• Journal of Korean Vacuum Science & Technology
• /
• v.6 no.2
• /
• pp.71-75
• /
• 2002

GaAs polycrystalline thin films with good performance were prepared on conducting glass by hot wall epitaxy (HWE), which were used for solar cell. Electron probe micro-analyzer (EPMA) was applied for the composition, morphology of surface and cross-section of grown films, and X-ray diffraction (XRD) for their phase structure; Raman scattering spectum (RSS) and photoluminescence (PL) were used for evaluating their optical characteristics. The results show that, there is textured structure on the surface of grown GaAs polycrystalline films, which is greatly promised to be suitable for the candidate of solar cell with low cost and high efficiency. It is concluded that the source and substrate at temperature of 900 ~ 930 $\^{C}$ and 500 $\^{C}$ respectively would be beneficial for such films.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.353-354
• /
• 2010

The relation between polymer and cement in a polymer-modified cement waterproofing membrane was investigated by using an electron probe micro-analyzer and numerical simulation.

• Proceedings of the KWS Conference
• /
• 2007.11a
• /
• pp.322-324
• /
• 2007

Nd:YAG laser welding of AZ31B-H24 magnesium alloy was carried out using AZ61 filler wire(Mg-6wt%Al-1wt%Zn). Microstructure and mechanical properties of welded joint were examined by optical microscopy, scanning electronic microscopy(SEM), energy dispersive spectroscopy(EDS), electron probe micro analyzer(EPMA) and victors hardness, tensile test at the room and elevated temperature. Test results indicate that the specimens welded with AZ61 filler wire have better tensile strength, elongation and victors hardness at room temperature than those of welded without filler wire. However tensile strength are similar but elongation are quite different at elevated temperature.

• Journal of Radiation Protection and Research
• /
• v.34 no.2
• /
• pp.65-68
• /
• 2009

Metal-semiconductor contact is very important for the operating property of semiconductor detector. $Cd_{0.96}$ $Zn_{0.04}$ Te semiconductor crystal was grown with Bridgman method, and the crystal was cut and polished. EPMA (Electron Probe Micro Analyzer) and ICP-MS (Inductively Coupled Plasma Mass Spectrometry) analysis were done to obtain the chemical composition and impurity of the crystal. Metal contact was deposited with thermal evaporator on both sides of the crystal. Detectors with Au/CZT/Au and In/CZT/Au structure were made, and I-V curve and the energy spectrum were measured with the detectors. It could be seen that the detector with the In/CZT/Au structure has superior property than the detector with Au/CZT/Au structure when the crystal resistivity was low. However, the metal contact structure effect becomes low when the crystal resistivity was high.

• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.110-110
• /
• 2009

본 연구에서는 전산유체역학적 방법을 이용하여 레이저-GMA 하이브리드 용접에서 용융풀 거동에 대한 3차원 과도해석을 수행하였다. 철강재의 주요 합금원소 중 하나인 크롬의 용융풀에서의 거동을 구현하기 위해 크롬에 대해 추가적인 보전 방정식을 도입하였다. 이를 이용하여 합금원소 분포에 대한 용접 변수별 영향을 해석적으로 분석하였으며 이를 EPMA(Electron Probe Micro Analyzer)를 통해 분석한 시험결과와도 비교하였다. 결과적으로 용접변수 중 선행 조건이 합금원소 분포에 구별할만한 영향을 미침을 알 수 있었고 이는 용융풀의 거동을 지배하는 주요 유동 패턴의 상이함에 기인한 것으로 보여진다.

• Korean Journal of Materials Research
• /
• v.11 no.4
• /
• pp.290-293
• /
• 2001

The SrBi$_2$Nb$_2$O$_{9}$ (SBN) thin films were deposited on p-type(100) Si substrates by rf magnetron sputtering to confirm the Possibility of Pt/SBN/Si structure for the application of nondestructive read out ferroelectric random access memory (NDRO- FRAM). The SBN thin films were deposited by co-sputtering method with Sr$_2$Nb$_2$O$_{7}$ (SNO) and Bi$_2$O$_3$ ceramic targets. The SBN thin films deposited at room temperature were annealed at $700^{\circ}C$ for 1hr in $O_2$ ambient. The structural and electrical properties of SBN with different power ratios of targets were measured by x-ray diffraction(XRD), scanning electron microscopy(SEM), capacitance-voltage(C-V), and current-voltage(I-V). The C-V curves of the SBN films showed hysteresis curves of a clockwise rotation showing ferroelectricity. When the Power ratio of the SNO/Bi$_2$O$_3$ targets was 120 W/100 W, the SBN thin films had excellent electrical properties. The memory window of SBN thin film was 1.8 V-6.3 V at applied voltage of 3 V-9 V and the leakage current density was 1.5 $\times$ 10$^{-7}$ A/$\textrm{cm}^2$ at applied voltage of 5 V The composition of SBN thin films was analysed by electron probe X-ray micro analyzer(EPMA) and the atomic ratio of Sr:Bi:Nb with pawer ratio of 120 W/100 W was 1:3:2.

