• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.277-277
• /
• 2012

PCDTBT (Poly[N-9''-hepta-decanyl-2,7-carbazole-alt-5,5-(4',7'-di-2-thienyl-2',1',3'-benzothiadiazole)]) is an attractive material as a semiconducting polymer for organic thin film transistor (OTFT) and organic solar cell (OSC). High power conversion efficiency (~6%) under simulated AM 1.5G solar illumination of bulk-heterojunction solar cell with PCDTBT and [6,6]-phenyl C60 butyric acid methyl ester (PC61BM) blend was reported. In OSC, it is known that the band alignment at the interface between donor and acceptor is critical. Therefore, we studied the interfacial electronic structures of PCDTBT and PC61BM. The polymers are deposited by electro-spray on gold and In-situ x-ray and ultraviolet photoelectron spectroscopy measurements revealed the interfacial electronic structures. We obtained the energy level alignment between two materials and the different interface formation was observed with different deposition order.

• Archives of Pharmacal Research
• /
• v.28 no.10
• /
• pp.1177-1182
• /
• 2005

The hepatotoxic effects of 1-bromopropane (1-BP) and its conjugation with glutathione were investigated in male ICR mice. A single dose (1000 mg/kg, po) of 1-BP in corn oil to mice significantly increased serum activities of alanine aminotransferase and aspartate aminotransferase. Glutathione (GSH) content was dose-dependently reduced in liver homogenates 12 h after 1-BP treatment. In addition, 1-BP treatment dose-dependently increased levels of S-pro-pyl GSH conjugate at 12 h after treatment, as measured by liquid chromatography-electro-spray ionization tandem mass spectrometry. The GSH conjugate was maximally increased in liver at 6 h after 1-BP treatment (1000 mg/kg), with a parallel depletion of hepatic GSH content. Finally, 1-BP induced the production of malondialdehyde in liver. The present results suggest that 1-BP might cause hepatotoxicity, including lipid peroxidation via the depletion of GSH, due to the formation of GSH conjugates in male ICR mice.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.675-675
• /
• 2013

CIGS thin films have received a great attention as a promising material for solar cells due to their high absorption coefficient, appropriate bandgap, long-term stability, and low cost production. CIGS thin films have been deposited by various methods such as co-evaporation, sputtering, spray pyrolysis and electro-deposition. In this study, Cu(In,Ga)Se2(CIGS) thin films were prepared using a single quaternary target by rf magnetron sputtering. The effect of sulfurization on the structural, compositional and electrical properties of the films was examined in order to develop the deposition process. An optimal sulfurization process will be selected for the preparation of CIGS thin films with good structural, optical and electrical properties by applying various sulfurization processes. In addition, the electrical properties of CIGS thin films were investigated by post-deposition annealing process. The carrier concentration of CIG(SSe) thin films after sulfurization was increased from $10^{14}cm^{-3}$ to $10^{16}cm^{-3}$ and the resistivity was increased from 10 ${\Omega}cm$ to $10^3$ ${\Omega}cm$. It is confirmed that CIG(SSe) thin films prepared at optimal deposition condition have similar atomic ratio to the target value after sulfurization.

• BMB Reports
• /
• v.37 no.4
• /
• pp.460-465
• /
• 2004

A 16-residue polypeptide model with the sequence acetyl-YALSLAATLLKEAASL-OH was derived by rational de novo peptide design. The designed sequence consists of amino acid residues with high propensity to adopt an alpha helical conformation, and sequential order was arranged to produce an amphipathic surface. The designed sequence was chemically synthesized using a solid-phase method and the polypeptide was purified by reverse-phase liquid chromatography. Molecular mass analysis by electro-spray ionization mass spectroscopy confirmed the correct designed sequence. Structural characterization by circular dichroism spectroscopy demonstrated that the peptide adopts the expected alpha helical conformation in 50% acetonitrile solution. Liposome binding assay using Small Unilamellar Vesicle (SUV) showed a marked release of entrapped glucose by interaction between the lipid membrane and the tested peptide. The channel-forming activity of the peptide was revealed by a planar lipid bilayer experiment. An analysis of the conducting current at various applied potentials suggested that the peptide forms a cationic ion channel with an intrinsic conductance of 188 pS. These results demonstrate that a simple rational de novo design can be successfully employed to create short peptides with desired structures and functions.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.16 no.3
• /
• pp.116-120
• /
• 2006

We have investigated plasma spray coated $Al_2O_3$ layers on Al-60 series substrates for development of wafer electrostatic chuck in semiconductor dry etching system. Samples were prepared without/with cooling bar on backside of samples, at various distances, and with different powder feed rates. There were many cracks and pores in the $Al_2O_3$ layers coated on Al-60 series substrates without cooling bar on the backside of samples. But the cracks and pores were almost disappeared in the $Al_2O_3$ layers on Al-60 series substrates coated with cooling bar on the back side of samples, 15 g/min. powder feed rate and various 60, 70, 80 mm working distances. Then the surface morphology was not changed with various working distances of 60, 70, 80 mm. When the powder feed rate was changed from 15 g/min to 20 g/min, the crack did not appear, but few pores appeared. Also the $Al_2O_3$ layer was coated with many small splats compared with $Al_2O_3$ layer coated with 15 g/min powder feed rate. The deposited rate of $Al_2O_3$ layer was higher when the process was done without cooling bar on the back side of sample than that with cooling bar on the back side of sample.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.42 no.1
• /
• pp.15-19
• /
• 2009

