• JSTS:Journal of Semiconductor Technology and Science
• /
• 제17권3호
• /
• pp.425-437
• /
• 2017

For efficient hardware (HW) implementation of elliptic curve cryptography (ECC), various sub-modules for the underlying finite field operations should be implemented efficiently. Among these sub-modules, modular inversion (MI) requires the most computation; therefore, its performance might be a dominant factor of the overall performance of an ECC module. To determine the most efficient MI algorithm for an HW ECC module, we implement various classes of MI algorithms and analyze their performance. In contrast to the common belief in previous research, our results show that the right-shift binary inversion (RS) algorithm performs well when implemented in hardware. In addition, we present optimization methods to reduce the area overhead and improve the speed of the RS algorithm. By applying these methods, we propose a new RS-variant that is both fast and compact. The proposed MI module is more than twice as fast as the other two classes of MI: shifting Euclidean (SE) and left-shift binary inversion (LS) algorithms. It consumes only 15% more area and even 5% less area than SE and LS, respectively. Finally, we show that how our new method can be applied to optimize an HW ECC module.

• Current Photovoltaic Research
• /
• 제6권2호
• /
• pp.62-67
• /
• 2018

Multi-wire busbar-type bifacial n-type Si solar cells have been used for the fabrication of monofacial and bifacial photovoltaic (PV) module, where bifacial module was equipped with transparent backsheet while monofacial module was prepared using white backsheet. The comparison of six-day accumulated power production obtained from outdoor test under gray cement ground conditions using 60cell monofacial and bifacial PV modules suggested the bifacial gain of over 20% could be achieved. Furthermore, the outdoor evaluation tests of bifacial modules with different ground conditions such as cement (reference), green paint, white paint and green artificial grass, were performed. It turned out white paint showed the best albedo and thus the highest power production, while green paint and artificial grass showed less power generation than cement ground.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.1115-1119
• /
• 2005

The paper proposes the elastic modulus evaluation technique of a cantilever beam by vibration analysis based on time-average electronic speckle pattern interferometry (TA-ESPI) with non-contact and nondestructive and Euler-Bernoulli equation. General approaches for the measurement of elastic modulus of thin film are Nano indentation test, Bulge test and Micro-tensile test and so on. They each have strength and weakness in the preparation of test specimen and the analysis of experimental result. ESPI has been developed as a common measurement method for vibration mode visualization and surface displacement. Whole-field vibration mode shape (surface displacement distribution) at a resonance frequency can be visualized by ESPI. And the maximum surface displacement distribution from ESPI is a clue to find the resonance frequency at each vibration mode shape. And the elastic modules of test material can be easily estimated from the measured resonance frequency and Euler-Bernoulli equation. The TA-ESPI vibration analysis technique is able to give the elastic modulus of materials through the simple processing of preparation and analysis.

• 한국전자통신학회논문지
• /
• 제6권4호
• /
• pp.589-594
• /
• 2011

스마트 폰 또는 홈 네트워크 기술은 지속적으로 부가가치를 창출할 수 있는 기술로, 삶의 질을 한층 더 높게 만들어 준다. 본 논문에서는 스마트 폰을 통해 스마트 홈을 제어 하는 시스템을 설계 및 구현하였다. 구현된 스마트 홈 시스템은 홈 노드 구조물, 원격 스마트 응용 시스템, 홈 서버 제어 시스템으로 구성된다. 홈 노드 구조물은 침입 감지, 가스 검출 및 밸브 제어, 도어 락, 자동커튼, 환풍기 제어 및 On/Off 제어 모듈로 구성되어 있으며 모듈들은 홈 서버에 의해서 제어 된다. 홈 서버는 사용자가 직접 제어할 수 있는 사용자 인터페이스와 스마트 폰을 이용하여 원격 제어할 수 있는 원격 인터페이스를 제공함으로써 언제 어디서나 편리하게 홈 자동제어시스템을 제어할 수 있다.

• 한국전기전자재료학회논문지
• /
• 제27권9호
• /
• pp.594-599
• /
• 2014

The heat dissipation conditions of high-power 5 watt LEDs-based searchlight modules were optimized with varying LED bar'shape, materials, and ambient temperature. The LED junction temperature was estimated by using Computational Fluid Dynamics simulation. The optimal heat dissipation conditions were found as follows; LED bar' shape: L=80 mm, W=4 mm, t=10 mm, copper material, LED junction temperature of $116.6^{\circ}C$, ambient temperature of $50^{\circ}C$, total mass of 184 g, and shadowing area of $320mm^2$. The difference between the junction temperatures of our fabricated and simulated LEDs-based searchlight modules is about $3^{\circ}C$, which confirms the validity of our thermal simulation results.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제3B권1호
• /
• pp.44-51
• /
• 2003

