• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.26-26
• /
• 2010

EGW process has been applied to joining of ship block with vertical-up position at high production rate. The workability of EGW, however, has been interrupted by too much slag production. Two electrodes EGW showed more severe workability than that of one electrode EGW. Therefore, to understand the effect of discharge amount of EGW slag on workability and mechanical properties, two different slag discharge amount have been controlled at the same welding conditions. The results are as follows; 1) Workability has been improved by any additional slag discharge. 2) Mechanical properties have been deteriorated with any additional slag discharge. 3) Chemical compositions of weld metal have been changed by any additional slag discharge.

• Proceedings of the KWS Conference
• /
• 2005.11a
• /
• pp.65-66
• /
• 2005

In order to evaluate disbonding properties caused by hydrogen on the Electro Slag Strip Welding for 1.25Cr-0.5Mo steel, two kinds of welding consumables were selected and tested under the disbonding condition of $97.2kgf/cm^{2}$ at $425^{\circ}C$. Chemical composition of the welds showed that they have similar chemical compositions. The microsturucture investigation, however, indicated that 'A' weld has high ratio of coarse grain area, while B weld has low. Disbonding results showed that high ratio coarse grain welds showed unacceptable, while low ratio coarse grain welds showed acceptable.

• Proceedings of the KWS Conference
• /
• 1992.10a
• /
• pp.68-72
• /
• 1992

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1123-1124
• /
• 2011

본 논문에서는 ESW(Electro slag welding)의 용접을 위한 해석을 수행하였다. 특히, 열전달 해석을 통하여 부재내부에 발생하는 온도분포에 대한 해석을 수행하였으며, 이를 입력조건으로 하여 구조해석을 수행함으로써, 최종적은 부재내의 최고온도와 최대 변형량을 구할 수 있었다.

• Proceedings of the KWS Conference
• /
• 2002.10a
• /
• pp.355-360
• /
• 2002

ElectroSlag Strip Overlaying (ESSO) process has been around since 1970. ESSO process had limited acceptance due to a few problems associated with the use of this process in its very early stage. Limited knowledge and, most significantly, poor quality of the equipment and welding flux gave the ESSO process a bad name. However, this process is well accepted today and used in North America, Europe and Japan. The ESSO process provides low dilution overlays at high deposition rates, excellent and consistent deposit chemistry with excellent surface quality, and virtually no defects. Capitan has taken this process one step further through extensive research and development of the process itself as well as the equipment. The improvement brought to the process warranted the issuance in May 2000 of an US patent. This study demonstrates the feasibility of this process with immediate positive production results. The main achievements of this work are as follows: $\textbullet$ Development of six various strip-flux combinations on three different base materials: carbon steel, $\frac{1}{4}$ Cr/.5 Mo and 2 $\frac{1}{4}$ Cr/l Mo, fully tested with: penetrant, ultrasound, bends, hardness, overlay chemistry, corrosion and hydrogen disbonding. $\textbullet$ 12" dia. 90 hot formed elbows from straight pipe electroslag overlayed with "1 layer" and "2 layer" Alloy 625 $\textbullet$ a very unique development of miniaturized overlaying equipment able to perform overlay in pipe with diameters as low as 10" (254 mm). This development has large applications in the field of offshore, petrochemical, refining, pulp and paper and power generation industries. The aftermath of this development was its immediate acceptance by major end users with the completion of four projects of overlayed pipe in the USA and Far East Asia.

• Journal of Welding and Joining
• /
• v.18 no.2
• /
• pp.176-176
• /
• 2000

Recently developed Austenite stainless steel,309L was to overlay on 3Cr-1Mo-V-Ti-B steels, using Electroslag welding process, which wide electrodes were adopted. Transition region in welding interlayer relating to disbonding crack was investigated. Also. the effect of welding condition on the width of transition region and coarsening grains of the austenite were studied.1) With increasing welding speed the width of martensite at transient region was increased, but the amount of delta ferrite in weld metal was reduced, being fine grained.2) The form of martensite at the transition region was occured by reversible transition region, leading to increasing Ms point.3) With increasing welding speed, the grain of austenite formed at the welding interface was finer. With increasing welding current under the same welding speed, the grain size of the austenite was finer. At high current, original grain size of the austenite is coarse, but the austenite has fine grains because the austenite was transformed to martensite during cooling.4) In the case of high welding speed, the width of martensite at the welding interface was increased, but the grain size of austenite at the welding interface was finer. This indicates that the inhibition of disbonding crack may be achieved through dispersening fine carbides in the grain boudary.(Received August 3, 1999)

• Journal of Welding and Joining
• /
• v.18 no.2
• /
• pp.49-56
• /
• 2000

Recently developed Austenite stainless steel, 309L was used to overlay on 3Cr-1Mo-V-Ti-B steels, using Electroslag welding process, which wide electrodes were adopted. Transition region in welding interlayer relating to disbonding crack was investigated. Also, the effect of welding condition on the width of transition region and coarsening grains of the austenite were studied. 1) With increasing welding speed the width of martensite at transient region was increased, but the amount of delta ferrite in weld metal was reduced, being fine grained. 2) The form of martensite at the transition region was occurred by reversible transformation during cooling since the interdiffusion of Cr and Ni from weld metal and Fe and C from base metals at the transition region, causes to lowering the concentration of Cr and Ni at the transition region, leading to increasing Ms point. 3) With increasing welding speed, the grain of austenite formed at the welding interface was finer. With increasing welding current under the same welding speed, the grain size of the austenite was finer. At high current, original grain size of the austenite is coarse, but the austenite has fine grains because the austenite was transformed to martensite during cooling. 4) In the case of high welding speed, the width of martensite at the welding interface was increased, but the grain size of austenite at the welding interface was finer. This indicates that the inhibition of disbonding crack may be achieved through dispersening fine carbides in the gain boundary.