• Proceedings of the KSR Conference
• /
• 2004.10a
• /
• pp.1259-1265
• /
• 2004

Electro-magnetic clutch which is affected by elements of electric, magnetic and mechanical friction is important that it has a characteristic changes by environmental impact. Expecially, it is equipped in railroad sideway which is bleak external environment. Therefore, this paper investigated affections by temperature changes, which can make out through physical characteristics such as friction torque, minimum slipping torque, rated slipping torque of electro-magnetic dutch.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.11a
• /
• pp.796-799
• /
• 2002

BSCCO thin films are fabricated via a co-deposition process at an ultra-low growth rate using ion beam sputtering. The sticking coefficient of Bi element exhibits a characteristic temperature dependence. This temperature dependence of the sticking coefficient was explained consistently on the basis of the evaporation and sublimation processes of Bi$_2$O$_3$.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.3
• /
• pp.58-65
• /
• 2013

In this paper, we propose that a model based design for an electric motor cycle system using ASM (Automotive Simulation Models). Before prototyping a realistic electric motorcycle, a reliable simulation program is required to test the capacities of the power sources and optimize the parameters of an electric motorcycle. Because ASM is based on Simulink, we can design the drivetrain and powertrain of the vehicle model systems easily. To verify the electric motorcycle system analysis of design parameters such as max power, capacity, state of charge and slope angle is carried out by the simulation and experimental method. The predicted results by the development model were in good agreement with the experimentally obtained results. Therefore, the proposed electric motorcycle model can effectively reduce the expenses during the designing of an electric motorcycle system.

• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.87-88
• /
• 2008

현재 전국적으로 많은 곳에 SPS(고장파급방지장치)가 설치되어 운영중에 있으며 대부분은 345kV이상 대단위 전원단지 인근에 설치되어 있으나 강원지역의 경우는 154kV 계통에 다수가 설치되어 운전중에 있다. 강원지역은 지역적 특성으로 인해 장거리 송전선로가 많으며 전원단이 원거리에 위치하여 고장시 전압불안정에 의한 계통붕괴의 위험성이 타 지역보다 높다. 특히 하계에 비해 난방부하 및 심야전력의 영향으로 최대부하가 대폭 증가하는 동계의 경우 이러한 특성이 더욱 두드러지는데 2007년 동계피크시 부하실적 및 역률을 기준으로 부하특성 및 부하역율 변동에 따른 계통영향을 분석하여 기 설치 운영중인 SPS 적용의 타당성 및 유지여부에 대한 판단 및 SPS 적용 개선(안)을 제시하였다.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.7
• /
• pp.1558-1563
• /
• 2013

In this paper, we analyze the radio propagation path loss characteristics for the vertical electric dipole radiation over the perfect electric conductor(PEC) ground plane. Most research have been performed about the electromagnetic analysis of vertical electric dipole in free space for time domain or frequency domain. But this paper present the radio propagation path loss over PEC ground plane in time domain under the assumption of the vertical electric dipole as a base station. From the simulated results, the ground plane effect can change the location of near field from transmitting antenna and the transient responses at mobile are calculated. The results of this paper can be applied to surface radar or signal processing applications.

• Proceedings of the KIEE Conference
• /
• 1999.11d
• /
• pp.1099-1101
• /
• 1999

PJB(Prefabricated Joint Box) is consisted of three major components ; an epoxy unit, a stress relief cone and a spring unit. The insulation structure of PJB is maintained by the interfacial pressure, and the dielectric performance at the interface depends on the interfacial pressure which is regarded as the most important factor for preventing breakdown failure. This experiment was performed to investigate breakdown voltage characteristic and partial discharge patterns under the controlled pressure conditions at the simulated interface. Finally, this paper presents the optimal pressure conditions at the interface by analyasing the PD patterns.

• Journal of the Korean Ceramic Society
• /
• v.32 no.3
• /
• pp.289-294
• /
• 1995

As the results of the study on the effects of mixing time for raw materials to the electric and magnetic properties of Mg-ferrite, the fraction of spinel phase after calcination and the geometry density of sintered Mg-ferrite increased from 30% to 100% and from 2.5g/cc to 4.25g/cc respectively due to mixing-homobenity of raw materials. The AC resistivity of grains decreased and lattice parameter, saturation magnetization increased due to the increase in Fe+2 of sintered body. conclusively the characteristic of powder after calcination had strong influence on the microstructure, electric, and magnetic properties in Mg-ferrite sintered body.

• Journal of the Korean Society of Safety
• /
• v.7 no.4
• /
• pp.105-114
• /
• 1992

This paper presents an study on the knowledge based system for diagnosing the fire causes using the Fuzzy Possibility Measure( FPM ) about the electric-fire ignition. The Ignition values needed for causes diagnosis is computed as FPM for electric-fire ignition based on the internal scale technique that assigns numerically the characteristic difference of facts to the-tin-ear scale. For the convinience of inference, ignition sources are classified into seven types : short, ground fault, leakge of electricity, overcurrent, cord junction overheating, bad Insulation and spark. The system for causes diagnosis of electric-fire is composed of Knowledge Acquisition System, Inference Engine and Man-Machine Interface, The diagnosis system is wrritten in an artificial intelligence langusge “PROLOG” which uses depth-first search and backward chaining schemes in reasoning process.

• Proceedings of the KIEE Conference
• /
• 2004.10a
• /
• pp.215-217
• /
• 2004

This paper shows the analysis of the inductive power transfer system in conjunction with series resonant converter operating variable high frequency. Of particular interest is the sensitivity of the complete system to variations in operational frequency and parameters. In inductive power transfer system, electrical power is transferred from a primary winding in the form of a coil or track, to one or more isolated pick-up coils that may relative to the primary. The ability to transmit power without contact enables high reliability and easy maintenance that allows inductive power transfer system to be implemented in hostile environments. This technology has found application in many fields such as electric vehicles, PRT(Personal Rapid Transit) etc. The coupling between the primary and secondary is then presented to include the effects of parameter and operational frequency variation.

• Proceedings of the KIPE Conference
• /
• 2001.12a
• /
• pp.71-75
• /
• 2001

Currently there are very limited amounts of resources and serious amounts pollution. Wind power generation system have an advantage of unlimited and unpolluted amount of energy resource. In this paper, for the application of these characteristic and for the generation to be achieved regard of districts and geographical features the energy continuously. The operation characteristics of system were analyzed through experiments for a trial product.