• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05b
• /
• pp.111-118
• /
• 2002

A new lithium niobate optical modulator with a polymer buffer layer on Ni in-diffused optical waveguide is proposed for the fist time, successfully fabricated and examined at a wavelength of 1.3 mm. By determining the diffusion parameters of Ni in-diffused waveguide to achieve more desirable mode size which is well matched to the mode in the fiber, the detailed results on the achievement of high optical throughput are reported. In addition, the usefulness of polymer buffer layer which can be applicable to a buffer layer in Ni in-diffused waveguide devices is demonstrated. Several sets of channel waveguides fabricated on Z-cut lithium niobate by Ni in-diffusion were obtained and on which coplanar traveling-wave type electrodes with a polymer-employed buffer layer were developed by a conventional fabrication method for characterizing of electro-optical performances of the proposed device. The experimental results show that the measured half-wave voltage is of ~10 V and the total measured fiber-to-fiber insertion loss is of ~6.4 dB for a 40 mm long at a wavelength of =1.3 mm, respectively. From the experimental results, it is confirmed that the polymer-employed buffer layer in LiNbO3 optical modulator can be a substitute material instead of silicon oxide layer which is usually processed at a high temperature of over $300^{\circ}C$. Moreover, the fabrication tolerances by using polymer materials in LiNbO3 optical modulators are much less strict in comparison to the case of dielectric buffer layer.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.780-785
• /
• 2003

Recently the trends in information storage devices need small size, mobility, high capacity, and low power consumption etc. To satisfy those, the development of high performance actuator is an important issue. Compared with general linear actuator for optical disk drive, swingarm type rotary actuator is suitable to design in small form factor and has fast access time for random access. Swingarm actuator is designed considering the structural problem and the actuating force of VCM(Voice Coil Motor). The increase of mass caused by optical components makes vibration problems of swing-arm, therefore resonance frequency should be increased and inertia has to be reduced. ANSYS FEM tool is employed in optimizing swingarm. The VCM is designed using 3-D electro-magnetic analysis, and parameters of magnetic circuit are determined to matte large flux density. The large flux density enables to achieve low power consumption. VCM holder is designed to get the mass balance of total actuator and this balance reduces the magnitude of critical mode relative to pivot bearing, It is expected that swingarm type rotary actuator designed by this method is available to variable type of micro optical disk drives.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.22 no.1
• /
• pp.11-14
• /
• 2012

The AlGaN layer has direct wide bandgaps ranging from 3.4 to 6.2 eV. Nowadays, it is becoming more important to fabricate optical devices in an UV region for the many applications. The high quality AlGaN layer is necessary to establish the UV optical devices. However, the growth of AlGaN layer on GaN layer is difficult due to the lattice mismatch and difference thermal expansion coefficient between GaN layer and AlGaN layer. In this paper, we attempted to grow the LED structure on GaN template by mixed-source HVPE method with multi-sliding boat system. We tried to find the optical and lattice transition of active layer by control the Al content in mixed-source. For the growth of epi layer, the HCl and $NH_3$ gas were flowed over the mixed-source and the carrier gas was $N_2$. The temperature of source zone and growth zone was stabled at 900 and $1090^{\circ}C$, respectively. After the growth, we performed the x-ray diffraction (XRD) and electro luminescence (EL) measurement.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.48 no.5
• /
• pp.571-579
• /
• 1999

In this paper, a Hadamard transform imaging spectrometer(HTIS) is proposed by using a grill spectrometer. And we reconfigure the system by using the grill sectrometer which uses a left cyclic S-matrix instead of the conventional right cyclic one. Then, we model the Hadamard transform imaging spectrometer and apply the mask characteristics compensation method, i.e. $ {T}^{-1}$ method, to complete fast algorithm. Also, through computer simulations the superiority of the proposed system in this paper to the conventional Hadamard transform spectrometer(HTS) is proved and the performance of the two systems are compared by introducing average mean square error(AMSE) as the algebraic criterion.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.04a
• /
• pp.18-22
• /
• 2004

We have investigated the generation of pretilt angle for a nematic liquid crystal (NLC) alignment with rubbing alignment method on polyimide surfaces using thin plastic substrates. It was found that monodomain alignment of NLC is obtained with rubbing alignment method on polyimide surfaces using thin plastic substrates. The NLC pretilt angles generated are about $3^{\circ}$ by the rubbing alignment method on thin plastic substrates, However, the pretilt angle are at about $1.7^{\circ}$ lower on the glass substrate than on thin plastic substrate. Also, EO characteristics of the TN-LCD with a rubbed PI surface based on polymer are almost the same as that of the TN-LCD with a rubbed PI surface based on glass. However, the transmittances of the TN-LCD with a rubbed PI surface based on polymer is less than that with a rubbed PI surface based on glass.

