both trials. In particular, ground rice has relatively lower in vitro microbial growth than corn or barley, but exhibited higher gas production. In addition, in vitro microbial growth of ground rice increased with up to 12 hr of incubation period, thereafter experienced a decrease with extended incubation time. pH of in vitro solution of rice decreased following 9 hr of incubation but gas production increased rapidly during the same period. From the results of DM and OM degradabilities and pH changes of in vitro solution with incubation time, it is concluded that rice represents a good source of energy for stability of rumen fermentation.

• The Korean Journal of Food And Nutrition
• /
• v.11 no.2
• /
• pp.179-184
• /
• 1998

As a way of mass process of onion, Allium cepa L., the oleoresin decompressed and concentrated is an alternative process to minimize lowering in the quality of onion during storage, to improve the original flavor and taste, and to increase variety as processing aids. This study was performed to investigate on the quality stability during storage of oleoresin. Oleoresin product was manufactured by mixing a concentration of onion juice and ethanol extract homogenously, emulsified by an additional 2% PGDR(polyglycerol condensed ricinoleate) and 1% cysteine. During 60 days storage at 5$^{\circ}C$, $25^{\circ}C$ and 4$0^{\circ}C$ the total sugar content in oleoresin product was very stable, and absorbances at 420nm as browning reaction index were 0.38, 1.53 and 3.32, respectively, addition of 1% cysteine retarded the browning reaction effectively. When oleoresin product was centrifuged(2000$\times$G, 60 minutes), the volumes of emulsion level without separation were 96.8%, 94.1% and 9.06%, respectively during 20 days, 40 days and 60 days storage at 5$^{\circ}C$, and those during 60 days storage at $25^{\circ}C$ and 4$0^{\circ}C$ were appeared to be 83.2% and 75.4%. Showing lower level as increasing storage temperature. Antioxidant indexes(AI) of soybean oil added 1% oleoresin without storage and 0.02% BHA were 1.39 and 1.72. The former showed 80.8% antioxidant activity on induction time extension effect of the latter. Antioxidant indexes of oleoresin decreased slightly as increasing storage temperature and were 1.37, 1.30 and 1.08. Total pyruvate contents were 89.9%, 79.7% and 65.2%, respectively during 60 days storage at 5$^{\circ}C$, $25^{\circ}C$ and 4$0^{\circ}C$. Rate constant, Q10 value and activation energy were 1.381~4.735 mmol/$\ell$.hr, 1.537~1.694 and 11.649 ㎉/g mole for the reduction of pyruvates in the range of storage temperatures during oleoresin storage.

• Journal of Life Science
• /
• v.21 no.3
• /
• pp.412-416
• /
• 2011

Taste sensation plays a crucial role in selecting and ingesting foods with different qualities which convey information about their nutrient content and/or safety. Sweetness is one of the five modalities in humans and serves as an energy resource for metabolism. There are reports on allelic polymorphisms which influence perception of sweetness in mice and humans. Since the influence of genetic factors on taste disorder has not been studied, we investigated the association of genetic polymorphisms in TAS1R3 and guanine nucleotide binding protein, alpha transducing 3 (GNAT3) genes and taste disorder. A total of 150 individuals composed of 50 patients with taste disorder and 100 healthy controls were recruited for the study and PCR-mediated directing sequencing method was used to genotype for two different single nucleotide polymorphisms (SNPs) - rs307355 (T>C) and rs35744813 (T>C) in the TAS1R3 gene, and rs7792845 (T>C) and rs1524600 (C>T) in the the GNAT3 gene. The allele and genotype frequencies of rs307355 and rs35744813 in the TAS1R3 gene showed a significant association between patients with taste disorder (p=0.022 and p=0.013 in both of SNPs, respectively). In addition, the frequency of T-T haplotype in the TAS1R3 gene was higher in taste disorder cases than in the controls (OR, 1.93: 95%. CI, 1.09-3.39, p=0.022). In the GNAT3, the genotype frequency of rs7792845 in the patients was also different from the controls (p=0.048), but allele frequency was not significantly associated in either group. Our result provides the frequencies of SNPs and haplotypes of the TAS1R3 and GNAT3 genes for the fundamental information of nutrigenetics in perception of the taste of sweetness in the Korean population. Also, the study suggests that the allelic polymorphisms of TAS1R3 and GNAT3 genes may be useful as a molecular marker for evaluating patients with taste disorder. Further studies with large samples are required to clarify our observation.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.9 no.3
• /
• pp.203-212
• /
• 2005