• 보존과학연구
• /
• s.15
• /
• pp.59-103
• /
• 1994

Painting is well regarded as a stratified structure by the conservators and restorers. Hence, the scientific methods have been developed for the study of the interal layer of paintings. Examples of such methods are X-ray, infra-red, and ultra-violet photography. A more direct method is to look at the painting in cross section under the microscope and to analyze pigments using an electron probe X-ray micro analyzer(EPMA).In this research, I study and analyze twenty two Korean paintings of self-portraits including the first oil painting of Hui Dong Koh's self-portrait stored in the museum of Tokyo National University of Fine Arts and Music, employing these scientific techniques. The small fragments taken from the ground layers of the early oil paintings(1915∼1942)are analyzed using the EPMA. According to their main materials, the ground layers can be classified into five types ; 1. Lead white layer and double layer of calcium carbonate and lead white, 2. Zinc white with some mixiture of lead white, 3.Titanium white with some barium white, 4. Barium white, 5.Double layer of titanium white and zinc white.

• Corrosion Science and Technology
• /
• v.17 no.1
• /
• pp.1-5
• /
• 2018

As structural materials, magnesium (Mg) alloys have been widely used in the fields of aviation, automobiles, optical instruments, and electronic products. There are few studies on the effect of coating conditions on the compositional variation during the formation process of the conversion coatings. Rare-earth based conversion coating on AZ91 magnesium alloy was prepared in ceric sulfate and hydrogen peroxide contained solution. The element composition and valence as well as their distribution in the coating were analyzed with energy dispersive X-ray spectroscopy (EDS), Electron probe micro-analyzer (EPMA), X-ray photoelectron spectroscopy (XPS). The effect of treating process on the element composition were also studied. It was found that the conversion coating surface consists of Mg, Al, O, Ce, and the weight content of Ce in the coating was affected by the treating solution concentration and immersion time; the Ce element was distributed in the coating non-uniformly and existed in the form of $Ce^{+3}$ and $Ce^{+4}$, while the O element existed in the form of $OH^-$, $O^{2-}$, $H_2O$. Based on microscopic analysis results, the electrochemical deposition mechanism on the micro-anode and micro-cathode in the process of the coating growth was suggested.

• Korean Journal of Materials Research
• /
• v.20 no.1
• /
• pp.19-24
• /
• 2010

The current study examined Ag migration from the Ag paste bump in the SABiT technology-applied PCB. A series of experiments were performed to measure the existence/non-existence of Ag in the insulating prepreg region. The average grain size of Ag paste was 30 nm according to X-ray diffraction (XRD) measurement. Conventional XRD showed limitations in finding a small amount of Ag in the prepreg region. The surface morphology and cross section view in the Cu line-Ag paste bump-Cu line structure were observed using a field emission scanning electron microscope (FE-SEM). The amount of Ag as a function of distance from the edge of Ag paste bump was obtained by FE-SEM with energy dispersive spectroscopy (EDS). We used an electron probe micro analyzer (EPMA) to improve the detecting resolution of Ag content and achieved the Ag distribution function as a function of the distance from the edge of the Ag paste bump. The same method with EPMA was applied for Cu filled via instead of Ag paste bump. We compared the distribution function of Ag and Cu, obtained from EPMA, and concluded that there was no considerable Ag migration effect for the SABiT technology-applied printed circuit board (PCB).

• Journal of the Korean Ceramic Society
• /
• v.46 no.2
• /
• pp.131-136
• /
• 2009

Radio frequency (RF) plasma treatment is studied for the size reduction and the spheroidization of coarse particles to change them into nano-sized powders of spherical shape in MLCC fields. The uni-nanoadditives manufactured by RF plasma processing for high dispersion have been investigated for the effect on core-shell structure in dielectrics of MLCC. Microstructures have been characterized using scanning electron microscope (SEM), transmission electron microscope (TEM) and Electron Probe Micro Analyzer (EPMA). We compared the distribution of core-shell grains between specimens manufactured using uni-nanoadditive and using mixed additive. In addition, the uniformity of rare earth elements in the core-shell structured grains was analyzed. It was shown, from TEM observations, that the sintered specimen manufactured using uni-nanoadditives had more dense small grains with well-developed core-shell structure than the specimen using mixed additives, which had a homogeneous microstructure without abnormal grain growth and shows broad temperature coefficient of capacitance (TCC) curves in all temperature ranges because of well dispersed additives.