• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.8
• /
• pp.748-753
• /
• 2002

In this paper, a new topology of a active capacitor is proposed in order to apply the resonator in the design of RF active bandpass filters. Through the noise analysis of the active capacitor, the optimized low noise design process is also presented, Due to the low noise performance of the proposed active bandpass filter, it can be used in the RF front-end of the receivers. In designed 2-stage active bandpass filter at 1.9 GHz shows insertion loss of 0 dB, noise figure of 2.6 dB, and OIP3 of 8 dBm.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.3
• /
• pp.240-247
• /
• 2009

In this paper, we proposed the method of the interference evaluation between the microwave oven noise and the wireless LAN(Local Area Network) by using the GTEM cell. We used microwave oven noise in time to assess the interference unintentional noise effects on wireless LAN and realized by combining an AM(Amplitude Modulation) modulator and a FM(frequency Modulation) modulator. Also the GTEM cell can be used to guarantee the reliability by the evaluations of the frequency and time responses. As measurement results for the APD(Amplitude Probability Distribution) of the interfering noise we analyzed the effect of microwave oven noise to the throughput of wireless LAN.

• Journal of Electrical Engineering and Technology
• /
• v.1 no.1
• /
• pp.85-91
• /
• 2006

Recently, the reduction of electromagnetic vibration and noise of a capacitor motor (CRM) has become a very important subject from the standpoint of environmental improvement. Therefore, the authors have studied the characteristics of the dominant electromagnetic vibration of the CRM under load condition. In this paper, the effects of slot combination and skewed slot on the dominant electromagnetic vibration of a CRM under load condition are discussed both theoretically and experimentally. As a result, the characteristics of the dominant electromagnetic vibration for the slot combination and the reduction effect of the skewed slot on the electromagnetic vibration are clarified for a 4-pole CRM.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.05a
• /
• pp.511-512
• /
• 2010

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.12
• /
• pp.1072-1082
• /
• 2015

In this paper, we propose two noise parameter measurement methods using spectrum analyzer. First method, we measure a noise correlation matrix using the 6-port network, and we calculate noise parameters using measured a noise correlation matrix. Second method, we directly measure noise figures of the DUT for source impedance changes, and then noise parameters are extracted from the measured noise figures. In order to measure a noise figure, we present a method of measuring a noise figure of the DUT that have arbitrary source impedances using spectrum analyzer and a method of eliminating a noise effect of a impedance tuner. Finally, the noise parameters of a passive and active DUT using proposed two methods are compared. The comparison shows that the two results obtained from for the two methods give almost identical noise parameters. The noise parameters measured by 6-port network accurately predict measured noise figures of the DUT for source impedance changes, and noise parameters measured by 6-port network is verified from the comparison.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.10a
• /
• pp.459-460
• /
• 2010

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.05a
• /
• pp.158-159
• /
• 2010

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.26 no.2
• /
• pp.119-126
• /
• 2015

The information about noise parameters is essential in the design of low noise amplifier. In the past, the noise parameters were measured using an impedance tuner and noise figure analyzer. Recently, the authors proposed the method of measuring the noise parameters using the 8-port network without the aid of the mechanically driven impedance tuner. However, the 8-port method still requires the noise source and causes the complexity in the measurements. In this paper, a novel measurement method of the noise parameters without the noise source using 6-port network is proposed. Based on the proposed 6-port method, the noise parameters of 10 dB attenuator whose noise parameters can be theoretically determined were measured and the measured noise parameters are compared with those measured using the previous 8-port network method. As a result, the accuracy of the measured noise parameters using 6-port network is found to be comparable to the previous 8-port network method.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.6
• /
• pp.509-515
• /
• 2009

In this paper, we analyzed and evaluated noise suppression characteristic of EM wave absorber. We fabricated several absorber samples in different ratios of Sendust and Amorphous with CPE(Chlorinated Ploy-ethylene) as binder and calculated material constants by measured S-parameter. Then, we confirmed that the noise suppression characteristic of EM wave absorbers using microstrip line. A microstrip line with EM wave absorber placed on its top was used to evaluate the conduction noise suppression. As a result, noise suppression effect show different charateristic by changing relative permeability. Therefore, EM wave absorber using Sendust show excellent characteristic. In particular the maximum power absorption over 90 % in 1.7 GHz to over 6 GHz has obtained when composition of Sendust:CPE=80:20wt.%.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.8
• /
• pp.777-786
• /
• 2003

The phase noise characteristics of the phase-locked loop frequency synthesizer were predicted based on the analysis for phase noise contribution of noise sources. The proposed phase noise model in this paper more accurately predicts the phase noise spectrum of frequency synthesizer. To accurately model the phase noise contribution of noise sources in frequency synthesizer, the phase noise sources were analyzed via modeling of the frequency divider and phase noise components using Leeson model for reference signal source and VCO. The phase noise transfer functions to VCO from noise sources were analyzed by superposition theory and linear operation of phase-locked loop. To evaluate the phase noise prediction model, the frequency synthesizers were fabricated and were evaluated by measured data and prediction data.