• Korean Journal of Materials Research
• /
• v.9 no.6
• /
• pp.564-568
• /
• 1999

The 8-hydroxyquinoline Zinc(Znq2) were prepared successfully from zinc chloride and zinc acetate as two kinds of starting material. The organic electroluminescent devices(ELDs) were fabricated by the structure of ITO/TPD/Znq2/Al with N-N'-diphenyl-N-N'-bis(3-methylphenyl)-1,1'-biphenyl-4,4'-diamine(TPD) which acts hole trasporting layer and bis(8-oxyquinolino) zinc(II)(Znq2) which acts as emission and electron transporting layer. EL efficiency of Znq2 prepared by heating was investigated. The 570nm of main emission peak which is yellowich green was investigated by photo luminesence(PL) and this results shows that electro luminescence(EL) is from Znq2. The V-J curve shows that carrier injection were investigated from 4V. Maximum luminance and luminance efficiency were 1600cd/$\m^2$, 0.9lm/W. From this results, the Znq2 can be one of the useful organic EL material.

• Proceedings of the Korean Fiber Society Conference
• /
• 2002.04a
• /
• pp.53-56
• /
• 2002

Today, interest in electroluminescent(EL) diodes has been increasing since vacuum-sublimed thin-film dioes exhibited high performance. And since the discovery of electroluminescence from aluminaqinone, which has uniform $\pi$-conjugated segment by Eastmann kodack,$^1$ lots of attentions have been concentrated on organic EL devices. However, they have disadvantage such as low mechanical intensity, thermic crystallization. (omitted)

• Proceedings of the KIEE Conference
• /
• 2000.11c
• /
• pp.428-430
• /
• 2000

In this paper, the Flexible information display was implemented using AC powder electroluminescent device. ZnS:Cu and $BaTiO_3$ was used as a phosphor and dielectric respectively. The preparation of phosphor and dielectric layer was performed with screen printing. The implemented system of the Flexible information display was divided as following; EL display, driving circuit, software for driving. The properties of fabricated devices was measured with EL spectrum and brightness.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.972-975
• /
• 2002

Electroluminescence(EL) devices based on organic thin layers have attracted lot of interests because of their application as display. One of the problems is red material. It offered a short life and poor emission efficiency to boot. In this study, this problem can be solved by using a multi-layer device structure. Organic electroluminescent devices which are composed of organic thin multi-layer films are fabricated. The basic structure is ITO / Emitting layer / LiP / Al EL device in which Hole transport/Electron blocking PVK layer was blending. We demonstrate the enhancement of eletroluminescence (EL) from blends of poly(3-hexylthiophene) in poly(N-vinylcarvazole). The emitting layer is consisted of a host material(PVK) and a guest emitting material(P3HT). It was showed higher EL intensity and their electro-optical properties were investigated.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.9
• /
• pp.762-767
• /
• 2001

We report the white light emission from the multilayer organic electroluminescent(EL) device using exciplex emission. The exciplex at 500nm originated between poly(N-vinylcarvazole)(PVK) and 2,5-bis(5'-tert-butyl-2-benzoxazoly)thiophene(BBOT) and exciplex of 50nm originated from N,N'-diphenyl-N,N'-(3-methyphenyl)-1,1'-biphenyl-4,4'-diamine(TPD) and BBOT were observed. Also, the energy transfer from PVK to BBOT and poly(3-hexylthiophene)(P3HT) in mixed emitting materials was occurred. The electroluminescence(EL) spectra of organic EL device which have a device structure of ITO/CuPc(5nm)/emitting layer(100nm)/BBOT(30nm)/LiF(1.4nm)/Al(200nm) were slightly changed as a function of the applied voltage. The luminance fo 12.3 ${\mu}$W/$\textrm{cm}^2$ was achieved at 20V and EL spectrum measured at 20V corresponds to Commission Internationale de L\`Eclairage(CIE) coordinates of x=0.29 and y=0.353.

