• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.2
• /
• pp.142-145
• /
• 2018

In this paper, we present a design technique for the suppression of common-mode(CM) noise in switched-mode power supply boards using the segmentation method. By applying the segmentation method, the example structure is decomposed into two segments with decoupling capacitors and a recombination matrix is extracted for the segments. The effects of the decoupling capacitor on CM noise suppression are examined. The simulation time is significantly reduced on using the segmentation method.

• Journal of Advanced Navigation Technology
• /
• v.22 no.5
• /
• pp.351-358
• /
• 2018

In this study, we propose a method of suppressing the leakage noise signal of motor assembly through the test. The motor assembly is mounted on outside of the aircraft to rotate an antenna and must satisfy RE102 requirement on MIL-STD-461F in terms of electromagnetic interference. It is confirmed by RE102 test result hat the leakage noise signal of the equipment occurs due to external influx through the power and control cable and rotation of the motor. And it is ascertained that the part where internal/external physical shielding is difficult to rotate is the leakage path. To reduce the leakage noise signal, the electrical ground reinforcement and the electric shielding structure considering the operation of the equipment is applied and it is verified that the requirement is satisfied. Finally, we verified that required specification are met by applying circular corrugated choke with interlocking shapes and conductive grease to the noise leakage path.

• Journal of the Institute of Convergence Signal Processing
• /
• v.25 no.2
• /
• pp.52-57
• /
• 2024

To measure the vortex structures within the turbulent boundary layer, a hot-wire sensor was mounted on a stepper motor controller and moved to the designated measurement points. Near the surface within the flow field, the velocity is relatively slow, making the measurements highly sensitive to electromagnetic interference (EMI) during signal processing. This EMI primarily originates from the power supplies of computers and other electronic equipment. In our experimental setup, EMI was introduced into BNC cables connected to the hot-wire sensor from the powered stepper motor. When power was supplied to the motor controller to move the hot-wire sensor, EMI appeared on the oscilloscope screen. Consequently, unexpected noise was present in the data measured by the hot-wire sensor. To mitigate this and enhance the signal-to-noise ratio (SNR) during measurements, the connecting cables were shielded, and an old computer without EMI shielding was replaced.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.7
• /
• pp.757-765
• /
• 2007

OFDM system is an excellent high speed transmission method but it is seriously sensitive to the phase noise and IQ imbalance. Therefore, in this paper, we analyze the communication performance of the OFDM communication system with IQ imbalance and phase noise. Phase noise's variance can be calculated by integral calculus of phase noise power spectrum. From simulation results, it can be shown that the BER performances show different change according to the phase noise variance and IQ imbalance amount. When amplitude imbalance is ${\varepsilon}$=0.2; 0.3; 0.4 and phase imbalance is ${\phi}=10^0$, and distribution of phase noise is ${\sigma}^2=0.012$, BER is degraded by 2.88 dB, 3.61 dB, 4.09 dB in $10^{-5}$ in the respect of the SNR penalty.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.4
• /
• pp.470-476
• /
• 2008

In this paper, we describe the cause of TDMA noise and distinction method of TDMA noise source in a GSM mobile phone. The causes of TDMA noise are composed of RF(Radio Frequency) energy coupling and low frequency energy coupling by burst ripple. We propose the distinction method of TDMA noise source from output(TDMA noise measurement) and frequency response of a system(audio path). Especially we propose a method of insertion loss($S_{21}$) analysis and the improvement method for RF energy coupling. Capacitor(40 pF) is a solution to reduce RF energy coupling and therefore TDMA noise was reduced by 10 dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.2
• /
• pp.152-160
• /
• 2008

In this paper, we analyze the performance of a direct-conversion UHF RFID reader with the range correlation effects of the phase noise. Since a UHF RFIB system uses the same oscillator to generate the transmitted carrier and the local oscillation, the periodic interference and phase noise reduction effects occur due to time delay between two signals. Through exact theory and simulation, we verify how to cancel the periodic interference phenomena using I/Q diversity combining technique. And, we analyze phase noise reduction effects due to range correlation as a function of the tag-reader distance and the offset frequency Using these results, we simulate the symbol-error-rate performance with respect to phase noise with and without range correation effects. We show that the phase noise of the local oscillator has little effect on the symbol-error-rate performance because of phase noise reduction by range correlation.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.212-217
• /
• 2008

Acoustic noises generated during motor operation in mechanical system are from electromagnetic, mechanical, aerodynamic, and electrical sources. For identification of mechanical noise origins, misalignment, unbalance, fan shape, resonance, and vibration modes have been extensively considered to describe noise behavior. An experiment-based approach as well as a mathematical approach needs to be adopted for a realistic study into noise and vibration of the motor, because motor noise characteristics differ from type to type due to various noise sources. In this paper, a brushless DC motor for air-conditioner fan is analyzed by finite element method to identify noise source, and the analysis results are verified by experiments, and sensitivity analysis is performed by design of experiments.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2000.02a
• /
• pp.26-28
• /
• 2000

Generally high frequency electromagnetic waves can not penetrate into waveguide, and it is called skin effect. Since the shape of superconducting CICC (Cabel In Conduit Conductor) is similar to that of waveguide, the characteristics of waveguide can be applied to CICC. In this paper, we analyzed penetrated magnetic field in CICC according to external noise. From it, noise frequency bandwidth affecting voltage tap sensor in CICC was found.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.8
• /
• pp.138-144
• /
• 2004

Satellite generates a complex electromagnetic noise by conducted and radiated coupling effect of the various electrical instruments. This noise may cause serious problems on the satellite system. To minimize the electromagnetic coupling effects and maintain the system safety margin, system noise reduction technique should be applied from the beginning of the system design. The KOMPSAT-2 system is evaluated by measuring the conducted noise on system electrical power leads and verifying a 6dB system safety margin under the complex noise environment with current injection. This paper describes the KOMPSAT-2 system evaluation result performed on ETB(Electrical Test Bed) and the analysed noise element, the analysed result will be reflected on FM(Flight Model) EMC test.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.36 no.12
• /
• pp.1207-1215
• /
• 2008

Satellite generates a complex electromagnetic noise by conducted and radiated coupling effect of the various electrical instruments. This noise may cause serious problems on the satellite system. To minimize the electromagnetic coupling effects and maintain the system safety margin, system noise reduction technique should be applied from the beginning of the system design. The COMS system is evaluated by measuring the conducted noise on system electrical power leads at PSR(Power Supply Regulator) and verifying a 6 dB system safety margin under the complex noise environment with current injection. The radiated noise due to the complex transmit antenna configuration is evaluated by integrating all unit-level RE measurement results, and the RF compatibility between spacecraft and launch vehicle is analyzed with the above estimations. This paper describes the COMS EMC compatibility analysis with respect to each unit level EMC test results, and RF compatibility analysis between spacecraft and launch vehicle. The analyzed results will be reflected on FM(Flight Model) EMC test.