• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.12 no.2
• /
• pp.17-22
• /
• 2003

Electropolishing is the electrolytic removal of metal in a highly ionic solution by means of an electrical potential and current. It is normally used to remove a very thin layer of material on the surface of a metal part or component. Electropolishing is able to enhance the material properties of a workpiece and to change its physical dimensions. Also, It is suitable for the polishing of both complex shapes and hardened materials, which are difficult to machine mechanically. therefore, the aim of the present study is to investigate the characteristic of Electropolishing A12024 in terms of current density, polishing time and electrode gap, etc.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.2
• /
• pp.89-96
• /
• 2000

This paper describes the characteristic of die finishing to obtain smooth surface using electro-chemical grinding after cutting process. Electro-chemical grinding is possible under lower load and tool wear comparing with those in the mechanical grinding. Conventionally, if the metal bonding material of the grinding wheel is directly t contacted with workpiece, the current is circulated without electrolytic phenomena. Sometimes, electrical discharge is occurred between tool and workpiece. To cope with this problem, the metal-resin bonded pellet was used in this study. This pellet is composed of optimal volume of metal and resin powders and its characteristics are changable with the each volume of powders. Finally, high efficient die finishing is realized using metal resin bonded pellet in electro-chemical grinding.

• Journal of environmental and Sanitary engineering
• /
• v.11 no.2
• /
• pp.53-58
• /
• 1996

This study was performed to measure and evaluate the characteristics of removal efficiency and kinetics in the electrolytic decolorizing process of dye wastewater containing acid dye Red 114 by using Fe anode. The synthetic wastewater samples of 500, 1000, $2000mg/{\ell}$ concentration were tested and as an attempt to assess the feasibility of the present system for the industrial application, a sample of wastewater collected by J textile factory in Eujungbu city was also treated. It was found that the optimum conditions were pH 7, 8Volt and removal efficiency in synthetic wastewater containing $2000mg/{\ell}$ of dye and 0.2% of electrolyte (NaCl) was 99.68% after 20minutes of reaction time. In this condition, overall rate constant was $4.77{\times}10^{-5}mmol/cm^{3}hr$. The Decolorizing efficiency and COD removal efficiency of J textile factory wastewater were 99% and 86% respectively at pH 7, 8Volt for 40minutes of reaction time.

• Journal of the Korean Applied Science and Technology
• /
• v.27 no.1
• /
• pp.61-69
• /
• 2010

This study is focused on the modeling of two phase fluid flow system in the electrode of hydrogen gas generator. The characteristics of hydrogen gas generation was studied in view of efficiency of hydrogen gas generation rate and a tendency of gas flow through the riv of electrode. Since the flow rate of generated gas is the most crucial in determining the efficiency of hydrogen gas generator, we adopted the commercial analytical program of COMSOL $Multiphysics^{TM}$ to calculate the theoretical flow rate of hydrogen gas from the outlet of gas generator.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.9
• /
• pp.1897-1904
• /
• 2002

Monotonic torsional and pure torsional low cycle fatigue(LCF) test with artificial degradation were performed on duplex stainless steel(CF8M). CF8M is used in pipes and valves in nuclear reactor coolant system. It was aged at 430$^{\circ}C$ for 3600hrs. Through the monotonic and LCF test, it is found that mechanical properties(i.e., yield strength, strain hardening exponent, strength coefficient etc.) increase and fatigue life(N$\sub$f/) decreases with degradation of material. The relationship between shear strain amplitude(${\gamma}$$\sub$a/)and N$\sub$f/ was proposed.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.11 no.5
• /
• pp.58-64
• /
• 2002

Mirror surface finish of Si-wafers has been achieved by rotary in-feed machining with cup-type wheels in ELID grinding. But the diameter of the workpiece is limited with the diameter of the grinding wheel in the in-feed machining method. In this study, some finding experiments by the rotary surface grinding machine with straight type wheels were conducted, by which the possible grinding area of the workpiece is independent of the diameter of the wheels. For the purpose of investigating the grinding characteristics of large scale diametrical silicon wafer, grinding conditions such as rotation speed of grinding wheels and revolution of workpieces are varied, and grinding machine used in this experiment is rotary type surface grinding m/c equipment with an ELID unit. The surface ground using the SD8000 wheels showed that mirror like surface roughness can be attained near 2~6 nm in Ra.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.946-949
• /
• 2001

Mirror surface finish of Si-wafers has been achieved by rotary in-feed machining with cup-type wheels in ELID grinding. But the diameter of the workpiece is limited with the diameter of the grinding wheel in the in-feed machining method. In this study, some grinding experiments by the rotary surface grinding machine with straight type wheels were conducted, by which the possible grinding area of the workpiece is independent of the diameter of the wheels. For the purpose of investigating the grinding characteristics of large scale diametral silicon wafer, grinding conditions such as rotation speed of grinding wheels and revolution of workpiece are varied, and grinding machine used in this experiment is rotary type surface grinding m/c equipped with an ELID unit. The surface ground using the SD8000 wheels showed that mirror like surface roughness can be attained near 2~6nm in Ra.

• Fashion & Textile Research Journal
• /
• v.7 no.3
• /
• pp.339-345
• /
• 2005

It is difficult to dye nylon/viscose rayon mixture fabrics by one-bath one-step dyeing method, because acid dyes and reactive dyes require acidic dyebath for adsorption and alkaline dyebath for fixation respectively. In order to overcome the disadvantage of the conventional two bath two step dyeing method of nylon/viscose rayon mixture fabric, it was pretreated with cationizing agent containing chlorohydrine group in aqueous solution of sodium hydroxide. The pretreated nylon/viscose rayon mixture fabrics produced cationized fabrics that could be dyed with acid dyes and reactive dyes under neutral condition. This study was carried out to investigate dyeing possibilities, surface reflectance spectra and color characteristics of cationized nylon/viscose rayon mixture fabrics with acid dyes and reactive dyes in a non-electrolytic and neutral dyebath by one bath one step dyeing method.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.533-535
• /
• 2002

Electrode formation methods such as a metal-taping, a electrolytic plating, and a metal-paste melt-bonding, are introduced for an external electrode fluorescent lamp. The characteristics of luminance and efficiency for various external electrode types have been investigated.

• Journal of the Korean Applied Science and Technology
• /
• v.27 no.2
• /
• pp.152-156
• /
• 2010

This study is focused on the channel design of bipolar plate in the electrode of hydrogen gas generator. The characteristics of hydrogen gas generation was studied in view of efficiency of hydrogen gas generation rate and a tendency of gas flow through the riv design of electrode. Since the flow rate of generated gas is the most crucial in determining the efficiency of hydrogen gas generator, we adopted the commercial analytical program of COMSOL $Multiphysics^{TM}$ to calculate the theoretical flow rate of hydrogen gas from the outlet of gas generator.