• Electrical & Electronic Materials
• /
• v.8 no.6
• /
• pp.752-758
• /
• 1995

Red emitting CaS:Eu,S electroluminescent(EL) device prepared at 550.deg. C by an electron-beam evaporation technique, demonstrated luminance of 175cd/m$\^$2/ and efficiency of 0.311m/W with 3kHz drive. Luminance was increased with the increase of applied voltage and frequency. From the results of the PL spectrum and the EL spectrum, the CaS:Eu, S device showed emission peak near 640nm resulted from the transition of EU$\^$2+/ 4f$\^$6/5d.rarw.4f$\^$7/. The capacitance of the phosphor layer from the Sawyer-Tower circuit was 10.5nF/cm$\^$2/.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.05a
• /
• pp.27-31
• /
• 2001

We fabricated organic electroluminescent(EL) devices with mixed emitting layer of poly(N-vinylcarbazole)(PVK), 2,5-bis(5'-tert-butyl-2-benzoxazoly)thiophene(BBOT), N,N'-diphenyl-N,N'-(3-methyphenyl)-1,1'-biphenyl-4, 4'-diarnine(TPD) and poly(3-hexylthiophene)(P3HT). To improve the external quantum efficiency of EL devices, we added the functional layer to the devices such as LiF insulating layer, carrier confinement layer(BBOT) and hole injection layer(CuPc). In the ITO/emitting layer/Al device, the maximum quantum efficiency at 15V was $1.88{\times}10^{-5}%$. And then, it is increased by a factor of 27 to $5.2{\times}10^{-3}%$ in ITO/CuPc/emitting layer/BBOT/LiF/Al device at 15V.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.04a
• /
• pp.81-82
• /
• 2006

Doping is a well-known method for improving electroluminescent (EL) efficiency of organic light emitting diodes. In our study, doping with 2 materials simultaneously, we could achieve improved EL efficiency. The emission layer was tris-(8-hydroxyquinoline)aluminum, and the 2 dopants were N,N'-dimethyl-quinacridone (DMQA) and 10-(2-Benzothiazolyl)-2, 3, 6, 7-tetrahydro-1,1,7,7,-tetramethyl 1-1H, 5H, 11H-[1] benzopyrano [6,7,8-ij]quinolizin-11-one (C-545T). The EL intensity of co-doped device was nearly flat, it shows that co-doping technique could be a effective way to improve the EL efficiency. EL efficiency of Single-doped device based on DMQA and C-S45T were ~6.47Cd/A and ~7.45Cd/A, respectively. Co-doped device showed higher EL efficiency of ~8.30Cd/A.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2001.10a
• /
• pp.613-616
• /
• 2001

The effect of codopants on the electroluminescent properties for SrS-Ce based thin films was studied. The active layer was deposited by electron beam with sulfur The wavelength of eletroluminecence shifted with codopants and their concentrations. The intensity ratio of blue to green were found In the CeP-doped device, but the highest total intensity of luminance showed about 850cd/$m^2$ in the CeCl$_3$+KCL-doped device, which indicates that codopants are playing an important role of luminance. At any device, the luminance was the strongest at 0.2 mol% concentration among the concentration studied, suggesting the existence of optimum concentration. By post-annealing Luminance of most devices was improved, but the shift of wavelength was not observed.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.332-335
• /
• 2000

We fabricated organic electroluminescent (EL) devices with single layer of poly(3-dodeoylthiophene) (P3DoDT) hlended with different amounts of poly(N-vinylcarbazole) (PVK) as a emitting layer. The molar ratio between P3DoDT and PVK changed with 1:0, 2:1 and 1:1. To improve the external quantum efficiency of EL devices, we applied insulating layer, LiF layer, between polymer emitting layer and Al electrode. All of the devices emit orange-red light and it's can be explained that the energy transfer occurs from PVK to P3DoDT. In the voltage-current and voltage-brightness characteristics of devices applied LiF layer, current and brightness increased with increasing applied voltage. The brightness of the device have a molar ratio 1:1 with LiF layer was about 10 times larger than that of the device without PVK at 6V. Electrical impedance properties of ITO/emitting layer/LiF/Al devices were investigated. In the Cole-Cole plots of impedance data, one semicircle was observed. Therefore, the equivalent circuit for the devices can be designed as a single parallel resistor and capacitor network with series resistor.