• 한국전기전자재료학회논문지
• /
• 제13권1호
• /
• pp.85-93
• /
• 2000

In this paper, the predischarge propagation processes of SF\ulcorner gas stressed by impulse voltages under nonuniform electric field perturbed by a needle protrusion are described. The statistical and formative time-lags and the time interval between leader pulses were investigated on the basis of the predischarge current measured in the gas pressure range of 0.1~0.5 MPa. The predischarge current is closely related to the waveform, amplitude and polarity of applied votages, the gas pressure and the gap geometry. Both the positive and negative predischarge processes in nonuniform electric field develop in a regime of stepwise leader propagation leading to electrical breakdown. The mean of the time interval between leader pulses gives about a factor of 10 higher for the negative than for the positive leader current puls-es. According as the gas pressure increases, the statistical time-lag was almost unchangeable, but the formative time-lag was gradually decreased.

• Journal of Plant Biology
• /
• 제29권1호
• /
• pp.1-10
• /
• 1986

Intra- and inter-specific protoplast fusion of tobacco (Nicotiana tabacum cv. Virginia 115) and pea (Pisum sativum cv. Sparkle) were carried out in highly inhomogeneous alternating electric fields. Under the electric field of alternating current (AC, sine wave), 600 V/cm and 800 kHz for tobacco protoplast, and 600 V/cm and 700 kHz for pea protoplasts, the protoplasts were aggregated in pearl chains. Intra-specific protoplast fusions were most effectively induced within the aggregates of tobacco and pea, respectively, by the additional application of a single high field pulse of direct current (DC, square wave) at 1 kV/cm for 50 $mutextrm{s}$. Inter-specific fusions between protoplasts of the two plants were most effectively induced in the electric field of 600 V/cm and 700 kHz, and square wave pulse at 1 kV/cm for 50 $mutextrm{s}$. The duration of the pulse over the electrical breakdown voltages was simulated from 1 to 100 $mutextrm{s}$ in both tobacco and pea protoplast. The yield of the electrofusion products was significantly high (above 60%), compared with that (20%) of the standard fusion method by polyethylene glycol (PEG) 4,000, and the viability of electrofused protoplasts was above 70%, but that of PEG-fused protoplasts 8~16%, when determined by Evan's blue staining method.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제49권12호
• /
• pp.673-678
• /
• 2000

The dielectric barrier discharge(DBD) is a common method to create a nonthermal plasma in which electrical energy is used to create electrons with a high average kinetic energy. The unique aspect of dielectric barrier discharges is the large array of short lifetime(10ns) silent discharges created over the surface of the dielectric. A silent discharge is generated when the applied voltage exceeds the breakdown voltage of the carrier gas creating a conduction path between the applied electrode and grounded electrode. As charge accumulates on the dielectric, the electric field is reduced below the breakdown field of the carrier gas and the silent discharge self terminates preventing the DBD cell from producing a thermal arc. In fact, the most significant application of dielectric barrier discharges is to generate ozone for contaminated water treatment. Therefore, experiments were perfomed at 1∼2[bar] pressure using a coaxial geometry single dielectric barrier discharge for ozone concentrations and energy densities. The main result show that the concentration and efficiency of ozone are influenced by gas nature, gas quantity, gas pressure, supplied voltage and frequency.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 C
• /
• pp.1808-1810
• /
• 2004

This paper describes the discharge characteristics of liquid $SF_6$ (-41$[^{\circ}]$, 1.7[atm]) and $LN_2$ for plane to plane, needle to plane, plane to needle and sphere to plane electrode with gap variations from 1[mm] to 12[mm]. From this result, the breakdown voltage was increased with increasing gap length. Especially, the formation of bubbles by evaporation was observed in spite of non-applying voltage source. A corona is created of the applying voltage from the bubbles on the electrodes applied voltage. We consider it equal mechanism of corona as void exists in solid insulator. The results of liquid $SF_6$ and $LN_2$ discharge characteristics were caused by bubble formed evaporation and applied electric field voltage. Corona was happened to weak bubble and was proceed to new bubble breakdown.

• 전기학회논문지
• /
• 제62권11호
• /
• pp.1571-1577
• /
• 2013

Electrical tree structure is one of the most important influencing factors for electrical treeing characteristics in polymers. In this paper, we focused on the structure characteristics of electrical treeing in epoxy resins (original) insulation under different high-frequency voltages (60, 500, 1000Hz). Effects of voltage frequency on the ac electrical treeing phenomena in an epoxy resins were carried out in needle-plate electrode arrangement. To measure the treeing initiation and propagation, and the breakdown rate, constant AC of 10 kV with three different voltage frequencies (60, 500 and 1,000 Hz) was applied to the specimen in needle-plate electrode specimen at $30^{\circ}C$ of insulating oil bath. At 60 Hz, the treeing initiation time was 360 min and the propagation rate was $6.85{\times}10^{-4}mm/min$, and the morphology was dense branch type. As the voltage frequency increased, the treeing initiation time decreased and the propagation rate increased. At 1,000 Hz, the treeing initiation time was 0 min and the propagation rate was $7.81{\times}10^{-2}mm/min$, and the morphology was dense bush type.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제14권5호
• /
• pp.673-681
• /
• 2014

