• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.8
• /
• pp.632-636
• /
• 2009

The local oxidation using an atomic force microscopy (AFM) is useful for Si-based fabrication of nanoscale structures and devices. SiC is a wide band-gap material that has advantages such as high-power, high-temperature and high-frequency in applications, and among several SiC polytypes, 4H-SiC is the most attractive polytype due to the high electron mobility. However, the AFM local oxidation of 4H-SiC for fabrication is still difficult, mainly due to the physical hardness and chemical inactivity of SiC. In this paper, we investigated the local oxidation of 4H-SiC surface using an AFM. We fabricated oxide patterns using a contact mode AFM with a Pt/Ir-coated Si tip (N-type, 0.01-0.025 ${\Omega}cm$) at room temperature, and the relative humidity ranged from 40 to 50 %. The height of the fabricated oxide pattern (1-3 nm) on SiC is similar to that of typically obtained on Si ($10^{15}^{\sim}10^{17}$ $cm^{-3}$). We perform the 2-D simulation to further analyze the electric field between the tip and the surface. We demonstrated that a specific electric field (4 ${\times}$ $10^7\;V/m$) and a doping concentration ($^{\sim}10^{17}$ $cm^{-3}$) is sufficient to switch on/off the growth of the local oxide on SiC.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.589-590
• /
• 2011

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.149-150
• /
• 2006

We describe a novel method of scanning probe nanofabrication using a AFM(atomic force microscopy) tip with assistance of Femtosecond laser pulses to enhance fabrication capability. Illumination of the AFM tip with ultra-short light pulses induces a strong electric field between the tip and the metal surface, which allows removing metal atoms from the surface by means of field evaporation. Quantum simulation reveals that the field evaporation is triggered even en air when the induced electric field reaches the level of a few volts per angstrom, which is low enough to avoid unwanted thermal damages on most metal surfaces. For experimental validation, a Ti: sapphire Femtosecond pulse laser with 10 fs pulse duration at 800 nm center wavelength was used with a tip coated with gold to fabricate nanostructures on a thin film gold surface. Experimental results demonstrate that fine structures with critical dimensions less than ${\sim}10nm$ can be successfully made with precise control of the repetition rate of Femtosecond laser pulses.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.31 no.1 s.256
• /
• pp.139-144
• /
• 2007

This paper presents development of carbon nanotube (CNT) tip modified by focused ion beam (FIB) and experimental results in non-contact mode of atomic force microscopy (AFM) using fabricated tip. We used an electric field which causes dielectrophoresis, to align and deposit CNTs on a conventional silicon tip. The morphology of the fabricated CNT tip was then modified into a desired shape using focused ion beam. We measured anodic aluminum oxide sample and trench structure to estimate the performance of FIB-modified tip and compared with those of conventional Si tip. We demonstrate that FIB modified tip in non contact mode had superior characteristics than conventional tip in the respects of wear, image resolution and sidewall measurement.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.08a
• /
• pp.98.2-98.2
• /
• 2013

Electrochemical phenomena underpin a broad spectrum of energy, chemical, and information technologies such as resistive memories and secondary batteries. The optimization of functionalities in these devices requires understanding electrochemical mechanisms on the nanoscale. Even though the nanoscale electrochemical phenomena have been studied by electron microscopies, these methods are limited for analyzing dynamic electrochemical behavior and there is still lack of information on the nanoscale electrochemical mechanisms. The alternative way can be an atomic force microscopy (AFM) because AFM allows nanoscale measurements and, furthermore, electrochemical reaction can be controlled by an application of electric field through AFM tip. Here, I will summarize recent studies to probe nanoscale electrochemical reaction in battery applications by AFM. In particular, we have recently developed electromechanical based AFM techniques for exploring reversible and irreversible electrochemical phenomena on the nanoscale. The present work suggests new strategies to explore fundamental electrochemical mechanisms using the AFM approach and eventually will provide a powerful paradigm for probing spatially resolved electrochemical information for energy applications.

