• Restorative Dentistry and Endodontics
• /
• 제20권1호
• /
• pp.152-163
• /
• 1995

This experiment was performed to observe the adhesion pattern and microleakage in the gingival margin according to variation in the resin cement thickness which results from thickness of Die spacer. which is considered to effect the adaptability of the composite resin inlays. Clearfil CR inlays were fabricated on stone models with CR Sep applicated once and Nice fit twice, 4 times, and 6 times each. After 2nd curing within the CRC-100 oven, CR inlays were cemented with CR inlay cement. Dye(2% methylene blue) penetration and adhesion pattern were evaluated after sectioning of gingival margin into :3 pieces. The results were as follows ; 1. The thickness of resin cement showed unevenchanging pattern with that of die spacer, namely, it was increased until 4 times' application of Nice-Fit but was decreased with 6 times' application of that. 2. The degree of dye penetration wasn't affected by cement thickness within a limited value. 3. Most of dye penetration was shown through the interface between cement and enamel rather than the interface between cement and CR inlay. This shows that the affinity of resin cement for CR inlay was superior to the adhesive strength with tooth structure. 4. No gap was found at the interface between enamel and cement but some showed separation between dentin and cement. It is concidered that the contraction force of cement was less than the bond strength with the enamel. 5. Lots of voids were found in the CR inlay and resin cement. There was a pooling tendency of bonding agent and cement in the axiogingival line angle portion. 6. In some specimens, cracks were shown in enamel margin. From this it could be considered that cavity preparation and surface treatment weakened the tooth structure.

• Restorative Dentistry and Endodontics
• /
• 제24권4호
• /
• pp.647-656
• /
• 1999

The purpose of this study was to investigate the shear bond strength and marginal microleakage of composite to enamel and dentin according to different treatment methods when the applied bonding agent was contaminated by artificial saliva. For the shear bond strength test, the buccal and occlusal surfaces of one hundred twenty molar teeth were ground to expose enamel(n=60) and dentin surfaces(n=60). The specimens were randomly assigned into control and 5 experimental groups with 10 samples in each group. In control group, a bonding system(Scotchbond$^{TM}$ Multi-Purpose plus) and a composite resin(Z-100$^{TM}$) was bonded on the specimens according to manufacture's directions. Experimental groups were subdivided into 5 groups. After polymerization of an adhesive, they were contaminated with at artificial saliva on enamel and dentin surfaces: Experimental group 1 ; artificial saliva was dried with compressed air. Experimental group 2 ; artificial saliva was rinsed with air-water spray and dried. Experimental group 3 ; artificial saliva was rinsed, dried and applied an adhesive. Experimental group 4 ; artificial saliva was rinsed, dried, and then etched using phosphoric acid followed by an adhesive. Experimental group 5, artificial saliva was rinsed, dried, and then etched with phosphoric acid followed by consecutive application of both a primer and an adhesive. Composite resin(Z-100$^{TM}$) was bonded on saliva-treated enamel and dentin surfaces. The shear bond strengths were measured by universal testing machine(AGS-1000 4D, Shimaduzu Co. Japan) with a crosshead speed of 5mm/minute under 50kg load cell. Failure modes of fracture sites were examined under stereomicroscope. The data were analyzed by one-way ANOVA and Tukey's test. For the marginal microleakage test, Class V cavities were prepared on the buccal surfaces of sixty molars. The specimens were divided into control and experimental groups. Cavities in experimental group were contaminated with artificial saliva and those surfaces in each experimental groups received the same treatments as for the shear test. Cavities were filled with Z-100. Specimens were immersed in 0.5% basic fuchsin dye for 24 hours and embedded in transparent acrylic resin and sectioned buccolingually with diamond wheel saw. Four sections were obtained from the one specimen. Marginal microleakages of enamel and dentin were scored under streomicroscope and averaged from four sections. The data were analyzed by Kruskal-Wallis test and Fisher's LSD. The results of this study were as follows. 1. The shear bond strength to enamel showed lower value in experimental group 1(13.20${\pm}$2.94MPa) and experimental group 2(13.20${\pm}$2.94MPa) than in control(20.03${\pm}$4.47MPa), experimental group 4(20.96${\pm}$4.25MPa) and experimental group 5(21.25${\pm}$4.48MPa) (p<0.05). 2. The shear bond strength to dentin showed lower value in experimental group 1(9.35${\pm}$4.11MPa) and experimental group 2(9.83${\pm}$4.11MPa) than in control group(17.86${\pm}$4.03MPa), experimental group 4(15.04${\pm}$3.22MPa) and experimental group 5(14.33${\pm}$3.00MPa) (p<0.05). 3. Both on enamel and dentin surfaces, experimental group 1 and 2 showed many adhesive failures, but control and experimental group 3, 4 and 5 showed mixed and cohesive failures. 4. Enamel marginal microleakage was the highest in experimental group 1 and there was a significant difference in comparison with other groups (p<0.05). 5. Dentin marginal microleakages of experimental group 1 and 2 were higher than those of other groups (p<0.05). This result suggests that treatment methods, re-etching with 35% phosphoric acid followed by re-application of adhesive or repeating all adhesive procedures, will produce good effect on both shear bond strength and microleakage of composite to enamel and dentin if the polymerized bonding agent was contaminated by saliva.