In this paper, a novel low specific on-resistance SOI LDMOS Device with P+P-top layer in the drift region is proposed and investigated using a two dimensional device simulator, MEDICI. The structure is characterized by a heavily-doped $P^+$ region which is connected to the P-top layer in the drift region. The $P^+$ region can modulates the surface electric field profile, increases the drift doping concentration and reduces the sensitivity of the breakdown voltage on the geometry parameters. Compared to the conventional D-RESURF device, a 25.8% decrease in specific on-resistance and a 48.2% increase in figure of merit can be obtained in the novel device. Furthermore, the novel $P^+P$-top device also present cost efficiency due to the fact that the $P^+$ region can be fabricated together with the P-type body contact region without any additional mask.

• 전기학회논문지
• /
• 제67권1호
• /
• pp.142-147
• /
• 2018

Private electrical facilities are judged whether it is suitable for the insulation aging condition of their incoming underground cables using DC leakage current test method. In the case where the service point of utility is the secondary side of cut out switch installed in the electric pole, there is a problem that it is difficult to separate the lightning arresters(LA) because of their high position of the pole. Therefore, the field test voltage is applied at value lower than DC 30 kV, which are stated in the inspection guideline. However, this test could reduced the insulation performance of the LA by accelerating the electrical stress of the metal oxide varistor element in the pre-breakdown region. In this study, we analyzed the relationship between the DC test voltage and the leakage current using the non-destructive DC high voltage equipment with leakage current measurement function. The results show that the leakage current increases sharply above the specified test voltage. As a consequence, it could be contributed to improve insulation aging inspection method by selecting the possible test area on the VI characteristic curve of the pre-breakdown area of the LA.

• 한국세라믹학회지
• /
• 제29권1호
• /
• pp.29-34
• /
• 1992

Phase transition, dielectric properties, and leakage current characteristics of Ta2O5 thin film fabricated by sol-gel process with tantalum penta-n-butoxide were studied as a function of annealing temperature in O2 atmoshpere. Although Ta2O5 thin film annealed at temperatures below 700$^{\circ}C$ for 1 hr was amorphous, it was crystallized to ${\beta}$-Ta2O5 of orthorhombic phase by annealing at temperatures higher than 750$^{\circ}C$. With increasing annealing temperature from 500$^{\circ}C$ to 900$^{\circ}C$, dielectric constant of sol-gel processed Ta2O5 thin film was changed from 17.6 to 15.3 due to the increase of SiO2 thickness at Ta2O5/Si interface. For Ta2O5 thin film annealed at 500$^{\circ}C$ to 800$^{\circ}C$ for 1 hr in O2 atmosphere, leakage current was remarkably reduced and breakdown strength was increased with higher annealing temperature. For Ta2O5 film annealed at 800$^{\circ}C$, breakdown did not occur even at electric field strength of 30${\times}$105V/cm and leakage current was maintained lower than 10-8A/$\textrm{cm}^2$.

• 한국전기전자재료학회논문지
• /
• 제14권7호
• /
• pp.546-550
• /
• 2001

A new Lateral Trench Insulated Gate Bipolar Transistor(LTIGBT) with p$^{+}$ diverter was proposed to improve the characteristics of the conventional LTIGBT. The forward blocking voltage of the proposed LTIGBT with p$^{+}$ diverter was about 140V. That of the conventional LTIGBT of the same size was 105V. Because the p$^{+}$ diverter region of the proposed device was enclosed trench oxide layer, he electric field moved toward trench-oxide layer, and punch through breakdown of LTIGBT with p$^{+}$ diverter was occurred, lately. Therefore, the p$^{+}$ diverter of the proposed LTIGBT didn't relate to breakdown voltage in a different way the conventional LTIGBT. The Latch-up current densities of the conventional LTIGBT and proposed LTIGBT were 540A/$\textrm{cm}^2$, and 1453A/$\textrm{cm}^2$, respectively. The enhanced latch-up capability of the proposed LTIGBT was obtained through holes in the current directly reaching the cathode via the p$^{+}$ divert region and p$^{+}$ cathode layer beneath n$^{+}$ cathode layer./ cathode layer.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 춘계학술대회 논문집
• /
• pp.1168-1173
• /
• 2007

The Seoul Subway is one of the most heavily used Subway System in the world. It provides reliable transportation services, conveys nearly 4 million Passengers across 117 subway stations with a length of 134.9 Km. Over the years the safety for the Subway has been a major concern, trains going off the track, equipment failure, careless operation, Signal failure are increasing day by day. In a Recent Public opinion 40% said the causes to above facts are Vehicle breakdown because of Operators, Old rail defect, Quality of material. 20% of the opinion said the obstacles were because of Operation, crew carelessness, negligence in signal operation. In case of any accident the crew members cannot resolve the issue on site (Aid insufficiency), because of lack of knowledge and carelessness. The main obstacles for Subway are vehicle breakdown, Electric equipment failure, Signal Equipment failure, and Crew carelessness. This paper aims to provide major problems which are needed to be solved as quickly as possible for citizen's safety for a comfortable subway system making a comfortable ride and providing better service gradually.