위성용 전자광학탑재체는 제한된 소모전력 및 우주방사선과 같은 사용 환경에 의해 설계부터 특별한 요구사항을 가지고 있으며, 획득 영상의 품질은 주로 GSD (Ground Sampled Distance), 신호대잡음비(SNR, Signal to Noise Ratio), MTF (Modulation Transfer Function)에 따라 좌우된다. 영상센서의 출력신호에 포함된 잡음 감소를 통한 신호대잡음비 개선을 위하여, 센서에 추가된 프리픽셀(Pre-pixel) 및 다크픽셀(Dark-pixel)을 사용하여 CDS (Corrective Double Sampling) 방식을 통해 영상센서의 잡음 성분을 포함한 오프셋 신호(Offset Signal)를 제거하는 아날로그 신호처리(ASP, Analog Signal Processor) 방법을 제안한다. 또한 센서 제어시스템에서는 영상의 불균일성 처리를 위해 제어시스템의 출력 포트별 게인(Gain), 오프셋, 및 센서의 화소별 특성을 반영한 다양한 방식에 의한 보정 방법이 적용된다. 본 논문에서는 이상 설명한 여러 가지 잡음 개선방법을 시스템 설계 및 운영에 적용하여 위성탑재용 전자광학카메라의 신호대잡음비 향상 방법을 제안하고, 실험을 통해 검증한다.
본 연구에서는 폴리이미드 박막위에서의 수직 및 수평배향에서 혼합액정의 배향 특성에 대해서 연구하였다. 혼합액정은 러빙을 이용하여 배향처리하였으며, 러빙에 사용된 폴리이미드 박막은 알킬기를 Side Chain으로 가진 수직배향용 배향막과 그렇지 배향막으로 나누어서 프리틸트각 특성을 측정하였다. 실험결과 혼합액정을 사용하여 양호한 배향상태를 얻을 수 있었으며, 고온에서의 열 안정성에서도 우수한 특성을 보이는 것을 알 수 있었다. 또한 프리틸트각의 발생 원리를 이해하기 위해서 접촉각 측정을 실시하였으며, 이 둘이 밀접한 상관관계를 갖고 있음을 알 수 있었다
We have studied $90^{\circ}$ twisted nematic (TN) mode driven by fringe electric field, where two polarizers are parallel each other such that the cell shows a black state before a voltage is applied. According to the studies by computer simulation for a LC with negative dielectric anisotropy, the LC twists perpendicular to the horizontal field direction of fringe electric field and the degree of tilt angle is very low, when a voltage is applied. Therefore, the new device exhibits wide viewing angle characteristic due to in-plane switching and high transmittance since the LC director aligns parallel to the polarizer axis.
본 연구에서는 이전에 제안한 stripe형으로 제작된 경사형 대향유지전극구조의 마진 개선과 오방전 감소를 위하여 폐쇄형으로 제작된 경사형 대향유지전극구조를 제안하였다. 제안된 구조는 상판의 유지전극들을 페쇄형으로 패터닝된 유전체층 사이에 Ag 전극을 경사형으로 형성하여 만든 구조이다. 테스트 패널은 250${\mu}m$ 유지전극 간격들을 가지는 제안된 구조와 기존의 유지전극 간격 60${\mu}m$의 ITO 구조를 reference로 하여 제작하였다. 폐쇄형 구조를 reference를 기준으로 이전의 stripe형과 비교했을때 전류가 50${\sim}$64% 증가하여 효율이 18% 감소하였지만 마진이 25V 증가하였고 휘도가 최대 44% 증가하였다. 패쇄형 구조가 stripe형 구조에 비해 효율이 감소하였지만 기존의 면방전형 구조에 비해 최대 146%의 효율 증가를 보였으며 동일전압에서 stripe 구조에 비해 높은 휘도와 넓어진 마진을 가졌다.
Mg(4 mole%):LiNb$O_3$에서 제 2고조파발생특성을 온도와 직류전장의 함수로 측정하여, Mg:LiNb$O_3$ 결정의 공간적 균일성을 조사 하였다. 발생된 제2고조파및의 세기가 위상정합된 상태의 최대값으로부터 최초로 0이 되는 온도가 결정의 광축으로 가해준 직류전장의 변화에 선형적으로 변위함을 관찰하였다. 이로부터, 최초로 Mg가 4mole% 첨가된 Mg:LiNb$O_3$ 의 전기광계수가 Congruent LiNb$O_3$의 해당하는 값보다 1.5배가 더 큼을 알 수 있었다.
Indium tin oxide (ITO) used a transparent electrode of a photoelectric device has a low sheet resistance and a high transmittance. However, ITO is disadvantageous in that the process cost is expensive, and the process time is long. Silver nanowires (AgNWs) transparent electrodes are based on a low cost solution process. In addition, it has attracted attention as a next-generation transparent electrode material that replaces ITO because it has similar electrical and optical characteristic to ITO, it is noted as a. AgNW thin films are mainly produced by spin-coating. However, the spin-coating process has a disadvantage of high material loss. In this study, the material loss was reduced by using about 2~10 ㎕ of AgNW solution on a (25 × 25) ㎟ substrate using the shear-coating method. It was also possible to align AgNWs in the drag direction by dragging the meniscus of the solution. The electro-optical properties of the AgNW thin film were adjusted by changing the experimental parameters that the amount of AgNWs suspension, the gap between the substrate and the blade, and the coating speed. As a result, AgNW thin films with a transmittance of 90.7 % at a wavelength of 550 nm and a sheet resistance of 15 Ω/□ was deposited and exhibited similar properties to similar AgNW transparent electrodes studied by other researchers.
