• Composites Research
• /
• 제20권5호
• /
• pp.43-48
• /
• 2007

전자기파의 흡수와 간섭 문제는 상업적, 군사적 용도에서 중요한 문제로 다루어져 왔다. 스텔스 기술은 전자기파 흡수 기술의 가장 전형적인 적용 방법 중에 하나이다. 본 연구는 유전성 및 자성 손실을 함유한 복합성의 필러를 개발하고자 시작되었다. 전도성 나노 소재인 탄소나노섬유 (CNFs)에 자성을 부여하기 위해 두 가지의 니켈-인과 니켈-철을 무전해 도금을 적용하여 각각 코팅하는 실험에 성공하였다. 제작된 복합 소재의 미세 구조를 SEM/TEM을 통해 관찰하였고, 이들의 성분 분석(EDS/ELLS)을 수행하였다. 코팅 층의 평균 두께는 약 $50\;{\sim}\;100\;nm$의 결과를 나타내었으며, 코팅 층의 성분은 Ni-6wt%P와 Ni-70wt%Fe의 결과를 각각 나타내었다.

• 한국염색가공학회:학술대회논문집
• /
• 한국염색가공학회 2004년도 추계학술발표회 논문집
• /
• pp.238-244
• /
• 2004

In this study we have examined Copper and Nickel double metal layer on the synthetic fabrics by electroless chemical plating. We have focused on the shielding effect of the four kinds of woven and none-woven structure against electromagnetic fields. The shielding effectiveness of Copper and Nickel double metal layer showed between 90dB and 70dB, which are closely related to the fabric structure, that is cover factor and density. The more dense, The better shielding effect.

• Bulletin of the Korean Chemical Society
• /
• 제32권5호
• /
• pp.1630-1634
• /
• 2011

Electroless plating of metallic nickel on carbon fiber surfaces was carried out to control specific electric resistivity of the fibers, and the effects of the nickel content and coating thickness on the electric properties were studied. The structural and surface properties of the carbon fibers were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS). The specific resistivity of the fibers was measured using a four-point probe testing method. From the XPS results, the oxygen and Ni atomic ratio of the fibers was greatly enhanced as the plating time increased. Additionally, it was observed that the specific electric resistivity decreased considerably in the presence of metallic nickel particles and with the formation of nickel layers on carbon fibers.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2009년도 춘계학술발표대회 논문집
• /
• pp.214-219
• /
• 2009

In high-efficiency crystalline silicon solar cells, If high-efficiency solar cells are to be commercialized. It is need to develop superior contact formation method and material that can be inexpensive and simple without degradation of the solar cells ability. For reason of plated metallic contact is not only high metallic purity but also inexpensive manufacture. It is available to apply mass production. Especially, Nickel, Copper and Silver are applied widely in various electronic manufactures as easily formation is available by plating. The metallic contact system of silicon solar cell must have several properties, such as low contact resistance, easy application and good adhesion. Ni is shown to be a suitable barrier to Cu diffusion as well as desirable contact metal to silicon. Nickel monosilicide(NiSi) has been suggested as a suitable silicide due to its lower resistivity, lower sintering temperature and lower layer stress than $TiSi_2$. Copper and Silver can be plated by electro & light-induced plating method. Light-induced plating makes use the photovoltaic effect of solar cell to deposite the metal on the front contact. The cell is immersed into the electrolytic plating bath and irradiated at the front side by light source, which leads to a current density in the front side grid. Electroless plated Ni/ Electro&light-induced plated Cu/ Light-induced plated Ag contact solar cells result in an energy conversion efficiency of 14.68 % on $0.2{\sim}0.6{\Omega}{\cdot}cm,\;20{\times}20mm^2$, CZ(Czochralski) wafer.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2009년도 추계학술발표대회 논문집
• /
• pp.350-355
• /
• 2009

The crysralline silicon solar cell where the solar cell market grows rapidly is occupying of about 85% or more high efficiency and low cost endeavors many crystalline solar cells. The fabricaion process of high efficiency crystalline silicon solar cells necessitate complicated fabrication processes and Ti/Pd/AG contact, This metal contacts have only been used in limited areas in spite of their good srability and low contact resistance because of expensive materials and process. Commercial solar cells with screen-printed solar cells formed by using Ag paste suffer from loe fill factor and high contact resistance and low aspect ratio. Ni and Cu metal contacts have been formed by using electroless plating and light-induced electro plating techniques to replace the Ti/Pd/Ag and screen-printed Ag contacts. Copper and Silver can be plated by electro & light-induced plating method. Light-induced plating makes use the photovoltaic effect of solar cell to deposit the metal on the front contact. The cell is immersed into the electrolytic plating bath and irradiated at the front side by light source, which leads to a current density in the front side grid. Electroless plated Ni/ Electro&light-induced plated Cu/ Light-induced plated Ag contact solar cells result in an energy conversion efficiency of 16.446 % on 0.2~0.6${\Omega}$ cm, $20{\times}20mm^2$, CZ(Czochralski) wafer.

