• Transactions of the Society of Information Storage Systems
• /
• v.1 no.1
• /
• pp.108-114
• /
• 2005

The generation of fine relics of suspensions is a significant interest as it holds the key to the fabrication of electronic devices. These processes offer opportunities for miniaturization of multilayer circuits, for production of functionally graded materials, ordered composites and far small complex-shaped components. Some novel printing methods of depositing ceramic and metal droplets were suggested in recent years. In an electro-hydrodynamic printing, the metallic capillary nozzle can be raised to several kilovolts with respect to the infinite ground plate or pin-type electrode positioned a few millimeters from the nozzle tip. Depending on the electrical and physical properties of the liquid, for a given geometry, it Is possible to generate droplets in any one of three modes, dripping, cone-jet and multi-jet. In this experiment, an alumina suspension flowing through a nozzle was subjected to electro-hydrodynamic printing using pin-type electrodes in the cone-jet mode at different applied voltages. The pin-type electrodes of 1, 100, 1000${\mu}m$ in diameter were used to form fine ceramic patterns onto the substrates. Various feature sizes with applied voltages and electrode diameters were measured. The feature sizes increased with the electrode diameter and applied voltages. The feature size was as fine as $30 {\mu}m$.

• Proceedings of the KOSOMBE Conference
• /
• v.1998 no.11
• /
• pp.127-128
• /
• 1998

It is necessary to maintain constant intravenous (IV) infusion rate. While infusion pump is able to control infusion rate with great accuracy, its rather large size and weight make it difficult for patients to move around. The most commonly used infusion device is gravity IV infusion set with its administration chamber being clamped according to the observed drip rate. In this case it may be easier and more accurate to maintain IV rate to given value if we automate the drip-counting process and tube-clamping work by electronic devices. We calculated volume infusion rate of specific fluid using optical drip rate meter which we had developed. To regulate fluid flow rate, we equipped the rate meter which we had developed with a miniaturized clamping apparatus using DC motor. Also, we Implemented drip detection and clamp control algorithm with PIC16C73 $\mu$-controller (Microchip). This system provides user interface through LCD display and key buttons.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.9
• /
• pp.7-10
• /
• 2010

Recently, roll-to-roll printers are being developed actively by various research teams such as research institutes, universities and companies for the application of printed electronics. The printing methods that are widely used in the roll-to-roll printing equipments are gravure, gravure and flexo, which depend on the inks used and electronic devices produced. In general, a single printing unit of roll-to-roll printing equipment adopts only one printing method and this method is not changeable, which limits the application fields of the developed printing equipments. In this paper, the roll-to-roll printer, in which the printing unit has the novel design concept, is described.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.10
• /
• pp.1123-1130
• /
• 2011

The pattern shape engraved on the gravure printing roll is one of the most important factors influencing ink transfer. This study focuses on the relations between dot geometry engraved on gravure printing roll and the ink transfer during the gravure printing process. The influence of dot width on printed patterns will be demonstrated. Results reveal that as the width of a dot on the printing roll increases, the ink transfer rate also increases. But over a certain size of width, surface uniformity began to recede. Therefore, proper dot geometry on the printing roll should be decided to guarantee good printing quality according to printing conditions and expected performance of the electronic devices.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.10
• /
• pp.1141-1145
• /
• 2011

Recently, there are many issues about R2R printing technique for mass production of electronic devices. Among the various Roll-to-roll based printing techniques such as gravure, off-set, flexo and so on, "Gravure off-set printing technique" has an advantage of higher printing resolution. The printing unit of gravure off-set printing technique usually consists of plate roll, blanket roll and impressure roll whose. Linear velocities should be synchronized each other for fine pattern printing. However, roller's manufacturing error and printing variations such as pringting pressure, printing speed, roll stroke and so on actually affected their synchronization anf thus the quality of fine fattern. In this paper, we analyzed the effective of synchronization error on printing quality. Also, this paper reviews the relative motion with each roll. And, this paper studys the synchronization error about its generation problem.