Cellulose insulation is primarily manufactured from recycled newsprint and treated with fire retardants for the fire resistance. Thanks to the fire retardants, it is not combustible and flammable. In addition to that, Its thermal resistance is much better than that of fiberglass or rock wool. It is made from waste paper and easily decayed when it is demolished, and it has small embodied energy. So it is very environment-friendly building material. For broader use of cellulose insulation in buildings in Korea, it is necessary to test its physical performance to compare the results with the requirements on the Korean Building Code. To this end, apparent thermal conductivity (ka) measurements of Korean-made loose-fill cellulose insulations were recently completed using equipment that was built and operated in accordance with ASTM C 518 and the fire resistance was tested in accordance with ASTM C 1485. Korean loose-fill cellulose has thermal conductivity about 5% greater than the corresponding U.S. product at the same density. This is likely due to differences in the recycled material being used. Both spray-applied and loose-fill cellulose insulation lose about 1.5% of their thermal resistivity for $5.5^{\circ}C$ increase in temperature. The fire resistance of cellulose insulation is increased in linear proportion to the increase of the rate of fire retardant. Thanks to the high fire resistance, cellulose insulation can be used as a substitution of Styrofoam or Urethane foam which is combustible. The thermal conductivity of cellulose insulation was $0.037-0.043W/m{\cdot}K$ at the mean specimen temperature from $4-43^{\circ}C$. It corresponds to the thermal resistance of "Na Grade" according to the Korean Building Code. The effect of chemical content on thermal conductivity was negligible for all but the chemical-free specimen which had the highest value for the thermal conductivity over the temperature range tested. The thermal resistance of cellulose insulation is better than that of fiberglass or rock wool, and its fire resistance is higher than that of Styrofoam or Urethane foam. Therefore it can be substituted for those above considering its physical performance. Cellulose insulation is no more expensive than Styrofoam or rock wool, so it is recommended to use it more widely in Korea.

• Korean Journal of Materials Research
• /
• v.8 no.12
• /
• pp.1158-1164
• /
• 1998

Aluminium sulfate solution was prepared by sulfuric acid treatment from gibbsite. Aluminium sulfate hydrate [$Al_2(SO_4)_3$ · $nH_2O$] was precipitated from aluminium sulfate solution by adding it into ethylalcohol. From XRD analysis as-prepared $Al_2(SO_4)_3$ · $nH_2O$ was confirmed to have mixed-crystalization water(n=18, 16, 12, 6). The average water of crystalization calculated from thermogravimetry(TG) was 14.7. Aluminium sulfate hydrate [$Al_2(SO_4)_3$ · $nH_2O$] was thermally decomposed and converted to $Al_2(SO_4)_3$ at $800^{\circ}C$, $\gamma-Al_2O_3$ at $900-1000^{\circ}C$, and $\alpha-Al_2O_3$ at $1200^{\circ}C$. Ni-doped $\gamma-Al_2O_3$, was synthesized from the slurry of as-prepared $\gamma-Al_2O_3$, with the ratio of [Ni]/[Al]=0.5. The reaction conditions of synthesis were determined as initial pH 9.0 and temperature $80^{\circ}C$ The basicity(pH) of slurry was controlled by using urea and $NH_4OH$ solution. Urea was also used for deposition-precipitation. For determining termination of reaction, the data acquisition was performed by oxidation reduction potential(ORP), conductivity and pH value in the process of reaction. Termination of the reaction was decided by observing the reaction steps and rapid decrease in conductivity. On the other hand, BET(Brunauer, Emmett and Teller) and thermal diffusity of Ni- doped $\gamma-Al_2O_3$, with various content of Ni were measured and compared. Thermal stability of Ni- doped $\gamma-Al_2O_3$ at $1250^{\circ}C$ was confirmed from BET and XRD analysis. The surface state of Ni-doped $\gamma-Al_2O_3$ was investigated by X-ray photoelectron spectroscopy(XPS). The binding energy at $Ni2P_{3/2}$ increased with increasing the formation of $NiAl_2O_4$ phase.