• 치위생과학회지
• /
• 제9권5호
• /
• pp.557-561
• /
• 2009

본 연구에서는 코카콜라, 게토레이, 하이트맥주, 그리고 제주삼다수로 법랑질 표면을 처리한 후 다음과 같은 결론을 얻었다. 1. 음료 처리 전후 표면미세경도차는 코카콜라에서 $166.97{\pm}51.69\;{\Delta}VHN$로 가장 큰 경도차를 보였으며, 그 다음으로 게토레이($116.26{\pm}20.81\;{\Delta}VHN$), 하이트맥주($77.89{\pm}55.88\;{\Delta}VHN$), 제주삼다수($23.44{\pm}29.97\;{\Delta}VHN$)의 순으로 나타났다. 2. 음료 처리 전후 표면거칠기 차이는 게토레이에서 $0.26{\pm}0.67\;{\Delta}Ra$로 가장 큰 거칠기 차이를 보였으며, 그 다음으로 코가콜라($0.05{\pm}0.06\;{\Delta}Ra$), 하이트맥주($0.01{\pm}0.01\;{\Delta}Ra$), 제주삼다수($0.01{\pm}0.00\;{\Delta}Ra$)의 순으로 나타났다. 3. 음료처리 전후 DIAGNOdent 수치 차이는 코카콜라에서 $23.27{\pm}5.91$로 가장 큰 수치 차이를 보였으며, 그 다음으로 게토레이($2.07{\pm}0.99$), 제주삼다수($1.73{\pm}1.22$), 하이트맥주($1.20{\pm}0.92$)의 순으로 나타났다. 4. 음료 처리 후 주사전자현미경 상의 법랑질 표면은 게토레이에서 가장 많은 탈회 현상이 관찰되었다. 이상의 결과를 종합해볼 때 시판 음료가 법랑질 표면을 탈회시키기는 하지만 그 정도가 통계적으로 유의한 수준은 아니었으므로 향후 시판 음료에 Mutans Streptococci(MS)를 추가한 연구가 뒤따라야 할 것으로 사료된다.

• 대한치과교정학회지
• /
• 제26권4호
• /
• pp.389-399
• /
• 1996

치과교정장치의 장착을 위하여 치아법랑질표면을 산부식하는 것은 일반화된 술식이며, 산부식된 법랑질표면은 재석회화되어 자연적으로 정상상태를 회복하는 연구보고되어 왔다. 이 연구의 목적은 산부식된 법랑질표면의 재석회화에 불소가 미치는 영향을 실험적으로 관찰하여 재석희화의 일면을 구명하는데 있다. 교정치료목적으로 발거한 사람 제1소구치 치관을, 불소함유 석회화용액과 불소무함유 석회화용액에 12시간, 1일, 3일, 7일, 14일, 28일, 42일간 담구어 보관한후, 법랑질표면의 미세경도측정과 주사전자현미경관찰을 통하여 법랑질 표면의 변화들을 경시적으로 관찰하여 다음의 결과를 얻었다. 1) 표면미세경도는 불소함유 여부에 관계없이 시간경과에 따라 증가하였으며, 불소함유군 은 12시간부터, 불소무 함유군은 3일경과후부터 현저히 증가하였으나, 시간경과에 따라 그 차이는 감소하였다. 2) 주사전자현미경 관찰에서 불소함유용군은 12시간후부터 법랑질표면에 침상물질이 침착되기 시작하여 42일 후에는 편평한 표면으로 되었으나, 불소무함유용군은 전실험기간동안 산부식직후보다 약간 더 거칠어졌으나, 산부식 된 법랑질표면이 그대로 관찰되었다. 이상의 결과로부처 불소는 산부식된 법랑질표면의 재석회화 시기를 앞당기는 효과가 있으며, 재석회화의 소요시간도 단축하는 효과가 있음이 확인하였다.