• 한국수소및신에너지학회논문집
• /
• 제3권2호
• /
• pp.9-15
• /
• 1992

Electroless copper plating method using an alkaline bath have been employed in copper coating of the (LM)Ni4.5Co0.1MnO.2A10.2 hydrogen storage alloy powders for electrode preparation. The plating were conducted without any pretreatment of alloy powders. For the preparation of the electrodes, about 0.12g of the copper coated alloy powder (copper to alloy ratio 1/3 by weight) was compacted with pressure of 6 tons/cm2 at room temperature. The disk-type compacts had a diameter of 10mm and thickness of about 0.24mm. The electrode characteristics were examined through SEM observations and electrochemical measurements in a half cell. The electrochemical measurement showed that the maximum discharge capacity of the electrodes prepared by using alkaline bath were 245mAh per gram of coated alloy (327mAh per gram of alloy) and appeared a considerable degradation with increasing number of cycles. The decrease of the discharge capacity after 100 cycles was about 30% It can be suggested that, with a slight of improvement, this electroless copper plating method could be applied to the preparation of the rare earth-nickel based alloy electrode.

• 한국표면공학회지
• /
• 제40권2호
• /
• pp.70-76
• /
• 2007

Ni-P-SiC composite coating layers were prepared by electroless plating method and their deposition rate, codeposition of SiC, morphology, surface roughness, hardness, wear and friction properties were investigated. The deposition rate was kept almost constant independent of the concentration of SiC in the plating solution and the codeposition of SiC in the composite coating layer increased with increased concentration of SiC in the plating solution except the early stage. Vickers microhardness increased with respect to the increased codeposition of SiC and the heat treatment at $300^{\circ}C$ in air for 1 hour. It was found that the wear volume decreased with increased up to 50 wt.% of SiC codeposition, and that friction coefficient increased gradually with increased codeposition of SiC. Considering the wear and the friction behaviors, the composite coating layer obtained by using 50 wt.% of SiC codeposition is desirable for the practical application for anti-wear and anti-friction coatings.

• Korean Chemical Engineering Research
• /
• 제59권2호
• /
• pp.269-275
• /
• 2021

메탄의 부분 산화반응을 위해 규칙적인 메조기공을 갖는 실리카를 지지체로 한 니켈 촉매를 제조하였다. 니켈 플레이팅(Nickel plating) 방법을 이용하여 촉매 제조 시 기존 함침 촉매 제조법과 달리 니켈이 실리카 표면에 도포된다. 이때 니켈이 고분산 되어 안정적인 니켈입자를 형성하게 된다. 니켈 플레이팅 촉매의 경우, TEM-EDS 분석에서 니켈이 매우 고분산 된 것을 확인할 수 있었다. 이러한 고분산된 촉매로 메탄 부분산화 반응 시 기존 함침촉매와는 달리 니켈의 소결과 탄소침적이 상대적으로 적어 촉매의 비활성화가 매우 낮았다. 팔라듐은 환원 조촉매로서의 역할을 하여, 메탄 전환율과 생성된 합성가스의 H2/CO 비 관점에서 우수한 반응 성능을 보이는 것을 확인 할 수 있었다.

• 전기화학회지
• /
• 제10권2호
• /
• pp.88-93
• /
• 2007

Nano-sized Sn particles were coated with Ni-P layer using an electroless deposition method and their anodic performance was tested for lithium secondary batteries. Uniform coating layers were obtained, of which the thickness was controlled by varying the $Ni^{2+}$ concentration in the plating bath. It was found that the Ni-P layer plays two important roles in improving the anodic performance of Sn powder electrode. First, it prevents the inter-particle aggregation between Sn particles during the charge/discharge process. Second, it provides an electrical conduction pathway to the Sn particles, which allows an electrode fabrication without an addition of conductive carbon. A pseudo-optimized sample showed a good cyclability and high capacity ($>400mAh\;g^{-1}$) even without conductive carbon loading.

• 한국염색가공학회지
• /
• 제10권2호
• /
• pp.8-17
• /
• 1998

In this study we have examined electroless chemical plating on the plasma grafted poly [ethylene terephathalate］(PET) fabric in order to improve the interfacial adhesion between metal and fiber. The vapour phase of acrylic acid introduced on the PET surface and the graft polymerization was carried out by using cold plasma, resulting in the grafting yield of 0.8-1.3 wt％. The carboxyl group of the plasma grafted was identified by FT-IR-ATR spectra. The Interfacial adhesion was related to the carboxyl group. After electroless chemical plating of nickel, it showed that the more the carboxyl, the better the interfacial adhesion. Comparing to the untreated, the plasma grafted fabric showed fairly good interfacial adhesion(5B grade, ASTM D3359) . The shielding effect of electromagnetic wave showed 95dB. The shielding effect depends on the fabric structure, the surface structure, and the cross sectional shape of fibers. The dense fabric structure, the etched surface like a microcrater, and the trigonal cross sectional shape were prefered.