• Journal of Internet Computing and Services
• /
• v.10 no.4
• /
• pp.213-222
• /
• 2009

IEEE 802.15.3 HR-WPAN is designed to enable wireless connectivity of high-speed, low-power, low-cost multimedia-capable portable consumer electronic devices. For quality of service, the standard specifies the use of TDMA (Time Division Multiple Access). However, during low contention TDMA gives much lower channel utilization and higher delays than CSMA (Carrier Sensing Multiple Access) because in TDMA, a node can transmit only during its scheduled time slots whereas in CSMA, nodes can transmit at any time as long as there is no contention. By mixing CSMA and TDMA, Hybrid MAC becomes more robust to timing failures, time-varying channel conditions, slot assignment failures and topology changes than a stand-alone TDMA.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.147-150
• /
• 2002

A light guide panel is an element of the LCD backlight module that is often used for the display of compact electronic devices. In this study, a laser marking system is proposed to fabricate light guide panel, which can be replaced of other manufacturing methods such as silk printing, stamping, and v-cutting methods. The objectives of this research are the establishment of laser marking system, evaluation of laser marking parameters, understanding marking process, application to PMMA, reliability test and quality inspection. A 50W $CO_2$ laser (CW) was used to perform different experiments in which, the influence of some processing parameters (average power, scanning speed) on the geometry and quality of groove pattern was studied. The width of the etched grooves increases with increasing a laser power and decreasing a scan speed. In order to analyze surface characteristics and optical properties (luminance, uniformity), SEM photography and BM7 (luminance measuring system) were used. As a result, the optimal conditions of the process parameters were determined.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.10
• /
• pp.65-73
• /
• 2009

For mass production of printed electronics in roll-to-roll fashion, precision tension control is important to reduce register errors. Register error should be minimized within several to tens of microns for many electronic devices to be manufactured through printing technology. In order to achieve this goal, tension disturbance must be attenuated before printing process within a certain range. In this paper, a certain tension range which allows maintaining register error within 10 micron was defined with specific operating conditions. A LQG controller was proposed instead of the conventional PI controller for precision tension control using a multivariable feedback. A guideline to determine design parameters for calculating LQ gain was proposed. The proposed LQG controller was compared to both PI controller and LQ regulator with white noise by numerical simulations. Results showed that the proposed LQG controller was effective for attenuating tension disturbance with white noise.

• Transactions of the KSME C: Technology and Education
• /
• v.5 no.1
• /
• pp.1-6
• /
• 2017

From early simple bulky detectors to show the existence of some specific material, sensor has been developed to miniature smart sensors embedded signal capabilities with a help of nano/micro engineering such as innovative nano materials and semiconductor process technologies. Due to recently fast sales of smart phones with simple telephone function plus many sensors, internet accessing capabilities, easy user downloadable "app" softwares, smart sensor industry market has expanded very fast. If driver-less cars, wearable electronic devices and smart robots will be introduced into market in near future, development of many various smart sensors will be needed.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.858-861
• /
• 2006

In this paper, a study on the noise reduction in a mobile fuel cell system is presented. Among various fuel cell systems around 20W capacities designed for mobile electronic devices, the active direct methanol fuel cell (DMFC) systems have been recently developed. In such systems, the primary noise source is the air pump which provides sufficient air flow ($5{\sim}6$ liter/min) for electrochemical reaction with methanol fuel while the noise contributions from other auxiliary parts are relatively small. Especially, the discrete noise tones generated by the air pump are dominant and those frequency peaks related to the rotor harmonics are needed to be suppressed by a silencer. Therefore. the Herschel/Quinke (HQ) tubes, which use the out-of-phase cancellation of acoustic waves propagating through direct and indirect pathways, are applied to the inlet of the air pump. Performance of noise reduction with HQ silencer is analytically estimated by calculating the transmission. The length and number of thin HQ tubes are optimized to decrease the radiated noise. As a result, the sound pressure level could be successfully reduced by about 10 dB after applying three serially connected HQ tubes.