• Journal of Conservation Science
• /
• v.32 no.4
• /
• pp.579-588
• /
• 2016

This study analyzed nonmetallic inclusions in iron swords with a ring pommel excavated in the Ipbuk-dong, Suwon. Scanning electron microscopy with energy dispersive spectroscopy(SEM-EDS) was used to estimate the iron-making temperature, and we compared the oxide with $SiO_2$ to investigate the heat-treatment technology in the production of iron swords with a ring pommel by investigating the artificial insertion of a slag former and the metallurgical structure. From the wustite observed in most of the specimens, it is judged that these swords were produced by heating and forging iron smelted at a low temperature using the solid reduction method. In addition, judging from the partial presence of $P_2O_5$, it is assumed that they were smelted directly with natural ore, not calcined. From the ratios of $CaO/SiO_2$ and $TiO_2/SiO_2$, it is judged that the raw material for iron-making was iron ore and that a calcareous slag former was not artificially inserted. The structure of the blade part on the front end was pure iron. From the high carbon content of the blade part on the ring pommel and the formation of a martensitic structure and pearlite colony, it is judged that they were tempered after carburizing and that the back, handle part, and ring pommel were unintentionally carburized. Judging from the structure of these specimens, it was noted that they were produced by applying artificial partial heat-treatment technology. This study attempted to present a more scientific analysis by using the method of interpretation through component analysis of nonmetallic inclusions appearing in one relic by the ratio of the oxide divided by $SiO_2$. It is judged that reinterpreting the arguments by the results of the existing analysis and research in this way can obtain different interpretations.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.15 no.2
• /
• pp.181-189
• /
• 1986

This nutrition survey was carried out twice(Spring and autumn) in Sam Chung-Ri, Song Kwang Myun, Soong Ju-Gun. The food intakes of 92 family members were measured by weighing method. Also 45 adults were examined for anthropometric, blood content and blood pressure. The results abtained were summarized as follows; In vegetable foods, the intake of rice was high, but that of legumina and other cereals was low. In animal foods, the intake of milk and eggs was low, and that of oils and fats was very low. However, the food intake between spring and autumn showed remarkable difference. The average intake of calorie, protein, Ca, Fe and vitamin $B_2$ except vitamin $B_1$ and niacin was below the RDAs. The percentage of carbohydrate, protein and fat for energy was 82.2, 11.6 and 6.2%, respectively. The results of anthropometry of height, weight and chestcircumference showed that both sexes Were below Korean Standards. The concentration of Hb & Hct was normal in both sexes, and the rate of anemia was low. The concentrations of plasma glucose, protein, lipids, and blood pressure were normal in both sexes. In case of male, the correlation between plasma albumin and nutrients intake was significant, but the case of female showed different tendency. In case of male, the correlation between weight, height and plasma protein was also significant but the case of female showed different tendency. The rate of parasite infection was very low $(2.17%{\ldots}3.26%)$

• Korean Chemical Engineering Research
• /
• v.46 no.5
• /
• pp.1008-1012
• /
• 2008