• 대한치과보철학회지
• /
• 제17권1호
• /
• pp.23-34
• /
• 1979

In this study, the adhesive strength of three commercial polycarboxylate cements to ten types of dental casting alloys, such as gold, palladium, silver, indium, copper, nickel, chromium, and human enamel and dentine were measured and compared with that of a conventional zinc phosphate cement. The $8.0mm{\times}3.0mm$ cylindrical alloy specimens were made by casting. The enamel specimens were prepared from the labial surface of human upper incisor, and the dentine specimens were prepared from the occulusal surface of the human molar respectively. Sound extracted human teeth, which had been kept in a fresh condition since, extraction, were mounted in a wax box with a cold-curing acrylic resin to expose the flattened area. The mounted teeth were then placed in a Specimen Cutter (Technicut) and were cut down under a water spray, and then the flat area on the all specimens were ground by hand with 400 and 600 grit wet silicone carbide paper. Two such specimens were then cemented together face-to-face with freshly mixed cement, and moderate finger pressure was applied to squeeze the cement to a thin and uniform film. All cemented specimens were then kept in a thermostatic humidor cabinet regulated at $23{\pm}2^{\circ}C.$ and more than 95 per cent relative humidity and tested after 24 hours and 1 week. Link chain was attached to each alloy specimen to reduce the rigidity of the jig assembly, and then all the specimens were mounted in the grips of the Instron Universal Testing Machine, and a tensile load was delivered to the adhering surface at a cross head speed of 0.20 mm/min. The loads to which the specimens were subjected were recorded on a chart moving at 0.50 mm/min. The adhesive strength was determined by measuring the load when the specimen separated from the cement block and by dividing the load by the area. The test was performed in a room at $23{\pm}2^{\circ}C.$ and $50{\pm}10$ per cent relative humidity. A minimum of five specimens were tested each material and those which deviated more than 15 per cent from the mean were discarded and new specimens prepared. From the experiments, the following results were obtained. 1) It was found that the adhesive strength of the polycarboxylate cement to all alloys tested was considerably greater than that of the zinc phosphate cement. 2) The adhesive strength of the polycarboxylate cements was superior to the non precious alloys, such as the copper, indium, nickel and chromium alloys, but it was inferior to the precious gold, silver and palladium alloys. 3) Surface treatment of the alloy was found to be an important factor in achieving adhesion. It appears that a polycarboxylate cement will adhere better to a smooth surface than to a rough one. This contrasts with zinc phosphate cements, where a rough helps mechanical interlocking. 4) The adhesion of the polycarboxylate cement with enamel was found superior to its adhesion with dentine.

• 치위생과학회지
• /
• 제16권3호
• /
• pp.235-241
• /
• 2016

어린이 해열 진통제 중 안전상비의약품 3종을 유치에 적용하여 시간 경과에 따른 유치의 표면과 경도변화를 SEM과 EDX로 비교 분석하여 부식 가능성을 알아보고자 본 연구를 시행하여 다음과 같은 결과를 얻었다. 유치 법랑질 표면미세경도 측정 결과, 처리 전은 모든 군에서 유의한 차이가 나타나지 않았으나(p>0.01), 3일, 5일, 8일 경과 후 각군 간에서는 유의한 차이를 나타냈다(p<0.01). EDX를 이용하여 Ca과 P의 정량분석 결과, 유치 법랑질 기질 내 Ca은 8일 경과 후 각 군 간에서는 유의한 차이가 나타났고(p<0.05), P은 모든 군에서 유의한 차이가 나타나지 않았다(p>0.05). SEM을 이용하여 유치 표면을 관찰한 결과, pH가 가장 낮은 어린이용 타이레놀 정이 표면 거칠기가 가장 심한 것으로 관찰되었고, 다음으로 어린이 부루펜 시럽, 어린이 타이레놀 현탁액, 증류수 순이었다. 이상의 연구 결과를 통해 pH가 낮은 어린이 해열 진통제는 법랑질 표면에 치아 부식을 일으킬 수 있는 가능성이 있고, Ca과 P의 소실은 치아우식증에 이환될 수도 있다. 따라서 어린이 해열 진통제 투약 시 유 아동은 칫솔질과 같은 구강위생관리가 필요하다고 생각된다. 또한 제약회사에서는 이러한 약품들을 복용한 유 아동들이 구강위생조치를 할 수 있도록 약품 내 주의사항 안내서에 치아부식 가능성을 고지해야할 것으로 생각된다.