• Korean Journal of Materials Research
• /
• v.14 no.7
• /
• pp.505-510
• /
• 2004

The glass-ceramic based on LAS($Li_{2}O-Al_{2}O_3-SiO_{2}$) system was observed using SEM(Scanning Electric Microscopy) and AFM(Atomic Force Microscopy) and it was expected to get a correlation between the crystal size and the surface roughness through the result. At heat treatment conditions (the nucleation: $740\~800^{\circ}C$, the crystal growth: $900\~1150^{\circ}C$), the crystal size was increased from 72 to 450 nm so that the mean of surface roughness was also risen from 0.8 to 6.3 nm. Based on the results, the surface roughness of glass-ceramic is controlled by the factors, crystal size, crystallines, and the condition of heat treatment.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.501-504
• /
• 2004

This paper describes the fabrication method for atomic force microscopy(AFM) tip with multi-walled carbon nanotube(MWNT). For making a carbon nanotube (CNT) modified tips, AC electric field which cause the dielectrophoresis was used for alignment and deposition of CNTs in this research. By dropping the MWNT solution and applying an electric field between an AFM tip and an electrode, MWNTs which were dispersed into a diluted solution were directly assembled onto the apex of the AFM tips due to the attraction by the dielectrophoretic force. In this case, we investigate the effect of the angle between a tip axis and an electrode. Experimental setup were presented, and then CNT attached AFM tips are successfully shown in this paper.

• Korean Journal of Materials Research
• /
• v.28 no.11
• /
• pp.680-684
• /
• 2018

We investigate the effect of light intensity and wavelength of a solar cell device using photoconductive atomic force microscopy(PC-AFM). A $POCl_3$ diffusion doping process is used to produce a p-n junction solar cell device based on a polySi wafer, and the electrical properties of prepared solar cells are measured using a solar cell simulator system. The measured open circuit voltage($V_{oc}$) is 0.59 V and the short circuit current($I_{sc}$) is 48.5 mA. Moreover, the values of the fill factors and efficiencies of the devices are 0.7 and approximately 13.6 %, respectively. In addition, PC-AFM, a recent notable method for nano-scale characterization of photovoltaic elements, is used for direct measurements of photoelectric characteristics in limited areas instead of large areas. The effects of changes in the intensity and wavelength of light shining on the element on the photoelectric characteristics are observed. Results obtained through PC-AFM are compared with the electric/optical characteristics data obtained through a solar simulator. The voltage($V_{PC-AFM}$) at which the current is 0 A in the I-V characteristic curves increases sharply up to $18W/m^2$, peaking and slowly falling as light intensity increases. Here, $V_{PC-AFM}$ at $18W/m^2$ is 0.29 V, which corresponds to 59 % of the average $V_{oc}$ value, as measured with the solar simulator. Furthermore, while the light wavelength increases from 300 nm to 1,100 nm, the external quantum efficiency(EQE) and results from PC-AFM show similar trends at the macro scale but reveal different results in several sections, indicating the need for detailed analysis and improvement in the future.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.04a
• /
• pp.500-503
• /
• 2004

본 연구에서는 금속 원자를 단열 팽창시켜 클러스터를 만들고, 생성된 클러스터를 이온화시킨 후 집속렌즈 및 electric quadrupole을 이용하여 기판으로 증착 하였다. 집속렌즈의 설계에서는 단일 초점 방식의 렌즈보다 성능을 높이기 위하여 이중 초점과 핀홀을 써서 집속 효과 및 효율을 높였다. 렌즈의 설계는 일반적으로 하전입자의 에너지 손실 없이 집속할수 있는 Einzel 렌즈를 기본으로 하였으며, SIMION software 를 사용하여 시뮬레이션 하였다. 시뮬레이션 후 실제 렌즈계 및 정전압원을 제작하여 금(Au)의 클러스터를 생성하여 렌즈계를 통과한 후 실제 기판위로 증착이 되는 것을 AFM(Atomic force microscopy)과 XPS(X-ray photoemission spectroscopy)를 이용해 조사하여 렌즈계가 실제로 동작함을 확인하였다.

• Proceedings of the KIEE Conference
• /
• 2005.11a
• /
• pp.136-138
• /
• 2005

Merocyanine dye (MD) has been extensively investigated due to its marked potential application to photo-electric devices. We fabricated the number of layers to control its optical characteristics using the Langmuir-Blodgett (LB) method. We evaluated the morphology and optical characteristics of MD LB films using Atomic Force Microscopy (AFM) and UV spectroscopy, PL spectroscopy. As a result, we obtained the quantitative morphology and optical characteristics of LB films from controlling the deposided layers.