Nanoscale zero-valent iron(nZVI) is famous for its high reactivity originated from its high surface area and it has received considerable attentions as one of the latest innovative technologies for treating contaminated groundwater. Due to its fine powdery form, nZVI has limited filed applications. The efforts to overcome this shortcoming by immobilizing nZVI on a supporting material have been made. This study investigated the differences of resin-supported nZVI's characteristics by changing the preparation methods and evaluated its reactivity. The borohydride reduction of an iron salt was proceeded in ethanol/water solvent containing a dispersant and the synthesis was conducted in the presence of ion-exchange resin. The resulting material was compared to that prepared in a conventional way of using de-ionized water by measuring the phyrical and chemical characteristics. BET surface area and Fe content of nZVI-attached resin was increased from $31.63m^2/g$ and 18.19 mg Fe/g to $38.10m^2/g$ and 22.44 mg Fe/g, respectively, by switching the solution medium from water to ethanol/water with a dispersant. The reactivity of each material was tested using nitrate solution without pH control. The pseudo first-order constant of $0.462h^{-1}$ suggested the reactivity of resin-supported nZVI prepared in ethanol/water was increased 61 % compared to that of the conventional type of supported nZVI. The specific reaction rate constant based on surface area was also increased. The results suggest that this new supported nZVI can be used successfully in on-site remediation for contaminated groundwater.

• Clean Technology
• /
• v.20 no.4
• /
• pp.375-382
• /
• 2014

This work investigated the plasma-catalytic decomposition of isopropyl alcohol (IPA) and the behavior of the byproduct compounds over monolith-supported metal oxide catalysts. Iron oxide ($Fe_2O_3$) or copper oxide (CuO) was loaded on a monolithic porous ${\alpha}-Al_2O_3$ support, which was placed inside the coaxial electrodes of plasma reactor. The IPA decomposition efficiency itself hardly depended on the presence and type of metal oxides because the rate of plasma-induced decomposition was so fast, but the behavior of byproduct formation was largely affected by them. The concentrations of the unwanted byproducts, including acetone, formaldehyde, acetaldehyde, methane, carbon monoxide, etc., were in order of $Fe_2O_3/{\alpha}-Al_2O_3$ < $CuO/{\alpha}-Al_2O_3$ < ${\alpha}-Al_2O_3$ from low to high. Under the condition (flow rate: $1L\;min^{-1}$; IPA concentration: 5,000 ppm; $O_2$ content: 10%; discharge power: 47 W), the selectivity towards $CO_2$ was about 40, 80 and 95% for ${\alpha}-Al_2O_3$, $CuO/{\alpha}-Al_2O_3$ and $Fe_2O_3/{\alpha}-Al_2O_3$, respectively, indicating that $Fe_2O_3/{\alpha}-Al_2O_3$ is the most effective for plasma-catalytic oxidation of IPA. Unlike plasma-alone processes in which tar-like products formed from volatile organic compounds are deposited, the present plasma-catalyst hybrid system did not exhibit such a phenomenon, thus retaining the original catalytic activity.

• Korean Journal of Agricultural Science
• /
• v.6 no.1
• /
• pp.56-64
• /
• 1979

Two types of fiat-plate collector were designed and constructed for utilizing the solar energy as heating source of red pepper drying. It was performed to investigate the basic factors on using the collectors and the drying effect on various types of red pepper, and the results obtained are summarized as follows. 1. The optimum tilted angles of the collector in Daejeon area were ${\phi}-15^{\circ}$ in summer season and ${\phi}+15^{\circ}$ in winter season when it was adjusted two times per a year: 2. In the conditions during experiment period, average atmospheric temperature and relative humidity were $25.6^{\circ}C$ and 52.6%, respectively, and $42.0^{\circ}C$, 74.2% in the control chamber. The temperature in the drying chamber connected to the water heater was the highest but relative humidity in the chamber connected to the air heater was the lowest among the chambers. 3. The drying velocity of whole red pepper in the chamber connected to the water heater was the fastest as 2.3 times as compared to the whole type on the mat drying followed by air heater and control in decreasing order. The horizontally cut red pepper in the chamber connected to the water heater was dried exceedingly fast among twelve plots. 4. The content of capsaicine as pungent principle and of capsanthine as red pigment in the red pepper were reduced during drying but there were no differences significantly on the drying method, and it could not affect much on the quality of dried product.