• Transactions on Electrical and Electronic Materials
• /
• v.8 no.3
• /
• pp.135-138
• /
• 2007

In this study, we investigated the electro-optical (EO) characteristic of fringe-field switching (FFS) mode cell by the two kinds of ultraviolet (UV) alignment method on the organic thin film (polyimide: PI). The suitable organic layers for FFS cell and the aligning capabilities of nematic liquid crystal (NLC) using the in-situ photoalignment method were studied; Disclination is observed after conventional photoalignment method for 1h, and in-situ photoalignment method for 1h. Monodomain alignment of the NLC can be observed via insitu photo alignment method for 2 h and 3 h. It is considered that NLC alignment is due to photo-depolymerization of the polymer with oblique non-polarized UV irradiation on PI surface. An unstable V-T curve of UV-aligned FFS-LCD with conventional photoalignment method can be achieved. However, a stable V-T curve of UV-aligned FFS-LCD with in-situ photoalignment method (1 h), and V-T curve of UV-aligned FFS-LCD with in-situ photo alignment method was much stable comparing with that of other UV-aligned FFSLCD's. As a result, more stable EO performance of UV-aligned FFS-LCD with in-situ photoalignment method for 3h is obtained than that of the other UV-aligned FFS-LCD's.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.7A
• /
• pp.719-726
• /
• 2004

In this paper, compensation characteristics of distorted WDM channel due to both chromatic dispersion and self phase modulation (SPM) is numerically investigated under the assumptions of non-uniformly distributed fiber dispersion, in order to inspect the application of mid-span spectral inversion (MSSI) to any exact transmission links. The MSSI is compensation method used in this approach. This method has an optical phase conjugator (OPC) placed in mid-way of total transmission length to compensate distorted WDM channels. It is confirmed that MSSI will become applicable to long-haul WDM systems by controlling input light power of transmission channels, when the averaged dispersion of both fiber sections with respect OPC was varied and distributed unequally each other. Applying MSSI to long-haul WDM system, it is possible to remove all in-line compensator, consequently it will be expected to reducing system cost.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.4
• /
• pp.309-313
• /
• 2011

In this study, we proposed a novel electrode structure for the fringe field switching (FFS) mode LCD and performed a three-dimensional computer simulation to calculate the optical transmittance for the new structure. In the simulation Erickson-leslie equation and Berreman $4{\times}4$ matrix were used for obtaining the director distribution profiles of liquid crystal molecules and the electro-optical characteristics, respectively. Considering the complexity of the motional equation of the liquid crystal molecules, FDM (finite difference method) was used as a numerical method. From the results, We revealed that the light transmission of the newly designed pixel structure is expended to the edge of the pixel electrode. We also confirmed that the light transmittance increased more than 13% compared to that of the conventional electrode structure.

• Korean Journal of Optics and Photonics
• /
• v.14 no.2
• /
• pp.194-199
• /
• 2003

The analysis of operation characteristics of a miniaturized electrostatic electron lens system called an Einzel lens was performed using a simulation tool of FCM method. The potential distributions of Einzel lenses operated both in retarding and accelerating modes show similar features. But the electric fields determined from the potential distributions show opposite directions, which results in different features in the electron beam trajectory in each mode of operation. For the same working distance, focusing voltage in the accelerating mode is higher than that in the retarding mode.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.6 s.109
• /
• pp.546-555
• /
• 2006

In this paper, the numerical methods of finding the optimal position of optical phase conjugator(OPC) and the optimal fiber dispersions are proposed, which are able to effectively compensate overall channels in $8{\times}40$ Gbps WDM system with non zero-dispersion shifted fiber(NZ-DSF) as an optical fiber. And the compensation characteristics in the system with two induced optimal parameters are compared with those in the system with mid-span spectral inversion (MSSI) technique in order to confirm the availability of the proposed methods. It is confirmed that the optimal parameter values induced in this approach are very useful to effectively compensate overall channels in WDM system with OPC. And, it is confirmed that two optimal parameters depend on each other, but less related with the searching procedure. The methods proposed in this research will be expected to alternate with the method of making a symmetrical distribution of power and local dispersion in real optical link which is a serious problem of applying the OPC into multi-channels WDM system.