• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2001.11a
• /
• pp.119-122
• /
• 2001

In this paper, an elliptic disk-loaded antenna having frequency shift characteristics with the same height of the simple monopole is studied. The proposed antenna is composed of an ellitptic disk with arbitrary ellipticity ratio. The eigenmode representations in each region of given structure are useful for the analysis of the canonical monopoly, circular disk-loaded monopole and circular dielectric-loaded top-hat monopole antennas using the artificical ground plane. The comparison between the elliptic and circular disk-leaded antenna is carried out. The effect of the shape of the loaded disk and the ellipticity ratio of the loaded disk on the input impedances, the return loss and frequency shift is also studied. We have computed the given structures using the CST MW Studio version 3.0. The typical blade antenna can be obtained by modifying and extending the proposed structure with the λ/4 balun removing the stray capacitances existing between the loaded disk and the ground plane.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2001.11a
• /
• pp.222-226
• /
• 2001

In this paper, 2.4GHz RF Module using Even Harmonic Mixer(EHM) was designed and fabricated for Direct conversion(DC) system. By minimizing performance degradation of DC system with DC offset and LO radiation, the capability of minimization and one chip solution in wireless system was proposed. The designed EHM using anti-parallel diode pair represented 9dB conversion loss and about -60dBm 2LO leakage radiation in RF port, and output reflection and reverse transmission characteristic of low noise amplifier was improved. So superior DC offset suppression characteristic is expected. RF Module which consists of EHM, LNA, RF amplifier, Frequency synthesizer and Duplexer was designed and fabricated.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2001.11a
• /
• pp.243-246
• /
• 2001

A cavity delay filter module for IMT-2000 LPA has been developed with 0.9dB insertion loss, 0.1dB/0.6$^{\circ}$ gain/phase flatness. Broadband signal cancellation of the module has been simulated using the measured S parameter, and gain, phase and group delay have been matched to satisfy the signal cancellation of the module. In the experiment, the value of designed parameters are used and 40dB signal cancellation has been obtained over 100MHz bandwidth. Also the sampling cancellation has been shown to be the similar performance of the feedforward output cancellation.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.442-445
• /
• 2003

The use of a single UWB antenna which covers a wide range of frequencies is very desirable for future wireless communications system. In this paper, we propose a novel wide band printed elliptic monopole antenna for UWB(Ultra wide Band). Wideband planar monopole disc antenna have been recently studied. The proposed antenna can cover UWB frequencies from 3.5GHz to 12GHz. it is determined from 10dB return loss. The antenna consists of the printed elliptical monopole disc with microstrip-line feed. Elliptic disc of antenna and ground height operate important to matching. The results of measurement are almost similar to those of simulation.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.173-177
• /
• 2003

In this paper, a new modeling methodology of thin film bulk acoustic resonate. (TFBAR) is presented. The new model is started from the Mason model that is a good model to explain the physical characteristics of TFBAR. After simplifying the modified Mason model added dielectric loss term to conventional Mason model, the improved Modified Butterworth-Van Dyke (MBVD) model similar to conventional MBVD model is complete. The proposed model has three optimization variables those are half of the MBVD model. As a result, the curve fittings for the measured data are faster and smarter than any other model.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.322-325
• /
• 2003

A 7/21GHz frequency tripler, using a commercially available packaged pHEMT, was designed and fabricated on 15mil RO3003 substrate. Frequency conversion is realized using the third harmonic current of an class B amplifier with rejection feedback at fundamental with optimum load conductance at the third harmonic. The fabricated frequency tripler has achieved a conversion loss of 0.7dB for an input power of 0dBm at 21GHz. The experimental results show good agreement with the harmonic balance simulation.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.413-417
• /
• 2003

In this paper, a series-fed microstrip array antenna utilized a sub-array with a waveguide slot feeding is presented. This sub-array can reduce the feed loss compared with a full microstrip feed network. The sub-array has been designed both for a broad reflection bandwidth and a flat gain bandwidth from 40.5 GHz to 43.5 GHz. The $24{\times}24$ array antenna has been implemented with the maximum gain of 32.4 dBi.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.524-527
• /
• 2003

In this paper, a new design for a Coplanar Waveguide (CPW) fed wide-band slot antenna is presented. To enhance the impedance bandwidth of the slot antenna, we proposed the tapering slot structure. A various resonance modes are generated in the tapering slot. The impedance bandwidth of the proposed antenna is about 12:1 ($2.0GHz{\sim}24.3GHz$) with $VSWR{\le}2$. Simulation results for return loss and radiation pattern are presented.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.630-637
• /
• 2003

In this paper, a DBM(double balanced mixer) of 2 GHz is implemented on FR4(h=1.6mm, ${\epsilon}_r=4.6$) substrate. The structure of double balanced mixer requires, in general, two talons and a quad diode. For balun, a novel planar balun using microstrip to CPS(Coplanar Strip) is suggested and designed. The suggested balun shows the phase imbalance of $180^{\circ}{\pm}1.5^{\circ}$ and the amplitude imbalance of ${\pm}0.2 dB$ for 1.5 to 2.5 GHz. Using the balun, DBM is successfully implemented, and the measured conversion loss of up/down converter show about 6 dB over the bandwidth. The balun may be applicable for MMIC(Monolithic Microwave Integrated Circuit) DBM with the process supporting backside via though more study.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.638-648
• /
• 2003

An active capacitance circuit is analyzed in depth and its application to active RF BPF with low noise figure is discussed. The characteristics of the active capacitance circuit made of FET[1] exhibits negative resistance and conventional capacitance, which is easily controlled. However, it is difficult to make the negative resistance adequate in the designated frequency range due to the lack of detailed analysis, which could make an active circuit unstable as the frequency is going higher or lower. In this paper, we analyzed the negative resistance characteristics of active capacitance circuits and also presented the method that the flatness of passband can be controlled. Finally we have designed a 4-stage active BPE, which results in bandwidth of 100 MHz, 0,04 dB insertion loss, 0.2 dB ripple, and noise figure of 2.4 dB at 1.75 GHz band.