• 마이크로전자및패키징학회지
• /
• 제27권2호
• /
• pp.39-44
• /
• 2020

최근 웨어러블 장치에 적용하기 위한 유연성 기판에 대한 연구가 활발히 진행되고 있다. 특히, 유연성 기판 중 의복에 웨어러블 장치를 적용하기 위한 전도성 섬유기판에 대한 연구가 진행되고 있다. 본 연구에서는, 면섬유 기판 표면에 CNT와 Pd복합 용액을 스프레이 법을 이용하여 형성하였고, 무전해 도금법을 이용하여 금속층을 도금하였다. 도금된 섬유기판의 형상을 분석하기 위하여 SEM 장비를 이용하였고, CNT를 증착한 섬유기판의 표면에 Ni 레이어가 형성된 것을 확인하였다. EDS 분석을 통하여 섬유기판의 표면에 형성된 물질이 Ni임을 알 수 있었다. 전기적 특성을 확인하기 위하여 4-point probe로 무전해 도금을 진행한 섬유기판의 표면저항 및 저항 분포를 확인하기 위한 맵핑을 진행하였다. 무전해 도금의 진행 시간이 길어질수록 전도성이 향상되었음을 확인할 수 있었고, 표면 위치 별 저항의 분포가 균일함을 알 수 있었다. 인장력, 굽힘, 뒤틀림 시험을 통하여 기계적 스트레스로 인한 저항변화를 측정하였다. 그 결과 도금 시간이 길어질수록 유연성 기판의 저항변화가 점점 사라지는 것을 확인하였다. UTM(Universal testing machine)을 이용하여 도금시간 변화에 대한 무전해 도금 기판의 기계적 특성 향상 여부에 대하여 분석하였다. 인장강도는 무전해 도금을 2 시간 동안 진행한 전도성 섬유기판의 경우, 면섬유 기판보다 약 16 MPa 증가하였다. 이러한 결과들을 토대로 Ni-CNT-Fabric 유연기판은 의류 일체형 전도성 기판으로 이용되기에 충분함을 확인하였고, 이러한 연구 결과는 유연기판, 웨어러블 디바이스뿐만 아니라 유연성이 필요한 배터리, 촉매, 태양전지 등에 적용되어 발전에 기여할 수 있을 것으로 기대한다.

• 한국수소및신에너지학회논문집
• /
• 제20권4호
• /
• pp.291-299
• /
• 2009

Ni-plated polytetrafluoroethylene(Ni-PTFE) particles($25{\mu}m$, $500{\mu}m$) were prepared by using nickel electroless plating. The Ni content in Ni-PTFE particles increased with increasing the amount of reduction agent. At about 53 wt% Ni content, $25{\mu}m$ Ni-PTFE particles showed conductivity of 320S/m. The Ni-PTFE particles were formed into the Ni-PTFE plate using heat treatment at $350^{\circ}C$ under $10{\sim}1000kg/cm^2$. The Ni-PTFE plate displayed the high conductivity of 5100S/m due to the formation of 3-dimentional Ni network. The plate was used as an electrode in an alkaline fuel cell(AFC). In terms of the current density, the Ni-PTFE electrode having higher Ni content(53 wt%) showed improved performance.

• 한국분말재료학회지
• /
• 제14권2호
• /
• pp.108-115
• /
• 2007

Cu-Ni-P alloy nano powders were fabricated by the electrical explosion of electroless Ni plated Cu wires. The effect of applied voltage on the explosion was examined by applying pulse voltage of 6 and 28 kV, The estimated overheating factor, K, were 1.3 for 6 kV and 2.2 for 28 kV. The powders produced with pulse voltage of 6 kV were composed of Cu-rich solid solution, Ni-rich solid solution, and $Ni_3P$ phase. While, those produced with 28 kV were complete Cu-Ni-P solid solution and small amount of $Ni_3P$ phase. The initial P content of 6.5 at.% was reduced to 2-3 at.% during explosion due to its high vapour pressure.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 추계학술대회 논문집 Vol.19
• /
• pp.235-236
• /
• 2006

The contact resistance and grain boundary potential barrier of ceramic $BaTiO_3$ PTCR were investigated. The electroless plated Ni, evaporated Al, and Ag paste were chosen as electrode materials of PTCR device for comparison analysis before and after heat treatment. The contact resistance of electrode were measured by electrometer (dc), digital multimeter (dc), and LCR meter (ac). In the case of Al electroded samples, the heat treatment and protective oxide layer had high resistance and effect on the stability of PTCR effect against contact resistance degradation, but the Ag-paste had comparably high contact resistance before heat treatment and decreased after heat treatment with safe. On the other hand, the samples with electroless plated Ni electrode had good properties of contact resistance against aging.

• 한국표면공학회지
• /
• 제19권2호
• /
• pp.31-43
• /
• 1986

The properties of the electroless nickel deposit mainly depends on the pH of the bath, the plating temperature, and the molar ratio of nickel to hypophosphite but they are also affected by its formulation and concentration of complexing and buffering agents. According to changeing the concentration of triethanolamine and boric acid, phosphorous contents, microsturcture, crystalline, hardness and wear resistance of deposits obtained from ammoniacal alkaline bath were investigated by EPMA, differential thermal analyser, X-ray diffractometer and wear tester. The results are as follows; (1) Increasing concentration of triethanolamine in the bath, the deposits is slightly inclined to increase its phosphorous content(3.7% P). (2) In the as-plated state, the deposits are not crystallized state but they are thermally unstable phase, and they are crystallized with precipitating $Ni_3P$ at 400$^{\circ}C$. (3) The deposit containing 2.3% P has higher hardness value in the as plated and heat treated state at below 300$^{\circ}C$ than those of 3.7% phosphorous deposit (1090Hk). But in the case of heat treating at 400$^{\circ}C$, the former has lower hardness value (1000Hk) than the latter and has remarkably Ni(III) orientation by heat treatment. (4) The 3.7% phosphorous deposit heat treated at 400$^{\circ}C$ has better wear resistance than hard chromium plating.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2009년도 춘계학술발표대회 논문집
• /
• pp.230-234
• /
• 2009