• Restorative Dentistry and Endodontics
• /
• 제23권1호
• /
• pp.247-256
• /
• 1998

To evalutate the change in shear bond strength according to dentin surface treatment, 4 materials were divided into control group(A) and experimental group(B). Group A was treated according to the instruction of manufacture. Group B was treated with 32% phosphoric acid. After dentin surface treatment, each material was bonded and stored in 100% humidity during 7 days, and then, the shear bond strength was evaluated. The results were as follows: 1. In the case of treatment according to the instruction of manufacture, the shear bond strength according to material showed Z-100 to be highest with 12.42 MPa, Compoglass had the lowest shear bond strength with 4.23 MPa and there was significant difference between Compoglass and Z-100, Dyract (p<0.01). 2. The group treated with 32% phosphoric acid showed lower shear bond strength than that of the group treated according to the instruction of manufacture but there was no statistical significance. 3. As a result of observation under SEM, the fracture pattern was a mixture of cohesive and adhesive failure in group 1, and there was more adhesive failure in group 2, and in group 3 and 4 there was cohesive failure of material or tooth structure. From the results above Dyract showed shear bond strength levels between resin and resin -modified glass ionomer but Compoglass showed much lower shear bond strength than that of resin-modified glass ionomer thus indicating that even though they are the same type of material they show evident differences in physical properties. And it is thought that the treatment of dentin surface with phosphoric acid did not increase the shear bond strength, unlike enamel.

• 대한소아치과학회지
• /
• 제25권1호
• /
• pp.103-115
• /
• 1998

Adhesion of composite resin to tooth structure has been of tremendous signgicance in clinical dentistry. Due to the lack of adhesion between composite restorative resins and enamel and dentin, microleakage occurs at the tooth/restoration interface. This may lead to discoloration, secondary caries, marginal breakdown, postoperative sensitivity, and even pulpal pathology. According to extensive use of composite resin, every effort on improving bonding strength and reducing microleakage between a tooth and composite resin has been continued. This study was conducted to determine the difference in microleakage in enamel and dentin treated with air-abrasion, acid etching and combination when restored with composite resin. Class V cavities were prepared on 30 premolars. The specimens were divided into following groups. group 1:air-abrasion+Scotchbond Multi-purpose group 4 :air-abrasion+All-Bond 2 group 2:acid etching+Scotchbond Multi-purpose group 5 :acid etching+All-Bond 2 group 3:combination+Scotchbond Multi-purpose group 6 :combination+All-Bond 2 #combination:air-abrasion + acid etching The specimens were filled with Z-100 after application of Scotchbond Multi-purpose and All-Bond 2. Thermocycling was conducted by alternately dipping the specimens in $5^{\circ}C$ and $55^{\circ}C$ water for 30 seconds 500 times. 1% methylene blue was applied and the specimens were left for 24 hours at $37^{\circ}C$. After washing out the dye, the tooth was sectioned buccolingually along the axis. The sectioned surface was observed with stereoscope for dye penetration. The author has measured the microleakage in teeth prepared with air-abrasion, acid ethching and combination to study the difference in microleakage following different methods of tooth surface treatment and has come to following results. 1. In comparing microleakage between groups, group 1 and 4 showed statistically significant difference from group 2, 3, 5 and 6(p<0.05). There was no significant difference among group 2, 3, 5, 6(p>0.05) nor between group 1 and 4(p>0.05). 2. In comparing microleakage among tooth surface treatment methods, Air-abrasion group showed significantly more microleakage than acid etching group and combination(airabrasion + acid etching) group(p<0.05). Combination(acid etching+air-abrasion)group tended to show lesser microleakage than acid etching group, but this was not statistically significant(p>0.05). 3. In comparing microleakage between bonding agents, there was no statistically significant difference between Scotch bond Multi-purpose and All-Bond 2(p>0.05).

