• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1997.04a
• /
• pp.96-101
• /
• 1997

In recent years, grinding techniques for precision machining of brittle materials used in electric, optical and magnetic parts have been improved by using superabrasive wheel and precision grinding machine. The present dressing system cannot have controll of optimum dressing of the superabrasive wheel. In this study, a new system and the grinding mechanism of optimum in-process electrolytic dressing were proposed. This system can carry out optimum in-process dressing of superabrasive wheel, and give very effective control according to unstable current and gap increase. Therefore, the optimum in-process electrolytic dressing is a good method to obtain the efficiency and mirror-like grinding of brittle materials.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.634_635
• /
• 2009

Large aluminium electrolytic capacitors are widely used in inverter systems for smoothing dc-link voltage. If capacitors in dc-link are deteriorated by ageing, dc-link voltage is fluctuated by lessened capacitance and their bodies are heated by raised ESR(equivalent serial resistance) and finally system faults can be occurred. In this paper, on-load ageing test method of electrolytic capacitor in inverter system is proposed and test results are shown.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.03a
• /
• pp.59-64
• /
• 1998

We need to achieve th mass product through methods of higher efficient, higher precise manufacturing process than those of existing precision abrasive machining. Thus, this study is to develop mirror-like surface machining technique of outer diameter of the piston pin by the compound magneto-electrolytic abrasive polishing system. The procedure of machining is followed as first, fulfill the pre-processing by cylindrical grinder, second, complete mirror-like surface by the method of magneto-electrolytic abrasive polishing used CBN non-woven abrasive pads. In this study, it was found that the best suitable conditions of mirror-like surface polishing were that the electrode density was 0.1A/$\textrm{cm}^2$, the applied pressure 1.5kgf/$\textrm{cm}^2$, the feed rate 0.5mm/rev, and the rotoation velocity of workpiece 80rpm, and that the surface roughness was reduced in this conditions.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.5
• /
• pp.29-37
• /
• 1998

In recent years, grinding techniques for precision machining of stainless steel used in shaft, screw parts and clear value have been improved by using the superabrasive wheel and precision grinding machine. The completion of optimum dressing of superabrasive wheel makes possible the effective precision grinding of stainless steel. However, the present dressing system cannot have control of optimum dressing of the superabrasive wheel. In this study, a new system and the grinding mechanism of optimum in-process dressing of superabrasive wheel. Therefore, the optimum in-process electrolytic dressing is a good method to obtain the efficiency and mirror-like grinding of stainless steel (STS304)

• The Transactions of the Korean Institute of Power Electronics
• /
• v.23 no.1
• /
• pp.59-65
• /
• 2018

A new single-stage flyback power converter with PFC for electrolytic capacitor-less LED driver is proposed in this study. This method minimizes the peak-to-average ratio of the LED driving pulsating current by adding the LED driving current near the LED current valley area, as well as the third harmonic component injection into the input current. The reduced peak current value of the LED drive current minimizes the thermal stress of the LED itself, thereby increasing the reliability of the LED, as well as achieving a long lifetime. Simulation and experimental results show the usefulness of the proposed topology.

• Proceedings of the KIPE Conference
• /
• 2012.07a
• /
• pp.55-56
• /
• 2012

In general, a power decoupling method using electrolytic capacitor is used to solve a problem that appears 120[Hz] ripple of grid at the PV module output. But electrolytic capacitor has a effect on the short lifetime and low reliability of PV system. Therefore, studies which replace the large electrolytic capacitor with small film capacitor have been researched in resent years. This paper proposes flyback inverter which can be replaced with film capacitor by connecting the circuit implementing zero voltage switching in PV side. The proposed system is validated by PSIM simulation.

• Textile Coloration and Finishing
• /
• v.15 no.3
• /
• pp.140-145
• /
• 2003

The purpose of this study is searching the Elm-Bark dyes' dyeability and antibacterial activities according to the dyeing time, pH, a mordant and the method of mordancy. We used two kinds of Elm-Bark dyes which's extracted by the Electrolytic reduction water and Distilled water. Silk fabric and Cotton/nylon union fabric was used for this study. The results are as follow. K/S value is increased according to the dyeing time and the suitable pH level is pH 3. Dyeability is good with Iron(II) sulfate$(FeSO_4\cdot{7H}_2O)$ on the pre-mordancy and Potassium dichromate$(K_2Cr_2O_7)$ on the post-mordancy. The Elm-Bark dyes by the Electrolytic reduction water has good colorfastness more than by the Distilled water. Antibacterial activities is excellent and the ratio is over than 99.5%.

• Journal of Surface Science and Engineering
• /
• v.51 no.6
• /
• pp.400-404
• /
• 2018

A metal 3D printer has been developed on its own to electrodeposit the localized area. Nozzles were used to selectively laminate the electrolytic plating method. To analyze the factors affecting the deposition, the stack height, thickness and surface roughness were experimentally analyzed according to the current density and the temperature of the electrolyte. Electrolytic temperature and current are electrodeposited when the deposition conditions are dominant over the etching conditions, but the thickness is kept constant. On the contrary, when the etching conditions are dominant, the electrodeposited shape is rather the etched. As a result, the uniformity of surface quality and electrodeposition rate could be improved by conducting experiments under constant conditions of electrolyte temperature and current density.

• Textile Coloration and Finishing
• /
• v.10 no.2
• /
• pp.18-28
• /
• 1998

in order to overcome disadvantage of the conventional two bath dyeing method of polyester/cotton blends, it had prompted significant effort to the development of the one bath dyeing method which can accomplish sayings in time, energy and water usage. Also, when dyeing polyester/cotton blends by the one bath dyeing method, the high salt concentrations needed for the reactive dye can cause particles of disperse dye, used for the polyester component, to aggregate. A supplementary problem that can occasionally be happened is the change of hue that occurs on dyed polyester in an alkaline dyebath. To improve dyeing property of polyester/cotton blends, cotton component was pretreated with epichlolohydrine-trimethylamine hydrochloride in aqueous solution of sodium hydroxide to produce a cationized cotton that can be dyed under neutral conditions with reactive dye in a non-electrolytic or il little electrolytic dyebath. The one bath dyeing method of polyester/cationized cotton blends with disperse dye/reactive dye mixture resulted in a satisfactory dyeing property and color yield in comparison with ordinary two bath dyeing method.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2004.05a
• /
• pp.834-837
• /
• 2004

In this study, the electric accelerated reinforcing bar corrosion test was carried out to estimate the coefficient of electrolytic corrosion based on the concept of Faraday's law according to rebar corrosion rate and concrete compressive strength which had an effect on the actual corrosion mass loss. The results of this paper allow the prediction of corrosion amount in the electric accelerated reinforcing bar corrosion test method.