It is significant technique to increase competitiveness that solar cells have a high energy conversion efficiency and cost effectiveness. When making high efficiency crystalline Si solar cells, evaporated Ti/Pd/Ag contact system is widely used in order to reduce the electrical resistance of the contact fingers. However, the evaporation process is no applicable to mass production because high vacuum is needed. Furthermore, those metals are too expensive to be applied for terrestrial applications. Ni/Cu/Ag contact system of silicon solar cells offers a relatively inexpensive method of making electrical contact. Ni silicide formation is one of the indispensable techniques for Ni/Cu/Ag contact sytem. Ni was electroless plated on the front grid pattern, After Ni electroless plating, the cells were annealed by RTP(Rapid Thermal Process). Ni silicide(NiSi) has certain advantages over Ti silicide($TiSi_2$), lower temperature anneal, one step anneal, low resistivity, low silicon consumption, low film stress, absence of reaction between the annealing ambient. Ni/Cu/Ag metallization scheme is an important process in the direction of cost reduction for solar cells of high efficiency. In this article we shall report an investigation of rapid thermal silicidation of nickel on silngle crystalline silicon wafers in the annealing range of $350-390^{\circ}C$. The samples annealed at temperatures from 350 to $390^{\circ}C$ have been analyzed by SEM(Scanning Electron Microscopy).

• 한국수소및신에너지학회논문집
• /
• 제27권3호
• /
• pp.306-310
• /
• 2016

In Na-base Battery for ESS, ${\alpha}-Al_2O_3$ and metal bonding was used to prevent direct reaction between electrolyte and electrode. The hard metal was metalized at $1600^{\circ}C$ in a flowing hydrogen gas for high bonding strength. In this study, instead of hard metal metalizing, Ni was plated on ${\alpha}-Al_2O_3$ by electroless Ni plating technique and then bonded with metal. To enhance the bonding strength, surface of ${\alpha}-Al_2O_3$ was treated with $H_3PO_4$. The effects of strength and leakage of joining as a function of acid treatment time on ${\alpha}-Al_2O_3$ are described.

• Journal of Electrochemical Science and Technology
• /
• 제11권2호
• /
• pp.155-164
• /
• 2020

Here we report our preliminary results about nickel phosphide (Ni-P) electroless coating on the surface of cellulose paper (CP) and its feasibility as the anode for lithium (Li) batteries. In particular, CP can act as a flexible skeleton to maintain the mechanical structure, and the Ni-P film can play the roles of both the anode substrate and the active material in Li batteries. Ni-P films with different P contents were plated uniformly and compactly on the microfiber strands of CP. When they were tested as the anode for Li battery, their theoretical capacity per physical area was comparable to or higher than hypothetical pure graphite and P film electrodes having the same thickness. After the large irreversible capacity loss in the first charge/discharge process, the samples showed relatively reversible charge/discharge characteristics. All samples showed no separation of the plating layer and no detectable micro-cracks after cycling. When the charge cut-off voltage was adjusted, their capacity retention could be improved significantly. The electrochemical result was just about the same before and after mechanical bending with respect to the overall shape of voltage curve and capacity.

• 한국분말재료학회지
• /
• 제24권3호
• /
• pp.242-247
• /
• 2017

In this study, the electroless nickel plating method has been investigated for the coating of Ni nanoparticles onto fine Al powder as promising energetic materials. The adsorption of nickel nanoparticles onto the surface of Al powders has been studied by varying various process parameters, namely, the amounts of reducing agent, complexing agent, and pH-controller. The size of nickel nanoparticles synthesized in the process has been optimized to approximately 200 nm and they have been adsorbed on the Al powder. TGA results clearly show that the temperature at which oxidation of Al mainly occurs is lowered as the amount of Ni nanoparticles on the Al surface increases. Furthermore, the Ni-plated Al powders prepared for all conditions show improved exothermic reaction due to the self-propagating high-temperature synthesis (SHS) between Ni and Al. Therefore, Al powders fully coated by Ni nanoparticles show the highest exothermic reactivity: this demonstrates the efficiency of Ni coating in improving the energetic properties of Al powders.

• 한국결정성장학회지
• /
• 제25권5호
• /
• pp.193-198
• /
• 2015

본 연구에서는 전자파 차폐형 MCT(multi cable transit)의 인서트블록에 사용되는 유연성 EPDM(ethylene propylene diene monomer)고무 상에 무전해 도금을 이용하여 니켈도금을 실시하였다. 도금욕의 공정변수 조절 즉 pH 및 온도에 따라 Ni 도금층의 결정성 및 부착력이 결정되었다. pH와 온도를 달리하여 합성 한 결과 pH 7 및 8, $60{\sim}70^{\circ}C$에서 얻은 도금막들에서 잘 발달된 결정상과 높은 전기 전도도를 가짐을 알 수 있었다. pH 7, $70^{\circ}C$에서 도금 시 가장 높은 부착력 및 전기전도도를 얻을 수 있었으며, 또한 400 MHz~1 GHz 범위에서 우수한 전자파 차단능을 얻을 수 있었다.