• 대한소아치과학회지
• /
• 제36권1호
• /
• pp.38-45
• /
• 2009

본 연구는 상품화된 10% CPP-ACP 크림 (Tooth mousse, GC Co., Japan)이 0.05 % NaF 불소 용액 매일 양치법을 대체할 수 있는지 알아보기 위하여, 인공 탈회 병소를 가진 우치 법랑질에 대해 10일간 위 두 가지 방법 단독 혹은 복합 사용의 재광화 효과를 비교하였다. 0.1% thymol 용액에 냉장 보관한 소의 치아를 교정용 레진 (Orthodotic resin, Dentsply international Inc., USA)에매몰한 후 탈회 용액에 96시간 보관하였고, 총 60개의 시편을 5개의 군으로 나누었다; 비처치군 (1군), 0.05% NaF 용액 1분 (2군), Tooth mousse 3분 (3군), 0.05% NaF 용액 1분 처리 후 Tooth mousse 3분 (4군), Tooth mousse 3분 처리 후 0.05% NaF 용액 1분(5군). 재광화 정도는 10일간의 시편 처리 전 후의 Vickers hardness number를 측정하여 비교하였으며, 연구 결과는 다음과 같다. 1. 각 군에서 시편 처리 전후의 표면경도를 paired t-test를 이용하여 비교분석한 결과, 3, 4, 5 군에서만 유의할만한 표면 경도 증가가 나타났다(P < 0.05). 2. 각 군별로 평균 표면 경도 증가량은 5 > 4 > 3 > 2 > 1 군 순이었고, 각 군의 표면경도 증가량을 one-way ANOVA test로 비교분석한 후 Duncan test로 사후 검정한 결과, 4, 5 군은 1, 2, 3 군과 유의할만한 표면경도 증가를 보였으며 (P < 0.05), 다른 군들 간에는 유의할만한 차이를 보이지 않았다. 3. Tooth mousse를 우치에 10일간 적용시킨 결과 0.05% NaF 용액보다 더 많은 표면경도 변화량을 나타냈지만, 통계학적으로 유의할만한 차이는 없었다. 이상의 결과에서 Tooth mousse 사용은 불소 양치가 용이하지 않은 환자들에게 양호한 대체 방안이 될 것으로 사료되며, 또한 불소 적용시 Tooth mousse를 복합 사용하는 것이 추천될 수 있으리라 사료된다.

• 치위생과학회지
• /
• 제17권4호
• /
• pp.352-357
• /
• 2017

액상소화제의 법랑질 부식능을 알아보기 위하여 마트에서 쉽게 구입할 수 있는 2종의 액상소화제와 약국에서 판매하는 1종의 액상소화제 그리고 대조군으로 생수를 선정하였다. 음료의 pH와 적정산도를 측정하고, 시편을 제작하여 음료에 1, 3, 5, 10, 15, 30분을 침지한 후 나타나는 양상을 표면 미세 경도계로 측정하여 다음과 같은 결론을 얻었다. 대조군인 생수를 제외한 모든 액상소화제의 pH가 4.0 이하로 나타났으며 위청수에서 $2.93{\pm}0.00$으로 가장 낮았다. pH 5.5로 변환하는 데 필요한 적정산도 또한 위청수에서 1.27 ml로 가장 높게 나타났다. 모든 액상소화제에서 침지시간이 증가함에 따라 표면경도가 감소하였으며 음료 30분 처리 후 표면 경도값은 위청수에서 $207.80{\pm}15.52$ VHN으로 가장 낮았고, 까스활명수 $216.86{\pm}4.01$, 생록천 $223.28{\pm}9.56$ 순이었다. 실험에 사용된 모든 액상소화제는 치아 법랑질에 부식을 유발하였으며, 음료처리 후에 pH가 가장 낮고 적정산도가 가장 높은 위청수에서 가장 낮은 표면 경도 값을 보여 실험에 사용된 액상소화제 중 가장 많은 법랑질 부식을 유발하였다. 따라서 액상소화제의 섭취는 법랑질표면경도를 감소시켜 치아 부식을 유발할 수 있으므로 이에 대한 대처방안이 마련되어야 할 것이다.