The module UPS can flexibly implement expansion of power system capacities. Further-more, it can be used to build up the parallel redundant system to improve the reliability of power system operation. To realize the module UPS, load sharing without interconnection among parallel connecting modules as well as a small scale and lightweight topology is necessary. In this paper, the three-arm converter/inverter is compared with the general full-bridge and half-bridge topology from a practical point of view and chosen as the module UPS topology. The switching control approaches based on a pulse width modulation of the converter and inverter of the system are presented independently. The frequency and voltage droop method is applied to parallel operation control to achieve load sharing. Two prototype 3㎸A modules are designed and implemented to confirm the effectiveness of the pro-posed approaches. Experimental results show that the three-arm UPS system has a high power factor, a low distortion of output voltage and input current, and good load sharing characteristics.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2003년도 하계종합학술대회 논문집 II
• /
• pp.1125-1128
• /
• 2003

This paper presents the design method of a Colpitts type oscillator with coplanar waveguide(CPW) structures in the range of Ka-band frequency for transmitter and receiver modules. Series short stubs of CPW patterns provide inductances and capacitances in the range of Ka-band which can be expressed as a CLC-$\pi$ equivalent circuit. The experimentation has employed ro4003 substrates as a CPW substrate which has a dielectric constant of 3.38 and a signal and ground space of 100um. A method of momentum simulation for the CPW patterns has performed with an ADS software tool of Hewlett-Packard Corp. Inductance and capacitance circuits of a Colpitts oscillator was interconnected to a MESFET with CPW bend structures of including the input and output impedance matching circuits of the active transistor. Circuit parameters for impedance matching were determined through the network conversion to the equivalent length of CPW transmission lines by using T-network 1 $\pi$-network conversion circuit. A Colpitts oscillator was fabricated on the substrate of a area of 8.5mm x 17.4mm with a MESFET of Fujitsu FMM5704X and CPW series short stubs. The design suggested the possibility of realizing oscillators on a planar surface for the wireless system of tansmitter and receiver modules in the frequency range of 30GHz

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.829-832
• /
• 2000

This paper describes a research work of developing a computer-aided design of product with bending and piercing for progressive working. An approach to the CAD system is based on the knowledge-based rules. Knowledge fur the CAD system is formulated from plasticity theories, experimental results and the empirical knowledge of field experts. The system has been written in AutoLISP on the AutoCAD with a personal computer and is composed of three main modules, which are input and shape treatment, flat pattern layout and strip layout module. Based on knowledge-based rules, the system is designed by considering several factors, such as radius and angle of bend, material and thickness of product, complexities of blank geometry and punch profile, bending sequence, and availability of press. Strip layout drawing automatically generated by piercing with punch profiles divided into for external area is simulated in 3-D graphic forms, including bending sequences for the product with piercing and bending. Results obtained using the modules enable the manufacturer of electronic products to be more efficient in this field.

• 한국전자통신학회논문지
• /
• 제7권2호
• /
• pp.213-219
• /
• 2012

본 논문은 외부 영향에 의하여 고속 정보시스템의 모듈사이에서 발생되는 전송잡음과 왜곡신호에 대한 신호 보전의 방법에 대하여 제안하였다. 고속 전송선로의 왜곡효과를 제거하기 위하여 전송선로 임피던스 정합에 의한 신호보전(signal integrity)은 고속 동작에 따른 전송선로효과 발생조건을 ADS로 모델링한 후 최적의 임피던스 정합을 단선 및 차동인터페이스 방식으로 구분하였다. 실험한 결과, 고속 정보통신시스템에 따르는 신호지연을 고려하여 최적의 단자 임피던스 값을 정합시켜 고속 신호의 최적 보전이 가능함을 보여 주었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 유기절연재료 전자세라믹 방전플라즈마 일렉트렛트 및 응용기술
• /
• pp.15-17
• /
• 2002

Leakage inductance and temperature rise are two of the more impotent problems facing the magnetic core technology of today's high frequency transformers. Excessive leakage inductance increases the stress on the switching transistors and limits the duty-cycle, and excessive temperature rise can lead the design limitation of high frequency transformer with high current. The flat transformer technology provides a very good solution to the problems of leakage inductance and thermal management for high frequency power. The critical magnetic components and windings are optimized and packaged within a completely assembled module. The turns ratio in a flat transformer is determined as the product of the number of elements or modules times the number of primary turns. The leakage inductance increase proportionately to the number of elements, but since it is reduced as the square of the turns, the net reduction can be very significant. The flat transformer modules use cores which have no gap. This eliminates fringing fluxes and stray flux outside of the core. The secondary windings are formed of flat metal and are bonded to the inside surface of the core. The secondary winding thus surrounds the primary winding, so nearly all of the flux is captured.