• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.16 no.2
• /
• pp.113-120
• /
• 2002

This paper describes characteristics of transient voltage waveforms caused by human electrostatic discharges(ESDs). For purpose of achieving the statistics on the meaningful amplitude and initial slope for transient ESD voltage waveforms, transient voltages due to human ESDs in various conditions were observed. A voltage measuring system with a wide bandwidth from DC to 400[MHz] was employed. ESD voltage waveforms are approximately the same as ESD current waveforms. Also the simulated results, which are calculated by the reposed equivalent circuit, are closely similar to the measured voltage waveforms. ESD voltage waveforms are strongly dependent on the approach speed and material of intruder, a fast approach causes ESD voltage waveform with a steep rise time than for a slow approach. The voltage waveforms from dialect finger ESDs have a relatively long rise time of 10∼30[ns], but their peaks are low. On the other side ESD voltage waveforms causer by screwdriver with insulating handle have a steep slope with a very short, less than 1[ns] rise time, but their initial spikes are extremely high The obtained results in this work would be applied to solve ESD problems for low voltage and small current electronic devices.

• Journal of Electrical Engineering and Technology
• /
• v.10 no.2
• /
• pp.529-538
• /
• 2015

Due to the high efficiency and compact mechanical structure, direct drive variable speed generators are used for power conversion in wind turbines. The wind energy conversion system (WECS) considered in this paper consists of a permanent magnet synchronous generator (PMSG), uncontrolled rectifier, dc-dc boost converter controlled with maximum power point tracking (MPPT) and adaptive hysteresis controlled voltage source inverter (VSI). For high utilization of the converter's power capability and stabilizing voltage and power flow, constant DC-link voltage is essential. Step and search MPPT algorithm which senses the rectified voltage ($V_{DC}$) alone and controls the same is used to effectively maximize the output power. The adaptive hysteresis band current control is characterized by fast dynamic response and constant switching frequency. With MPPT and adaptive hysteresis band current control in VSI, the DC link voltage is maintained constant under variable wind speeds and transient grid currents respectively.

• Journal of Electrical Engineering and Technology
• /
• v.3 no.1
• /
• pp.1-7
• /
• 2008

Superconducting Magnetic Energy Storage (SMES) can inject or absorb real and reactive power to or from a power system at a very fast rate on a repetitive basis. These characteristics make the application of SMES ideal for transmission grid control and stability enhancement. The purpose of this paper is to introduce the SMES model and scheme to control the active and reactive power through the power electronic device. Furthermore, an optimal priority scheme is proposed for the combination of active and reactive power control to be able to stabilize power transient swings.

• Proceedings of the KIEE Conference
• /
• 2000.11a
• /
• pp.174-176
• /
• 2000

In this paper, a high speed distance relay, using a digital signal processor(DSP) is presented. The idea of the protective algorithm is based on the least square method using minimum data window to minimize the relay operating time. A new disign concept for a low-pass filter is proposed. This analog low pass filter has minimum transient response time. The main processor of the relay is TMS320C31. According to a series of real time tests, the proposed protective relay shows reliable and fast operating characteristics.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.498-501
• /
• 1998

This paper deals with the design and evaluation of the robust controller for a synchronous generator excitation system to improve the steady state and transient stability. The nonlinear characteristics of the system is treated as model uncertainties, and then the robust control techniques are introduced into the power system stability design to take into account these uncertainties at the controller design stage. The performance of the designed controller is examined by extensive non-linear time domain simulation. It is shown that the performance of the robust controller is superior to that of the conventional PI controller.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1196-1198
• /
• 2000

In this paper, a new approach for digital feedback control of PWM inverter is proposed, in which an output DB(Dead-Beat) control is achieved combined with a simple disturbance observer. The deadbeat controller, which is constructed multiple loop control scheme for PWM inverter, is used for fast transient response. The disturbance observer can make the disturbances be cancelled by adding feedforward compensating loop in controller. The simulation result show the proposed control scheme can achieved good voltage regulation against large load variations.

• Proceedings of the KIEE Conference
• /
• 1995.07b
• /
• pp.791-794
• /
• 1995

This paper introduces a new approach to adaptive control using a combination of direct, indirect and variable structrure method. A new variable structrue input is derived to counteract the effects of disturbances. Direct input is used to have fast response and indirect input improves the transient behavior of the system. Computer simulation results illustrate the very satisfactory performance of the proposed algorithm.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.1
• /
• pp.133-139
• /
• 2013

Convex combination of two adaptive filters is an efficient method to improve adaptive filter performances. In this paper, a subband convex combination method of two adaptive filters for fast convergence rate in the transient state and low steady state error is presented. The cost function of mixing parameter for a subband convex combination is defined, and from this, the coefficient update equation is derived. Steady state analysis is used to prove the stability of the subband convex combination. Some simulation examples in system identification scenario show the validity of the subband convex combination schemes.

• Journal of Electrical Engineering and Technology
• /
• v.2 no.2
• /
• pp.263-266
• /
• 2007

We report a nickel optical MEMS switch, being able to rotate through a large angle and to accommodate multiple channels. The proposed optical switch consists of a thin nickel mirror and two torsion springs supporting the mirror. The torsion springs are designed using a finite element method (FEM) such that plastic deformation of the thin nickel is avoided during the large torsion actuation. For switching speed improvement, transient vibration of the released mirror is suppressed by optimizing the mirror design and a fast switching response of $200\;{\mu}s\;(pull-down)/300\;{\mu}s\;(pull-up)$ is demonstrated.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.10 s.352
• /
• pp.118-125
• /
• 2006

A new error amplifier is presented for fast transient response of DC-DC converters. The amplifier has low quiescent current to achieve high power conversion efficiency, but it can supply sufficient current during large signal operation. Two comparators detect large-signal variations, and turn on extra current supplier if necessary. The amount of extra current is well controlled, so that the system stability can be guaranteed in various operating conditions. The simulation results show that the new error amplifier achieves significant improvement in transient response than the conventional one.