• Journal of Electrical Engineering and Technology
• /
• 제10권3호
• /
• pp.777-785
• /
• 2015

In agricultural systems, significant amount of energy is consumed during irrigation periods. Therefore operating irrigation systems with electrical energy produced by solar energy is very important. It is be possible to operate irrigation systems which have small-pump power like drip-irrigation with electrical energy produced by solar energy. Electrical energy produced by photovoltaic panels can vary from the estimated value due to environmental factors. Consequently analysis of a real system's performance is important. Thus, more correct projections can be made for the systems which will be designed. In this study, induction motor-pump mechanism for drip-irrigation system is operated with photovoltaic generator. Solar energy capacity of the established system is evaluated by measurements in irrigation periods. By means of simulations, power values produced by system and gained from the actual system are compared. Additionally the performance of induction motor is analyzed with the help of the driver system that increases the efficiency and controls the motor. As regards of results, design values of the drip-irrigation systems fed with solar energy in Southeastern Anatolian Regions of Turkey are obtained. Performance results of induction motor controlled with driver are also provided.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1989년도 하계종합학술대회 논문집
• /
• pp.75-78
• /
• 1989

In this paper, A last time delay damper is presented for HB ( HyBrid ) step motor, which has large oscillation characteristics.The design objective is to develop a cost-effective and good-performance damper that would be applyed to HB step motor / driver system without the addition of transducer that would add a weight, size and cost to the system. The Back EMF signal which is recovered from current and voltage signal is used for the measuring the rotor position. It would be possible to get more accurate delay time for the motor driver system. It is proved that the maximum overshoot can be reduced to 13% at stopping through experiment.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제53권9호
• /
• pp.615-621
• /
• 2004

This paper describes the design of a 2-phase stepping motor driver using CPLD. The driver IC such as L297, which is mostly used has some difficulties in PWM current control because of the switching noise of power MOSFETs. The switching noise causes current ripple and acoustic noise. To reduce the switching noise, we designed a digital filter using VHDL. Also we designed constant current method for 1-2 phase(half step) excitation to reduce the torque ripple. Experimental results show the effectiveness of the proposed method. It is enabling further enhancements of stepping motor drive technology broadening the range of applications for the stepping motors.

• 전기학회논문지
• /
• 제65권6호
• /
• pp.1089-1094
• /
• 2016

In order to establish the robust controller design technique of series wound motor driver system. This paper proposes a method of Bang-Bang controller using a series wound motor driver system under improperly variable load. A Bang-Bang controller structure is simpler than the structure of PID plus Bang-Bang controller. This paper shows that a general 8 bits microprocessor is used efficiently implementing such an algorithm. The calculation time of software is extremely small when compared with conventional PID plus Bang-Bang controller. Both nonlinear operating characteristics of digital switching elements and describing function methods are used for the analysis and synthesis. Real time implementation of Bang-Bang controller is achieved. Concept design strategy of the control and PWM waveform generation algorithms are presented in the paper.

• 전기학회논문지
• /
• 제65권5호
• /
• pp.868-872
• /
• 2016

This paper presents the design of a BLDC motor driver applicable to various valve control systems using smart devices. BLDC motors are relatively small in size and have better performance than other motors. They help in reducing maintenance cost, installation costs and power consumption in plant facilities. The proposed driver is specially designed for BLDC motors using Smart Communication Platform. It adds smart features in the valve control system using BLDC motors such as multi-management, control, networking and monitoring in real time with the help of smart devices.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2003년도 ICCAS
• /
• pp.1867-1870
• /
• 2003

The analysis and simulation are the method to study the behavior, response, and specification of the driver device. This paper proposes brushless DC drive which using the vector control technique. The encoder is used detect the rotor position and decode to Three-phase step signal. The step signal is modulated with triangle signal and change to the pulse width modulation (PWM) signal. The PWM signal is used for control the input power of the motor based on the vector control technique. The experimental results of the driver circuit and motor response performed under the following condition: as the motor was started, change the load torque, and vary the supply voltage. The experimental performs with a dynamometer and the test results are compared to the simulation method is the same result.

• 전기학회논문지
• /
• 제59권4호
• /
• pp.733-739
• /
• 2010

We developed to have an automatic transferring function of a two-motors-driven electrical scooter for women or seniors to use conveniently it since it has been previously to operate it in manual only. The function would be implemented by using master and slave micro-control units(MCU) in the system with the given input and output signals. The simulation and test of the system results show that the transition conditions of either higher accelerating speed and/or higher torque are demonstrated at the worst conditions, which means that the transition points might be set either at the 70% of accelerating speed or from the 100% of load torque. The developed equipment is very useful and has good performance in the real test and would be used for top brand and might be applicable to any other types of green cars.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.188-190
• /
• 2005

In this study, a smart motor control and monitoring system is developed with an embedded board where Intel PXA255B CPU is mounted. Linux is ported into the embedded board as RTOS(Real Time Operating System), and the environment which communicate with a motor driver through serial protocol and is capable of controlling and monitoring the motor in real time is built in the system. A user friendly GUI is developed for the convenient operation of the system. Also, the environment which is able to control and monitor the motor driver remotely is built in the system using TCP/IP protocol.

• Journal of Electrical Engineering and Technology
• /
• 제12권5호
• /
• pp.1851-1863
• /
• 2017

Interior permanent magnet synchronous motor (IPMSM) is most commonly used in the automotive industry as a traction motor for electric vehicle (EV). In electric vehicle, the torque output rapidly changes according to the operation of the accelerator and the braking of the driver. The transient torques are thus generated very frequently in accordance with the variable speed control of the driver. Therefore, in this paper, a method for improving the torque response in the transient states of IPMSM is proposed. In order to complement the disadvantages of the conventional PI current controller in the field oriented control (FOC), the finite-state model predictive current control and 2D-LUT is applied to improve the torque response at the torque transient period. Simulation and experiment results are given to verify the reliability of the proposed method.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 F
• /
• pp.2126-2128
• /
• 1997

In order to establish the robust current controller design technique of series wound motor driver system. This paper proposes a method of compensated Bang-Bang current control using a series wound motor driver system under improperly variable load. Real time implementation of compensated Bang-Bang current controller achieved. Concept design strategy of the control and PWM waveform generation algorithms are presented in the paper.