• Journal of Electrical Engineering and Technology
• /
• v.12 no.2
• /
• pp.726-737
• /
• 2017

The use of energy storage systems (ESSs) has become a feasible solution to solve the wind power intermittency issue. However, the use of ESSs increases the system cost significantly. In this paper, an optimal power flow control scheme to minimize the ESS capacity is proposed by using the zero-phase delay low-pass filter which can eliminate the phase delay between the dispatch power and the wind power. In addition, the filter time constant is optimized at the beginning of each dispatching interval to ensure the fluctuation mitigation requirement imposed by the grid code with a minimal ESS capacity. And also, a short-term power dispatch control algorithm is developed suitable for the proposed power dispatch based on the zero-phase delay low-pass filter with the predetermined ESS capacity. In order to verify the effectiveness of the proposed power management approach, case studies are carried out by using a 3-MW wind turbine with real wind speed data measured on Jeju Island.

• Journal of electromagnetic engineering and science
• /
• v.14 no.4
• /
• pp.387-392
• /
• 2014

In this paper, a size-reduced Wilkinson balun with wide harmonic-suppressed band is presented. An accurate analysis of the parallel coupled line with an open stub (PCL-OS) is carried out. The PCL-OS structure shows excellent low pass filter and harmonic-suppression characteristics, which is useful for designing a low pass filter unit cell (LUC) with a reduced size. The designed Wilkinson balun at a 2.45 GHz center frequency not only shows an excellent harmonic suppression including the 5th harmonics up to 14 GHz over 15 dB, but it also has an area reduced to 48% of the conventional one.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.53 no.8
• /
• pp.432-437
• /
• 2004

Since the characteristic frequency is decreased in proportion to the fault distance, the characteristic frequency component may be insufficiently eliminated by a low-pass filter on a long transmission line. In order to set a standard for the cut-off frequency of the low-pass filter, this paper proposes a method for obtaining the characteristic frequencies due to line faults. The application results of the proposed method are presented for line to ground (LG) faults and line to line (LL) faults on a 345 kV 200 km overhead transmission line. The EMTP is used to generate fault signals under different fault locations and fault inception angles. By comparison between the characteristic frequencies obtained from the proposed method and the EMTP simulation, it is shown that the proposed method accurately obtains the characteristic frequency.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.4
• /
• pp.281-287
• /
• 1998

$BiNbO_4$ ceramics doped with 0.07wt% $V_2O_5$ and 0.03wt% CuO (BNC3V7) were sucessfully sintered at $900^{\circ}C$ through the firing process with Ag electrode. The BNC3V7 shows typically Dielectric constant of 44.3, Thermal Coefficient of resonance Frequency(TCF) of 2 ppm/$^{\circ} and $Qxf_o$ value of 22,000 GHz. The laminated chip Low Pass Filter (LPF) is very sensitive to chip processing parameters, was confirmed by the computer simulation as a function of Q(Quality factors), filter size, capacitor layer thickness, inductor pattern widths. The multilayer type LPF was fabricated by screen-printing with Ag electrode after tape casting and then compared with the simulated characteristics. The results show that characterization of band pass width was similar to that of designed ones.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.66 no.4
• /
• pp.200-205
• /
• 2017

In this paper, we propose a technique to determine the normal and arc of an alternating current using a mixed filter composed of an average filter and a band-pass filter and a frequency analysis. The proposed method uses the moving average filter of the FIR filter structure for noise removal and the band-pass filter of the IIR filter structure for detecting only specific frequency components after normalizing the measured current signal based on the maximum value. After performing Fast Fourier Transform (FFT) using the band-pass filtered signal, the total energy is calculated using the magnitude component of the frequency, and the arc is detected using the magnitude of the calculated energy. In order to show the validity of the proposed method, we experimented with various data and found that arc and steady state can be easily discriminated by calculating spectral energy. Therefore, it is considered that the proposed method can be applied to arc diagnosis of low voltage electric wire.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.8
• /
• pp.1464-1469
• /
• 2008

A CMOS Gm-C filter with variable cutoff frequency applicable for using in the direct conversion receiver is designed. The designed filter comprises the CMOS differential transconductors, and the gm of the transconductor is controlled by the bias voltage. This configuration can compensate variant of the cutoff frequency which could be generated by external noises, and also be used in multiband receiver. As a results of HSPICE simulation, the control range of the cutoff frequency is $1.5MHz{\sim}3.5MHz$ and the gain control range is $-2.8dB{\sim}2.6dB$. The layout of the designed 5th-order Elliptic low-pass filter is performed to fabricate a chip using $2.5V-0.25{\mu}m$ CMOS processing parameter.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.10
• /
• pp.27-33
• /
• 2016

This paper proposes a Low Noise Amplifier (LNA) with chopper stabilization technique with a sample-hold circuit. Chopper stabilization technique is effective in terms of reducing low frequency offset and flicker noise. Conventional chopper amplifier has a disadvantage in area because of using Low Pass Filter (LPF) for remove chopping spike. The proposed chopper amplifier employed sample and hold technique to decrease chopping spike instead of LPF that improves 36% in voltage damping and 11% in area.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.4
• /
• pp.1589-1596
• /
• 2015

A novel control method of a three-phase PWM inverter with LC filter is proposed. The transfer function of LC filter is the same as that of 2nd order low pass filter(2nd LPF) which has a zero damping ratio. A simple method of implementing 2nd LPF with damping ratio is to add resistor to inductor or capacitor of LC filter. In an industrial application, it is not practical to adopt damping resistor because it results in losses being proportional to square of current flowing through resistor. Instead of using damping resistors, the proposed active damping control(ADC) utilizes all pass filter(APF) and considers inherent processing delay of digital controller. The overall transfer function of the proposed method is the same as a 2nd LPF and its damping ratio is also controllable via control variables. Detailed design and implementation of controller is also presented. Experiments are conducted with a 7.5kVA induction motor drive system controlled by PWM converter and inverter. Test waveforms are also presented to verify the proposed LC filter control algorithm.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.61 no.7
• /
• pp.998-1000
• /
• 2012

By cascading RHTL (Right-Handed Transmission Line) and LHTL (Left-Handed Transmission Line), we fabricated a BPF (Band Pass Filter) in which the phase propagation at the pass band center frequency is fixed as we want. We utilized a positive phase propagation of a RHTL which is a form of LPF (Low Pass Filter) and negative phase propagation of LHTL which is a form of HPF (High Pass Filter). Therefore, if RHTL and LHTL are cascaded, a BPF can be constructed and the phase propagation inside the passband is decided by the number of RHTLs and LHTLs. In this paper, we provide a detailed theory related to it and proved the theory with an actual experiment. In the experiment, we fabricated two BPFs with similar passband. One with $90^{\circ}$ phase shift and the other with $-90^{\circ}$ phase shift at the center of passband. The result of simulation and actual experiment agrees well. This proves the suggested theory is correct and feasible.

• ETRI Journal
• /
• v.28 no.3
• /
• pp.401-404
• /
• 2006

A new log-domain first-order multifunction filter is proposed in this letter. The proposed filter is systematically derived using the state-space synthesis procedure from a corresponding block diagram. It provides low-pass (LP), high-pass (HP), and all-pass (AP) responses simultaneously for a single input signal. The filter circuit has a very simple structure since it uses only bipolar junction transistors (BJTs) and a grounded capacitor. It can be electronically tuned by changing an external current. The filter has a greater bandwidth due to its inherent current-mode and log-domain operations. PSPICE simulations are given to confirm the theoretical analysis.