Q-스위칭은 셔터나 다른 광학소자를 레이저 광 공진기 내에 넣어 광이 공진기 내에서 발진하는데 손실을 유발하고, 충분한 반전분포가 활성 매질 내에서 생성되면 순간적으로 셔터를 열어 공진기 내에 축적된 에너지가 매우 강한 빛으로 방출되게 하는 것이다. 이와 같이 Q-스위칭은 레이저 공진기의 Q--factor를 감소시켰다가 갑자기 증가시키는 것이다. 레이저 Q-스위칭의 방법에는 mechanical switching 방법, electro-optic switching 방법, switching by saturable absorber 방법, acousto-optic switching 방법 등 크게 4가지가 쓰이고 있다. 이들 중 전기광학적인 효과에 의한 전기적인 전환은 짧은 펄스폭의 Q-스위칭 펄스를 생성할 수 있기 때문에 널리 사용되고 있다. 따라서, 전기광학효과의 특성을 가진 Pockel cell은 Q--switch로 사용하기 적합한 것으로 알려져 있다. 본 연구에서는 포켈스 셀 Q-스위치용 구동 장치를 스위칭 소자인 FET와 PIC 마이크로프로세서 및 펄스 트랜스로 설계, 제작하고, 펄스형 Nd:YAG 레이저 시스템에 적용하여 Q-스위치의 동작 특성을 조사, 연구하였다. 또한, 이 Q-스위치를 통하여 출력된 Nd:YAG 레이저 빔의 측정치를 이론적 계산에 의해 구해진 예상치와 비교하여 Q-스위칭 된 레이저 빔의 특성을 분석하였다.
Transactions on Electrical and Electronic Materials
/
제8권3호
/
pp.135-138
/
2007
In this study, we investigated the electro-optical (EO) characteristic of fringe-field switching (FFS) mode cell by the two kinds of ultraviolet (UV) alignment method on the organic thin film (polyimide: PI). The suitable organic layers for FFS cell and the aligning capabilities of nematic liquid crystal (NLC) using the in-situ photoalignment method were studied; Disclination is observed after conventional photoalignment method for 1h, and in-situ photoalignment method for 1h. Monodomain alignment of the NLC can be observed via insitu photo alignment method for 2 h and 3 h. It is considered that NLC alignment is due to photo-depolymerization of the polymer with oblique non-polarized UV irradiation on PI surface. An unstable V-T curve of UV-aligned FFS-LCD with conventional photoalignment method can be achieved. However, a stable V-T curve of UV-aligned FFS-LCD with in-situ photoalignment method (1 h), and V-T curve of UV-aligned FFS-LCD with in-situ photo alignment method was much stable comparing with that of other UV-aligned FFSLCD's. As a result, more stable EO performance of UV-aligned FFS-LCD with in-situ photoalignment method for 3h is obtained than that of the other UV-aligned FFS-LCD's.
The purpose of this study was to evaluate the fracture characteristics and the effect of resin bonding of laminate porcelain. In order to characterize the indentation-induced crack, Young's moduli and characteristic indentation dimensions were measured. The fatigue life under three point flexure test was measured using the electro-dynamic type fatigue machine, and the crack propagation with thermocycling was investigated on the condition of 15 second dwell time each in $5^{\circ}C\;and\;55^{\circ}C$ bath. The Vickers indentation pattern and the fracture surface were examined by an optical microscope and a scanning electron microscope (SEM). The results obtained were summarized as follows ; 1. Young's moduli(E) of the laminate porcelain and the resin cement used in this experiment were $62.56{\pm}3.79GPa$ and $15.01{\pm}0.12GPa$, respectively. 2. The initial crack size of the laminate porcelain was $69.19{\pm}5.94{\mu}m$ when an indentation load of 9.8N was applied, and the fracture toughness was $1.065{\pm}0.156MPa\;m^{1/2}$. 3. The fatigue life of laminate porcelain showed the constant fracture range at the stress level 27.46-35.30MPa. 4. When a cyclic flexure load was applied, the fatigue life of resin-bonded laminate porcelain was more decreased than that of laminate porcelain. 5. When a thermocycling was conducted, the crack growth rate of resin-bonded laminate porcelain was more increased than that of laminate porcelain. 6. Fracture surface showed the radial crack, the lateral crack, and the macroscopic crack branching region beneath the plastic deformation region when an indentation load of 9.8N was applied.
Recently, it is widely studied to liquid crystal (LC) alignment using ion-beam exposure. Because conventional rubbing method has some problems such as defects from dust and electrostatic charges and rubbing scratch during rubbing process. Moreover rubbing method needs cleaning process to remove these defects. Therefore rubbing-free techniques like ion-beam method are strongly required. We studied LC alignment by controlling ion-beam irradiation angles and electro-optical (EO) characteristics of twisted nematic LC on the polyimide surface. In this experiment, a good uniform alignment of the nematic liquid crystal (NLC) with the ion-beam exposure on the polyimide (PI) surface was observed. We also achieved low pretilt angle as function of ion-beam irradiation angles. X-ray photoelectron spectroscopic (XPS) analysis provided chemical evidence for LC alignment by controlling ion-beam irradiation angles. In addition, it can be achieved the good EO properties of the ion-beam-aligned twisted nematic liquid crystal display (TN-LCD) on PI surface. Some other experiments results and discussion will be included in the presentation.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.