• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.11B no.2
• /
• pp.9-14
• /
• 2001

Because salient pole rotor type single phase SRM(Switched Reluctance Motor) has a simple structure and can be use both radial and axial direction magnetic flux at the same time, its output power per unit volume is high. Therefore, the shaft length can be minimized when compared with same output motors. However, salient pole rotor is hard to design due to its complex magnetic circuit. In this paper, salient pole rotor type single phase SRM with minimized shaft length is designed and selected the most suitable dimension of rotor, stator, pole arc and salient pole.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.457-460
• /
• 1999

The effects of electrical positive stress on n-channel LDD and offset structured poly-Si TFT\`s have been systematically investigated in order to analyze the transfer curve\`s shift mechanism. It has been found that the LDD and offset regions behave as a series resistance that reduce the electric field near drain. Hot carrier effects are reduced because of these results. After electrical stress transfer curve’s shift and variation of the off-current are dependent upon the offset length rather than offset region’s doping concentration. Variation of the subthreshold slope is dependent upon offset region’s doping concentration as well as offset length.

• Proceedings of the KIEE Conference
• /
• 1995.07a
• /
• pp.134-136
• /
• 1995

A superconducting parallel bifilar winding shows the phenomenon which is known as 'fast quench'. We analyzed the temperature characteristics on the winding by computer simulation, and confirmed theses by experiment. The temperature of the quenched point rose gradually as the source voltage was increased. The temperature changed radically as first, but had a gentle slope after a few milliseconds. As the source voltage was large, the initial quenched length also increased. The points in this quenched length showed almost the same temperature. but the points where initial quench had not occurred showed radical temperature gradient. We could observe that the temperature of the whole wire increased simultaneously as the fast quench occurred on the superconducting parallel bifilar winding, because a number of quenched points in that wire appeared at the same time.

• Journal of Energy Engineering
• /
• v.25 no.1
• /
• pp.86-91
• /
• 2016

Convenient design guideline for Waveguide-below-cutoff (WBC) array is proposed to obtain the minimum waveguide length for electromagnetic pulse (EMP) shielding. The analysis includes circular, rectangular, and hexagonal WBC, determine the total length of the waveguide. When the unit side of rectangular WBC and the diagonal line of hexagonal WBC are given as 30 mm, the length of hexagonal WBC is 5 mm shorter than rectangular case with shielding effectiveness (SE) 80 dB. The length difference is deepened with SE of 100 dB, which shows approximately 30 mm shorter length for hexagonal case than others. In addition, hexagonal WBC requires much shorter length than circular WBC. In conclusion, hexagonal case is the most effective with respect to flow velocity and pressure loss for equivalent SE.

• Journal of the Optical Society of Korea
• /
• v.16 no.1
• /
• pp.22-28
• /
• 2012

We report a focal-length tunable liquid lens based on thermopneumatically driven fluidic pressure. The fluidic pressure is generated by deformation of an elastomeric diaphragm induced by thermopneumaticity from a laterally integrated microheater sealed within an air chamber. The pressure is transmitted by a confined liquid to a lens diaphragm through an internal fluid channel. The liquid filling under the lens diaphragm functions as a liquid lens for dynamic focusing with properties depending on the curvature of the deformed diaphragm. The diaphragm area of the air chamber is designed five times larger than that of the lens cavity to yield high focal-length tunability by amplified deflection of the lens diaphragm. With our method, we achieved excellent focal-length tunability from infinity (without an input current) to 4 mm (with an input current of 12 mA) with a lens aperture diameter of 2 mm.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.6
• /
• pp.762-766
• /
• 2013

Interest in Wireless Power Transmission (WPT) technology has been increasing worldwide recently. This trend is proved by commercialized products such as electric toothbrush, wireless razor, and wireless charger for mobile phone battery. Studies for enhancing the applicability of the technology have been continuously conducted. Currently the WPT technology is based on the technologies using microwave, inductively coupling, and magnetic resonance. In the meantime, development of the microwave-based WPT faces difficulty due to health hazards involved in the technology, and application of the WPT technology using inductively coupling is restricted by area due to the problem of transmission length. In comparison, the WPT technology using magnetic resonance draws attention in terms of efficiency and transmission length. In this study, the sending coil based on the WPT technology using magnetic resonance system was replaced with an HTS coil to enhance transmission efficiency. Since the HTS coil has a zero resistance, power transmission loss can be minimized. At the same time, size of the current density could be increased to 100 times or more than typical coils. In addition, through impedance matching of LC device, maximal resonance properties were induced and consequently, frequency selection quality characteristics or Q was enhanced. As a result, the WPT type using the HTS coil showed a longer transmission length and better transmission efficiency compared with the WPT type using typical coils.

• Journal of Communications and Networks
• /
• v.18 no.3
• /
• pp.502-512
• /
• 2016

The wireless carrier sense multiple access with collision detection (WCSMA/CD) and carrier sense multiple access with collision resolution (CSMA/CR) protocols are considered representative distributed collision detection protocols for fully connected dense wireless local area networks. These protocols identify collisions through additional short-sensing within a collision detection (CD) period after the start of data transmission. In this study, we analyze their throughput numerically and show that the throughput has a trade-off that accords with the length of the CD period. Consequently, we obtain the optimal length of the CD period that maximizes the throughput as a closed-form solution. Analysis and simulation results show that the throughput of distributed collision detection protocols is considerably improved when the optimal CD period is allocated according to the number of stations and the length of the transmitted packet.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.10
• /
• pp.506-510
• /
• 2002

In this paper, we study on the mutual characteristics between transmitting efficiency of pulse energy and wall plug consumed power of non-thermal Plasma for removing environmental pollutive gas of coal plant. To obtain high pulse energy of our system, we used MPC(magnetic pulse compressor) of power switch and tested their characteristics by adjusting electrode length of reactor and charging voltage in capacitor. As a result, we obtained consumed power of wall plug and a compressed pulse of voltage 110kV, rising time 500ns. Impedance of load on increasing electrode length was decreased, but electrical efficiency was increased. These results indicate we can control critical voltage of pulse corona and electrical efficiency of economic cost in power plant.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.10a
• /
• pp.319-322
• /
• 2008

This paper introduces experimental investigates of an accident pattern for the distributing XLPE cable terminations considering PL law environment. The influence of defects such as thickness and length decrease of XLPE, the impurity on XLPE and the gap between stress-con of housing and semi-conductor on insulating properties of the termination have been studied. The thickness and length decrease of XLPE decrease ac breakdown strengths. Dielectric breakdown traces of XLPE that is damaged by knife displayed other shape. The gap of between housing and semiconductor deteriorates dielectric strength of XLPE seriously.

• Journal of Electrical Engineering and Technology
• /
• v.4 no.3
• /
• pp.401-404
• /
• 2009

A simple analytical expression for a current gain of IGBT is derived in terms of the device parameters as well as a gate length dependent parameter, which allows for the determination of the current components of the device as a function of its gate length. The analytical results are compared with those from simulation results. A good agreement is found.