• Journal of Electrical Engineering and Technology
• /
• v.13 no.3
• /
• pp.1251-1264
• /
• 2018

The systematic and effective design method of a Class-D current-source resonant inverter for use in an induction cooker with zero-ripple line current is presented. The design procedure is based on the principle of the Class-D current-source resonant inverter with a simplified load network model that is a parallel equivalent circuit. An induction load characterization is obtained from a large-signal excitation test-bench based on parallel load network, which is the key to an accurate design for the induction cooker system. Accordingly, the proposed scheme provides a systematic, precise, and feasible solution than the existing design method based on series-parallel load network under low-signal excitation. Moreover, a zero-ripple condition of utility-line input current is naturally preserved without any extra circuit or control. Meanwhile, a differential-mode input electromagnetic interference (EMI) filter can be eliminated, high power quality in utility-line can be obtained, and a standard-recovery diode of bridge-rectifier can be employed. The step-by-step design procedure explained with design example. The devices stress and power loss analysis of induction cooker with a parallel load network under large-signal excitation are described. A 2,500-W laboratory prototype was developed for $220-V_{rms}/50-Hz$ utility-line to verify the theoretical analysis. An efficiency of the prototype is 96% at full load.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.16 no.3
• /
• pp.29-36
• /
• 2002

Recently, power quality problems in AC high-Speed Railway system have been raised, because heavy train and its higher speed are required in addition to new control system by using the Electronic devices. The installation/operation of the Series Capacitor(SC) has been only a device far voltage drop in power system up to now. However, the sufficient effectiveness of compensating In voltage drop has not been proved yet because of technical limitationf SC, and harmonic resonance is attracting a attention as one of new issues. Several problems are expected such as vocational problems of a traction substation, and overloading caused by a new construction of electric railway and the in transport. Therefore, extension of power feeding the fault in the traction substation should be also considered. So this paper represents the application of TSC-SVC on the electric railway power feeding system as a device of voltage compensation, and the simulations are executed through PSCAD/EMTDC.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.17 no.4
• /
• pp.485-491
• /
• 2014

An Antenna & RF system for a fly-away satcom terminal application on ka-band is presented in this paper. The Fly-away satellite terminal can be moved and operated by two person and adapt automatic satellite tracking system in order to decrease the tracking time. Additionally, for low-power consumption, compact size and light-weight, a dual reflector antenna is constructed using dual-offset gregorian antenna structure. For minimize weight, the reflector of the antenna is made of Magnesium. For low-power consumption and light-weight, the pHEMT MMIC compound devices is utilized. The Electronic Band-Gap(EBG) Low-Pass Filter(LPF) is designed for harmonic rejection. In the receiving part, Low-Noise Block converter(LNB) structure is designed for compact and lightweight. In this paper, fly-away satcom terminal with low-power consumption, compact size and light-weight is described with antenna system and RF system performances. Through the experimentation, fly-away terminal's EIRP is more than 50dBW, G/T is more than $17dB/^{\circ}K$.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.05a
• /
• pp.934-937
• /
• 2010

In this paper, we did pursue the embodiment of a mouse pointing system which help the handicapped and people of not familiar with using electronics use electronic devices easily. Speech Recognition and 3-axis acceleration sensors in conjunction with a headset, a new mouse pointing system is constructed. We used speaker dependent system module which are generating the BCD code by recognizing human voices because it has high recognition rate rather than speaker independent system. Head-set mouse system is organized by 3-axis accelerometer, sound recognition module and TMS320F2812 processor. The main controller, TMS320F2812 DSP-processor is communicated with main computer by using SCI communications. The system is operated by Visual Basic in PC.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.12
• /
• pp.2952-2959
• /
• 2013

In this paper, a smart meter applying the international communication protocols has been developed. A smart meter requires communication protocols for two-way communication and control technology, registration and deregistration of electronic devices between electric power suppliers to exchange data. Standardization for communication protocols of a smart meter has been proceeding both in the US and Europe. The smart meter developed in this paper applied ANSI C12.22 as a communication protocol which is a north american standard. A smart meter should also provide the electric consuming information and electricity charge information to the customer in real time. Thus, the customer can behave the demand response based on this information. In this paper, the measured electricity from the smart meter is reported to the customer, and IHD(In Home Display) implemented with the windows software presents the reported real time data.

• Annual Conference of KIPS
• /
• 2018.10a
• /
• pp.984-987
• /
• 2018

In an Internet of Thing (IoT) environment, entities with different attributes and capacities are going to be connected in a highly connected fashion. Specifically, not only the mechanical and electronic devices but also other entities such as people, locations and applications are connected to each other. Understanding and managing these connections play an important role for businesses, which identify opportunities for new IoT services. Traditional approach for storing and querying IoT data is used of a relational database management system (RDMS) such as MySQL or MSSQL. However, using RDMS is not flexible and sufficient for handling heterogeneous IoT data because these data have deeply complex relationships which require nested queries and complex joins on multiple tables. In this paper, we propose a graph model for constructing a graph database of heterogeneous IoT data. Graph databases are purposely-built to store highly connected data with nodes representing entities and edges representing the relationships between these entities. Our model fuses social graph, spatial graph, and things graph, and incorporates the relationships among them. We then present a case study which applies our model for representing data from a Smart Campus using Neo4J platform. Through the results of querying to answer real questions in Smart Campus management, we show the viability of our model.

