• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.1
• /
• pp.35-44
• /
• 2020

The purpose of this study is to elaborate the request for proposal (RFP) for the localization parts development support project of core parts carried out by the Defense Agency for Technology and Quality. The RFP is the most important document throughout the localization parts project, including project announcement and developer selection, design and test of the development product, final evaluation, and standardization of the project. However, if the RFP is not established at the beginning of the project, there is an increased risk of business failure due to frequent changes by various reasons. In this study, we recognized the necessity of elaboration of RFP and applied the AHP method for quantitative elaboration. Eight requirements of the RFP related to the mechanical/electrical performance of localized development products and three elaboration methods for each requirement were designed in a hierarchical structure, and each weight was calculated by applying the 5-point scale AHP method. The AHP survey was conducted with 20 developers participating in the localization parts project, and the consistency ratio of the AHP survey result was less than 0.1. The elaboration method with the highest value among the calculated weights is classified, and the analysis results and future research directions of the elaboration method are presented.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.8
• /
• pp.1802-1809
• /
• 2009

Abstract The typical distribution systems have the power flow from distribution substations (sources) to customers (load) only as one direction. However, in the case where distributed generations (DG) such as PV system and wind power systems are connected to distribution systems, the DG output variations to distribution systems, so called reverse power flow, may cause the bi-directional power flow. So, the reverse power flow has severe impacts on typical power system, for example power quality problems, protection coordination problems, and so on. Especially, protection devices (sectionalizer) in primary feeder of distribution system interconnected with distributed generations may cause problems of malfunction, and then many customers could have problems like an interruption. So, this paper presents the bi-directional operation algorithm of protection devices to overcome the problems like mal-function. And, also this paper shows the effectiveness of proposed method by using both PSCAD/EMTDC software and test facility of protection devices to simulate the field distribution systems.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.9
• /
• pp.4240-4247
• /
• 2013

This purpose of this study was to investigate the difference of safety practice and safety knowledge according to background variables of mothers and the relationship between practice and knowledge in safety of mothers. The subjects were 143 mothers in Iksan city. A questionnaire was made by the researcher on the basis of relevant materials. The data was analyzed by statistical methods such as frequency, Cronbach's ${\alpha}$, descriptive statistics, t-test, ANOVA, Scheffe and Pearson's correlation. The results are as follow: First, mothers' safety knowledge was higher than average. There were significant differences in emergence care, dangerous material, toy safety and young children' developmental character according to mothers' age. There were significant differences in dangerous situation, young children' developmental character and sum score of safety knowledge according to mothers' educational level. So there were significant differences in electrical fire safety, young children's developmental character according to children's age. Second, mothers typically practiced home safety. There were significant differences bathroom, entrance according to mothers' age. And there were significant differences room, kitchen and sum score of safety practice according to children's age. Third, there is no correlation between mothers' safety knowledge and home safety practice.

• Journal of Veterinary Clinics
• /
• v.24 no.3
• /
• pp.320-324
• /
• 2007

This study was undertaken to assess the antinociceptive effect of Korean bee venom (BV) in mice. Korean BV was collected using BV collector devices in which an electrical impulse is used to stimulate the worker bee (Apis mellifera L.) to sting and release venom. After collection, whole BV was evaporated until dry using the BV collector. Experiments were performed on male ICR mice (weighing $30{\sim}35g$, 6 weeks old). Mice were divided into 4 groups, each comprising 8 mice. BV was diluted and amounts of 6 mg/kg body weight (BW), 0.6 mg/kg BW and 0.06 mg/kg BW were tested. BV was subcutaneously injected to produce an antinociceptive effect and the antinociceptive efficacy was evaluated using a writhing test in mice. Intraperitoneal injection of acetic acid produced a tonic pain behavior, first observed at 3 to 9 min post-injection. This writhing response peaked at 20 min post-acetic acid injection, and then declined until it was undetectable at 60 min post-injection. The time elapse between the administration of acetic acid and the first observed pain behaviors indicated a dose-dependent suppressive effect. These results suggest that Korean BV may be used to achieve an antinociceptive effect for use in medical therapies.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.24 no.4
• /
• pp.325-330
• /
• 2004

Several kinds of low voltage cables have been used in nuclear power plants for the supply of electric power, supervision, and the propagation of control signals. These low voltage tables must be inspected for safe and stable operation of nuclear power plants. In particular, the degradation diagnosis to estimate the integrity of low voltage rabies has recently been emphasized according to the long use of nuclear power plants. In order to evaluate their degradation, the surrounding temperature, hardness of insulation material, elongation at breaking point (EAB), etc. have been used. However, the measurement of temperature or hardness is not useful because of the absence of quantitative criteria; the inspection of a sample requires turning off of the power plant power; and, the electrical inspection method is not sufficiently sensitive from the initial through the middle stage of degradation. In this research, based on the theory that the ultrasonic velocity changes with relation to the degradation of the material, we measured the ultrasonic velocity as low voltage cables were degraded. To this end, an ultrasonic degradation diagnosis device was developed and used to measure the ultrasonic velocity with the clothing on the cable, and it was confirmed that the ultrasonic velocity changes according to the degradation of low voltage cables. The low voltage cables used in nuclear power plants were degraded at an accelerated rate, and EAB was measured in a tensile test conducted after the measurement of ultrasonic velocity. With the increasing degradation degree, the ultrasonic velocity decreased, whose potential as a useful parameter for the quantitative degradation evaluation was thus confirmed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.10
• /
• pp.609-617
• /
• 2016