A simple and sensitive method for erythromycin quantification by liquid chromatography electrospray mass spectrometry (LC-MS/MS) in fishery products was developed. Samples were extracted by liquid-liquid extraction using 70% acetonitrile. Lipids were removed by acetonitrile saturated hexane. LC separation was performed on a Shiseido UG C-18 column ($150\;mm{\times}2.0\;mm$ internal diameter.) with a gradient system of 0.2% acetic acid-acetonitrile containing 0.2% acetic acid as a mobile phase at flow rate of 0.2 mL/min. The mass spectrometer was operated in selected reaction monitoring with positive electro-spray interface. Transitions were monitored a m/z $734{\to}577$ and $734{\to}158$, with m/z $734{\to}577$ chosen for quantification. Recovery of erythromycin from fish and shrimp fortified at the 10 ng/mL, 50 ng/mL and 100 ng/mL were 91.6-109.4%, 84.4-111.2% and 98.8-109.6% with high precision, respectively. Limits of quantification and limits of detection of erythromycin in both fish and shrimp were 10.0 ng/mL and 1.0 ng/mL, respectively. This analysis method for erythromycin has been proposed for registration in the Korean Official Methods of Food Analysis and has been utilized for fishery products analysis by the Korea Food and Drug Adminstration and the National Fisheries Products Quality Inspection Service.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.5
• /
• pp.517-521
• /
• 2012

Carbon nanotubes (CNTs) have been regarded as a promising material for the fabrication of flexible conductors such as transparent electrodes, flexible heaters, and transparent speakers. In this study, a multiwalled carbon nanotube (MWCNT) film was deposited on a polyethylene terephthalate (PET) substrate using a spraying technique. MWCNTs were dispersed in water using sodium dodecyl sulfate (SDS). To evaluate the effect of the weight ratio between SDS and MWCNTs on the electromechanical properties of the film, direct tensile tests and optical strain measurement were conducted. It was found that the CNT film hardly affected the mechanical behavior of CNT/PET composite films, while the electrical behavior of the CNT film was strongly affected by the SDS concentration in the CNT film. The electrical resistance of CNT/PET films gradually increased with the strain applied to the PET substrate, even up to a large strain that ruptured the substrate.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.382-382
• /
• 2012

CIGS thin films have received great attention as a promising material for solar cells due to their high absorption coefficient, appropriate bandgap, long-term stability, and low cost production. CIGS thin films are deposited by various methods such as co-evaporation, sputtering, spray pyrolysis and electro-deposition. The deposition technique is one of the most important processes in preparing CIGS thin film solar cells. Among these methods, co-evaporation is one of the best technique for obtaining high quality and stoichiometric CIGS films. However, co-evaporation method is known to be unsuitable for commercialization. The sputtering is known to be very effective and feasible process for mass production. In this study, CIGS thin films have prepared by rf magnetron sputtering using a $Cu(In_{1-x}Ga_x)Se_2$ single quaternary target without post deposition selenization. This process has been examined by the effects of deposition parameters on the structural and compositional properties of the films. In addition, we will explore the influences of substrate temperature and additional annealing treatment after deposition on the characteristics of CIGS thin films. The thickness of CIGS films will be measured by Tencor-P1 profiler. The crystalline properties and surface morphology of the films will be analyzed using X-ray diffraction and scanning electron microscopy, respectively. The optical properties of the films will be determined by UV-Visible spectroscopy. Electrical properties of the films will be measured using van der Pauw geometry and Hall effect measurement at room temperature using indium ohmic contacts.

• Food Science and Biotechnology
• /
• v.18 no.1
• /
• pp.113-117
• /
• 2009

A method was developed using enhanced liquid chromatography coupled with electrospray ionization mass spectrometry for the analysis and quantitation of 2 main potato glycoalkaloids, $\alpha$-chaconine, and $\alpha$-solanine, without any pre-concentration or derivatisation steps. Calibration curves generated by this technique exhibited a linear dynamic range from 0.025 to $50{\mu}g/mL$ and from 0.05 to $50{\mu}g/mL$ for $\alpha$-chaconine and $\alpha$-solanine, respectively. Matrix effects were evaluated by comparing calibration curves measured in matrix-matched and solvent-based systems. Ion suppression due to matrix effects was weak and extraction recoveries of 88 to 114% were obtained in different sample matrices spiked with analyte concentrations ranging from 15 to $35{\mu}g/mL$. Potatoes that had been genetically modified to tolerate glufosinate contained the same glycoalkaloid levels as their non-transgenic counterpart. We suggest complementing compositional comparison assessment strategy by validating quantitative analytical methods for the toxic glycoalkaloids in potato plants.

• Applied Chemistry for Engineering
• /
• v.31 no.5
• /
• pp.502-508
• /
• 2020

Dual drug-eluting stents (DES) is a primary treatment method for coronary arterial diseases in current interventional cardiology practice. However, their pathological results according to the sequence of coating of drugs have not been reported yet. The peptide-dopamine dissolved in acetonitrile was coated onto the Chonnam National University Hospital (CNUH) stent using an electrospinning coating machine. For secondary coating (e.g., sirolimus coating, designated as SPS), sirolimus (SRL) and poly lactic-glycolic acid (PLGA) were mixed in tetrahydrofuran (THF), and the solution was then coated on the CNUH stent that had underwent the primary peptide coating using an electrospinning and spray technique. Next, the peptide-dopamine was coated on the SRL-PLGA coated stent (PSS). In this study, it was confirmed that endothelialization was promoted without being significantly affected by the coating order (SPS or PSS). The sequence of drug and peptide coating may affect the development of restenosis and PSS was effective in the prevention of restenosis compared to that of using SPS.