• 한국통신학회논문지
• /
• 제21권6호
• /
• pp.1596-1603
• /
• 1996

A single body type of fiber-optic current and voltae sensor using a rare earth doped YIG and a bismuth silicon oxide single crystsl is proposed, which is used for simultaneous measurement of the AC electric current and AC electric voltage over the trasmission lines. Experimental results showed that the fiber-optic current sensor has the maximum 7.5% error within the current range of 0A to 400A, and the fiber-optic voltage sensor has the maximum 0.87% error within the current range of 0V to 400V. The output waveforms of proposed fiber-optic sensor system has a good agreement with output waveforms of conductor current and voltage. Experimental results proved that the output of fiber-optic current sensor is not affected by the electric voltage applied to the fiber-optic voltage sensor, and also, that the output of fiber-optic voltage sensor is not affected by the electric current applied to the fiber-optic current sensor.

• 전기학회논문지
• /
• 제62권6호
• /
• pp.750-755
• /
• 2013

In-wheel motor system gets the driving force from direct-driven motor in the wheel of electric vehicle. It is known as good system for vehicles, from an efficiency, packaging, handling and safety. This paper describes motor and inverter technologies, system configuration and control algorithms for in-wheel type electric vehicle. It is necessary to control on an interrelation perspective because this system drives two motors at same time. In system design, IPMSM(Interior Permanent Magnet Synchronous Motor) including a wide operating range and high-speed rpm is used and flux weakening control is performed in constant power range. Under the torque command from the host controller, auto control box, inverter's output torque is calculated with using torque estimation technique and applied to actual vehicle driving system. It is verified that the configuration and the algorithm are suitable for the in-wheel motor system.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2002년도 하계학술대회 논문집 C
• /
• pp.1649-1651
• /
• 2002

Ultra-wide bandwidth (UWB) detection method has been widely used as a front end detection scheme for the ultra-high frequency (UHF) partial discharge (PD) monitoring systems. A broad-band video detector module was developed and characterized for the UHF UWB PD detection systems. The useable bandwidth of the module is more than 2 GHz and it is optimized for 50-ohm systems. The detection sensitivity and dynamic range of the module were characterized by using a known ns-width RF pulses of GHz range. The dynamic range is more than 6-decades and the module can detect pulsed RF signals down to 1 nW. The detector module can eliminate expensive equipment such as high speed oscilloscopes and radio frequency (RF) spectrum analyzers. Therefore, it enables one to use slow speed data acquisition systems for the PD monitoring at the UHF range. The detector module was used to detect real PDs of about <3 pC. The module converts the UWB PD signals into a low-bandwidth video signal with a high signal-to-noise ratio.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권3호
• /
• pp.313-319
• /
• 2002

Since the oil crisis in 1970, a great deal of effort has been made to develop automatic electric load sharing systems as a part of the efforts to save energy. A large scale electric generating system composes more than two generators whose characteristics may be different. When such a system is operated individually or in parallel, the lagrange multiplier's method has difficulty in achieving optimal load distribution because generators usually have the limitations of the operating range with inequality constraints. Therefore, a suitable operating mode of generators has to be decided according to the selection of the generators to meet electric power requirements at the minimum cost. In this study, a method which solves the optimal electric load distribution problem using the dynamic programming technique is proposed. This study also shows that the dynamic programming method has an advantage in dealing with the optimal load distribution problem under the limitations of the operating range with inequality constraints including generator operation mode. In this study, generator operating cost curve of second order equation by shop trial test results of diesel generators are used. The results indicate that the proposed method can be applied to the ship's electric generating system.

• 대한기계학회논문집A
• /
• 제32권10호
• /
• pp.856-865
• /
• 2008

Damage mechanisms in bending piezoelectric actuators under electric fatigue loading are addressed in this work with the aid of an acoustic emission (AE) technique. Electric cyclic fatigue tests have been performed up to $10^7$ cycles on the fabricated bending piezoelectric actuators. An applied electric loading range is from -6 kV/cm to +6 kV/cm, which is below the coercive field strength of the PZT ceramic. To confirm the fatigue damage onset and its pathway, the source location and distributions of the AE behavior in terms of count rate and amplitude are analyzed over the fatigue range. It is concluded that electric cyclic loading leads to fatigue damages such as transgranular damages and intergranular cracking in the surface of the PZT ceramic layer, and intergranular cracking even develops into the PZ inner layer, thereby degrading the displacement performance. However, this fatigue damage and cracking do not cause the final failure of the bending piezoelectric actuator loaded up to $10^7$ cycles. Investigations of the AE behavior and the linear AE source location reveal that the onset time of the fatigue damage varies considerably depending on the existence of a glass-epoxy protecting layer.

• KEPCO Journal on Electric Power and Energy
• /
• 제8권1호
• /
• pp.31-36
• /
• 2022

This paper presents the measuring process of dynamic properties of offshore wind power foundation and provides consideration of each step. This Guideline enables to maintain consistent measuring procedure and therefore increase the reliability of test results. Small scaled suction bucket foundation was fabricated to represent the commercial support structure installation mechanism and two cases(free-free, free-fixed) of dynamic tests were performed at workshop. From the tests, the importance of dynamic properties of connection part between suction bucket and tower was figured out. More over, types and configuration of measuring devices are recommended which can help find the natural frequency of wind turbine foundation correctly. In field test, it was found that the natural frequency of suction bucket foundation was increased linearly with the penetration depth due to the confining effect of ambient soil. Meanwhile, it was not easy to get an enough excitation force with normal impact hammer because the N.F of suction bucket model was in the lower range of 0 Hz ~ 5 Hz. