• 한국의류산업학회지
• /
• 제10권3호
• /
• pp.389-393
• /
• 2008

The purpose of this study is to provide beauticians with the fundamental material for them to use effectively heat permanent wave and satisfy their customers. It carried out an experiment with hair of a woman in her late twenties to investigate the change of physical and morphologic characteristics by its water content when performing heat permanent wave. It evaluated the water content as 0g, 1g, 2g, 3g and 4g respectively when performing the heat permanent wave on hair, then it compared and observed the wave type, tensile strength and elongation for its physical change also observed the morphologic change by scanning electronic microscope and transmission electronic microscope. The result of experiment on the physical specificity revealed that the wave was the most ideal when the water content was 2 g. The material with much water content made wave but the result was not satisfied. In the case of hair with water content of nearly 0g didn't make wave. In terms of tensile strength and elongation, the tensile strength was generally reduced as hair was damaged, on the contrary, the elongation was increased. It observed the change of morphologic characteristic and got the result that the damage on hair cuticle was deepen as its water content was decreased. It also showed the result that damage happened on hair cuticle more than hair cortex with the observation of fine structure on hair section by transmission electronic microscope. Generally chemical treatment damaged hair. Under consideration of this aspect, the ultimate goal of this thesis is to minimize the damage of hair caused by chemical treatment and get the satisfaction on the hair style. The result of experiment presented that the hair showed the best result when its water content was 2 g.

• 한국음향학회지
• /
• 제19권7호
• /
• pp.15-22
• /
• 2000

본 연구에서는 수중표적의 반사신호를 재현하기 위한 공간적 하이라이트 분포처리 알고리듬을 제안한다. 제안된 알고리듬은 입사되는 핑펄스의 각도에 따라 가변적인 불연속 하이라이트와 표적내부 및 특정위치의 하이라이트를 신호 입사각에 따라 분포시켜 합성한다. 완성된 UTAHID 모델은 핑펄스의 입사각도 및 펄스폭에 따라 첨두치 표적강도, 에너지 표적강도, 에코신장효과, 표적 시간분산 손실 및 포락선의 불규칙성 등을 각종 모의실험으로 타당성을 확인하였으며, 이는 능동소나의 표적 반사신호 합성에 관련된 각종 실제 시스템에 효율적으로 적용될 수 있다.

• 한국주조공학회지
• /
• 제18권6호
• /
• pp.570-577
• /
• 1998

An investigation has been conducted to describe solidification characteristics in Sn-Zn binary system and Sn-Zn-Ag ternary system added by Ag produced by the continuous casting process using heated mold as a basic study for developing Pb-free solder materials. To obtain the continuous casting rods with mirror surface and near net shape at higher casting speed, water flow rates must be increased and mold temperature must be lowered. However, surface tearing in the casting rods occured at lower continuous casting speed while break out occured at higher continuous casting speed even if optimum conditions such as water flow rate and heated mold temperature are determined. Primary ${\alpha}Sn$ and eutectic structure in unidirectioally solidified Sn-Zn alloys were finer with increased casting speed. But, directionality may not be expected for primary Zn in hypereutectic Sn-Zn alloy. It was found that the addition of $0.2{\sim}0.8%$ Ag promoted the growth of primary ${\alpha}Sn$ dendrites. The changes of tensile strength and elongation in Sn-Zn binary alloys were not observed while the increase of tensile strength and the decrease of elongation in Sn-Zn-Ag ternary alloys were observed with increased casting speed.

• Macromolecular Research
• /
• 제14권2호
• /
• pp.187-193
• /
• 2006

Organoclay, was applied as a filler, in place of carbon black and silica, to a natural rubber (NR)/butadiene rubber (BR) blend. A compounding method was used to disperse and separate the layered silicates. The effect of a coupling agent on the vulcanizates was evaluated using both the silica and organoclay filled compounds. After the compounding processes were completed, the XRD diffraction peaks disappeared, but then reappeared after vulcanization. The scorch times for the organoclay-filled compounds were very short compared to those for carbon black and silica-filled compounds. The organoclay-filled compounds showed high values of tensile strength, modulus, tear energy, and elongation at the break. When ranked by viscosity, the compounds appeared in the following order: silica > silica (Si-69) > organoclay > organoclay (Si-69) > carbon black. Fractional hysteresis, tensile set, and wear rates were very consistent with the viscosity of the vulcanizates. The Si 69 coupling agent increased reversion resistance, the maximum torque values in the ODR, modulus, and wear resistance, but decreased elongation at the break, fractional hysteresis, and tension set of the vulcanizates.

• 한국주조공학회지
• /
• 제40권3호
• /
• pp.61-65
• /
• 2020

Rheo-diecasting with stirring has been used in many material industries. As the 4th Industrial Revolution approaches the world, eco-friendly high-strength and light-weight materials become more important. Casting methods have been studied and used for aluminum-alloy automobile parts. This study carried out the effect analysis of the micro-structure and mechanical properties, such as yield/ultimate tensile strength, elongation, and hardness, of A356 using the 6-pole EMS (electro-magnetic stirring) casting process with a high electromagnetic force. As a result, the hardness and elongation of the A356 after T6 heat-treatment show a significant improvement, respectively, by 20% and 50%.

• Asian-Australasian Journal of Animal Sciences
• /
• 제19권7호
• /
• pp.953-957
• /
• 2006

The eukaryotic elongation factor 1 A (EEF1A) participates in protein synthesis by forming the eEF1A GTP tRNA complex to deliver aminoacyl-tRNA to the A site of ribosomes. This study described cDNA sequences and partial genomic structure of porcine EEF1A1. The porcine EEF1A1 gene encoded a protein with 462 amino acids, which shared complete homology with human, chimpanzee and dog. The temporal expression pattern showed the diversity of EEF1A1 level in mRNA was relatively minor in prenatal embryo skeletal muscle, however, the expression decreased during aging after birth in skeletal muscle of the Chinese Tongcheng pig. The spatial expression patterns indicated that the gene expressed in skeletal muscle, heart, lung, liver, kidney, fat and spleen. In addition, we assigned the gene to porcine chromosome 1 using a radiation hybrid panel.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.193-197
• /
• 2002

In this study, the casting/forging process was applied to the Shift-Fork, a manual transmission part of automobiles. In the casting experiments, the effects of additives, Sr, Ti＋B and Mg, on the mechanical properties and the microstructure of a cast preform were investigated. When 0.03% Sr were added into the molten aluminum alloy, the finest silicon-structure was observed in the cast preform and the highest tensile strength and elongation accomplished. And when 0.2% Ti＋B were added into the molten Al-Si alloy, the highest values of tensile strength were obtained. The maximum hardness was in case of 0.2% Mg. In the forging experiment, it was confirmed that the optimal configuration of the cast preform could be predicted by FE analysis. To minimize the cost as the press size, the compact shape of preform was proposed to reduce the volume of flash. The modification of shape in designing preform was performed to attain a satisfactory performance in the areas where the mechanical strength were more required. By using FVM(Finite Volume Method) software, it was verified that a proposed casting design was available. To identify the relationship between effective strain and mechanical properties of the final forged product, the compression test was performed. As the result, the tensile strength and elongation of a cast preform were much higher than before forging. The minimum forging temperature was found 40$0^{\circ}C$ to save heating time.

• 한국의류학회지
• /
• 제28권9_10호
• /
• pp.1282-1291
• /
• 2004

Kenaf was cultivated and harvested in large quantity in Cheju Island and Chinju, Kyungsangnamdo. It was chemically rotted with 3% NaOH for 60 minutes at 100$^{\circ}C$, neutralized using 1% acetic acid, washed and dried, and obtained 40kg of dry kenaf fiber. Kenaf 15/rayon 85, flax 15/rayon 85, and rayon 100% yam was spun and the physical characteristics were measured. Plain weave and twill weave fabrics were made using each of the above yarns as the filling yam. Cotton 100% yam was used as the warp yam in all fabrics. Kenaf/rayon blend yarns were higher in tenacity and elongation, lower in yam uniformity, higher in the number of nep than the flax/rayon blended yams. Kenaf/rayon blend fabric had higher tenacity and elongation compared to the flax/rayon blend fabric Kenaf/rayon blend fabric was most stiff in both plain weave and twill weave fabrics whereas drape characteristics was dependent upon the fabric structure of the kenaf/rayon blend and flax/rayon blend. There were little differences between the kenaf/rayon blend fabric and the flax/rayon blend fabric in the Kawabata physical measurements and the PHVs. The only drawback of kenaf fiber was it's surface roughness and it is expected that it can be improved by enzyme retting and mechanical bundle separation.

• 열처리공학회지
• /
• 제5권2호
• /
• pp.111-121
• /
• 1992

For the purpose of investigating the effect of austenitizing temperatures on the mechanical properties of 0.23% C-13.6%Cr martensitic stainless steel, tensile properties, hardness, impact value and carbide extraction were examined after changing the austenitizing temperatures and tempering temperatures. The results obtained are summerized as follows. The carbide laminations formed from hot rolling before austenitization could not be eliminated after austenitizing at $950^{\circ}C$. With increasing austenitizing temperature, hardness increased and showed maximum value at $1050^{\circ}C$ and then slightly decreased. With increasing tempering temperature up to $500^{\circ}C$, impact value and elongation appeard to be decreased but hardness showed nearly unchanged at austenitizing temperature of $1150^{\circ}C$ due to the fine $M_7C_3$ carbides precipitation. The abrupt increase in impact value, hardness and elongation above the tempering temperature of $500^{\circ}C$ appeared to change in carbide structure from fine $M_7C_3$ to coarse $M_{23}C_6$.

• Journal of Plant Biology
• /
• 제22권1_2호
• /
• pp.35-43
• /
• 1979

The present investigation has been made to study the deficiency symptoms of boron on the formation of cell wall and the development of the individual components of the orchid cell wall. Analytical samples were taken from two sources; one from the individual orchid plants started from an apical meristem culture followed by the generation of the protocorm-like body which was developed into a plant, the other from the plant cultivated in water for 30 days. The amount of boron in the cultrues were controlled and the deficiency symptoms were observed under theelectron microscope, optical microscope with samples taken from the zones of elongation of leaves and compared the dry weight of cell walls and finally the various fractions of the cell wall components. The following results were obtained: (1) The growth of roots and leaves was hampered in the boron deficient plants. (2) In the boron-deficient leaves a severe necrosis and cracks were developed in the tissue of zone of elongation besides the decrease in growth. (3) under the electorn microscope the cell walls of boron-deficient plants showed rough undulated structures unlike the smooth control cell walls. (4) the dry weight of total cells and cell walls of boron deficient plants were higher than the control plants. (5) In the boron deficient plant the amout of pectin and hemicellulose isolated from cell walls were higher and the amount of protein was lower than the controlled plots.