In general, Personal Navigation Systems (PNSs) can be defined systems to acquire pedestrian positional information. GPS is an example of PNS. However, GPS can only be used where the GPS signal can be received. Pedestrian Dead Reckoning (PDR) can estimate the positional information of pedestrians using Inertial Measurement Unit (IMU). Therefore, PDR can be used for GPS-disabled areas. This paper proposes a PDR scheme considering various movement types over GPS-disabled areas as combat environments. We propose a movement distance estimation scheme and movement direction estimation scheme as pedestrian's various movement types such as walking, running and crawling using IMU. Also, we propose a fusion algorithm between GPS and PDR to mitigate the lack of accuracy of positional information at the entrance to the building. The proposed algorithm has been tested in a real test bed. In the experimental results, the proposed algorithms exhibited an average position error distance of 5.64m and position error rate in goal point of 3.41% as a pedestrian traveled 0.6km.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.6
• /
• pp.703-709
• /
• 2017

Korea Utility Helicopter(KUH) is a project to replace the aging helicopter presently being operated by the military with a domestic helicopter. The auxiliary power unit is a device that supplies emergency power to the system by an alternator installed when the main generator fails and the start motor converts the electrical energy of the battery into mechanical rotational energy to rotate the auxiliary power unit engine. With continuing power and operation, defects of the starting motor were found and improvements were carried out to solve it. In the failure mode analysis, the causes of possible defects were classified into 5 categories. Analysis of the 5 factors revealed that the main cause of defects is mechanical wear, which was found to be related to spring pressure. 250 tests were conducted through the theoretically determined pressure and regression analysis was performed with 4 sampling.The results showed that pressure was related to wear rate. In conclusion, early wear and breakage due to wear can be controlled through spring force and test showed the prediction of wear and the validity of the result were confirmed.

• Journal of agriculture & life science
• /
• v.45 no.5
• /
• pp.17-23
• /
• 2011

Growth characteristics and adaptability of 10 poplar clones planted at a reclaimed tidal flat were evaluated. The contents of $Na^+$, $Ca^{2+}$ and $Mg^{2+}$ were 10.0, 3.4 and 1.5 times higher, respectively than those of control although the electrical conductivity(EC) in the soil at the test plantation was low as much as 0.51 dS/m. The contents of organic matter(OM) and total nitrogen(TN) in the soil were 22.9 and 23.0 times lower than those of control. Average survival rate of 10 poplar clones showed 88% at three years after planting. Clones Eco28(Populus euramericana), Dorskamp(Populus deltoides ${\times}$ P. nigra) and I-476(Populus euramericana) showed the best survival rate of 100%. However, clones 97-19(Populus deltoides(Lux) ${\times}$ P. deltoides(Harvard)) and Suwon (Populus koreana ${\times}$ P. nigra var. italica) were relatively lower than other clones. Average height and DBH of all clones were 4.8 m and 3.6 cm, respectively. Clone Dorskamp showed the greatest height and DBH, 5.9 m and 5.0 cm, respectively. Clones 97-19 and Dorskamp showed the least defoliation by stress and visible damage by insects and diseases, whereas clones Suwon and I-476 were the most sensitive at the reclaimed tidal flat. Clone Dorskamp showed the best adaptability at the reclaimed tidal flat, but clone Suwon showed the worst based on survival rate, growth, and visible damages.

• Journal of the Korean Solar Energy Society
• /
• v.31 no.2
• /
• pp.82-88
• /
• 2011

The artificial increase in the solar intensity incident on solar cells using lenses or mirrors can allow solar cells to generate equivalent power with a lower cost. There are two types of concentration optics for solar energy conversion. One is to use mirrors, and the other is to use Fresnel lenses. The gains that can be achieved with a Fresnel lens or a parabolic mirror are compared. The result showed the gains are comparable and the two configurations were developed competitively. In application areas of Fresnel lenses as solar concentrators, several variations of design were devised and tested. Some PV systems still use commercially available flat Fresnel lenses as concentrators. A convex linear Fresnel lens to improve the concentration ratio and the efficiency is devised and flat linear Fresnel lens in thermal energy collection is utilized. In this study, we designed and optimized flat Fresnel lens and the 'light pipe' to develop 500X concentrated solar PV system. In the process, we compare the transmission efficiencies according to groove types. We performed rigorous ray tracing simulation of the flat Fresnel lenses. The computer aided simulation showed the 'grooves in case' has the better efficiency than that of 'grooves out case'. Based on the ray-trace results we designed and manufactured sample Fresnel lenses. The optical performance were measured and compared with ray-trace results. Finally, the optical efficiency was measured to be above 75%. All the design and manufacturing were performed based on that InGaP/InGaAs/Ge triple junction solar cell is used to convert the photon energy to electrical power. Field test will be made and analyzed in the near future.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.31 no.1 s.49
• /
• pp.35-41
• /
• 2005

We investigated the effects of skin hydration and anti-irritation of exopolysaceharide (GF-glucan) produced from submerged culture of Grifola frondosa. The moisturizing effects and trans-epidermal water loss (TEWL) of GF-glucan in cosmetic products (O/W emulsion) were clinically studied. GF-glucan showed good skin hydration effects when compared with sodium hyaluronate which is a commonly using moisturizer. The skin protective effects of GF-glucan against sodium lauryl sulfate (SLS) were also found. Twice a day application of the CF-glucan to skin reduced local inflammation remarkably. Irritant reactions were assessed by various aspects of skin function, erythema (skin color reflectance), hydration (electrical capacitance) and TEWL. In the human skin test, 5-day treatment of the GF-glucan was found to reduce SLS-induced skin erythema and Improve bier regeneration. Taken all together, GF-glucan should be a very useful cosmetic ingredient, as a moisturizer, and a protecting agent for various skin irritations.