• International Journal of Highway Engineering
• /
• v.15 no.6
• /
• pp.41-47
• /
• 2013

PURPOSES : The purpose of this study is about noise which is generated from roads and is consist of irregular frequency variation from low frequency to various band. The existing methods of noise reduction are sound barrier that uses insulation material and absorbing material or have applied passive technology of noise reduction by devices. The total frequency band is needed to apply active noise control. METHODS : In this study applies to the field of road traffic environment, signal processing controller and various analog signal input/output, the amplifier module is based on parallel-core embedded processor designed. DSP performs the control algorithm of the road traffic noise. Noise sources in the open space performance of evaluation were applied. In this study, controller of active signal processor was designed based on the module of audio input/output and main controller of embedded process. The controller of active signal processor operates noise reduction algorithm and performance tests of noise reduction in inside and outside environment were executed. RESULTS : The signal processing controller with OMAP-L137 parallel-core processors as the center, DSP processors in the active control operations dealt with quickly. To maximize the operation speed of an object and ARM processor is external function keys and display for functions and evaluating the performance management system was designed for the purpose of the interface. Therefore the reduction of road traffic noise has established an electronic controller-based noise reduction. CONCLUSIONS : It is shown that noise reduction is effective in the case of pour tonal sound and complex tonal sound below 500Hz by appling to Fx-LMS.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.80-80
• /
• 2010

Graphene has attracted tremendous attention for the last a few years due to it fascinating electrical, mechanical, and chemical properties. Up to now, several methods have been developed exclusively to prepare graphene, which include micromechanical cleavage, polycrystalline Ni employing chemical vapor deposition technique, solvent thermal reaction, thermal desorption of Si from SiC substrates, chemical routes via graphite intercalation compounds or graphite oxide. In particular, polycrystalline Ni foil and conventional chemical vapor deposition system have been widely used for synthesis of large-area graphene. [1-3] In this study, synthesis of mono-layer graphene on a Ni foil, the mixing ratio of hydrocarbon ($CH_4$) gas to hydrogen gas, microwave power, and growth time were systemically optimized. It is possible to synthesize a graphene at relatively lower temperature ($500^{\circ}C$) than those (${\sim}1000^{\circ}C$) of previous results. Also, we could control the number of graphene according to the growth conditions. The structural features such as surface morphology, crystallinity and number of layer were investigated by scanning electron microscopy (SEM) and atomic force microscopy (AFM), transmission electron microscopy (TEM) and resonant Raman spectroscopy with 514 nm excitation wavelength. We believe that our approach for the synthesis of mono-layer graphene may be potentially useful for the development of many electronic devices.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.297.2-297.2
• /
• 2013

Scavenging electricity from wasteful energy resources is currently an important issue and piezoelectric nanogenerators (NGs) based on zinc oxide (ZnO) are promising energy harvesters that can be adapted to various portable, wearable, self-powered electronic devices. Although ZnO has several advantages for NGs, the piezoelectric semiconductor material ZnO generate an intrinsic piezoelectric potential of a few volts as a result of its mechanical deformation. As grown, ZnO is usually n-type, a property that was historically ascribed to native defects. Oxygen vacancies (Vo) that work as donors exist in ZnO thin film and usually screen some parts of the piezoelectric potential. Consequently, the ZnO NGs' piezoelectric power cannot reach to its theoretical value, and thus decreasing the effect from Vo is essential. In the present study, c-axis oriented insulator-like sputtered ZnO thin films were grown in various temperatures to fabricate an optimized nanogenerator (NGs). The purity and crystalinity of ZnO were investigated with photoluminescence (PL). Moreover, by introducing a p-type polymer usually used in organic solar cell, it was discussed how piezoelectric passivation effect works in ZnO thin films having different types of defects. Prepared ZnO thin films have both Zn vacancies (accepter like) and oxygen vacancies (donor like). It generates output voltage 20 time lager than n-type dominant semiconducting ZnO thin film without p-type polymer conjugating. The enhancement is due to the internal accepter like point defects, zinc vacancies (VZn). When the more VZn concentration increases, the more chances to prevent piezoelectric potential screening effects are occurred, consequently, the output voltage is enhanced. Moreover, by passivating remained effective oxygen vacancies by p-type polymers, we demonstrated further power enhancement.

• Korean Journal of Materials Research
• /
• v.22 no.7
• /
• pp.335-341
• /
• 2012

Recently, the demand for the miniaturization of printed circuit boards has been increasing, as electronic devices have been sharply downsized. Conventional multi-layered PCBs are limited in terms their use with higher packaging densities. Therefore, a build-up process has been adopted as a new multi-layered PCB manufacturing process. In this process, via-holes are used to connect each conductive layer. After the connection of the interlayers created by electro copper plating, the via-holes are filled with a conductive paste. In this study, a desmear treatment, electroless plating and electroplating were carried out to investigate the optimum processing conditions for Cu via filling on a PCB. The desmear treatment involved swelling, etching, reduction, and an acid dip. A seed layer was formed on the via surface by electroless Cu plating. For Cu via filling, the electroplating of Cu from an acid sulfate bath containing typical additives such as PEG(polyethylene glycol), chloride ions, bis-(3-sodiumsulfopropyl disulfide) (SPS), and Janus Green B(JGB) was carried out. The desmear treatment clearly removes laser drilling residue and improves the surface roughness, which is necessary to ensure good adhesion of the Cu. A homogeneous and thick Cu seed layer was deposited on the samples after the desmear treatment. The 2,2'-Dipyridyl additive significantly improves the seed layer quality. SPS, PEG, and JGB additives are necessary to ensure defect-free bottom-up super filling.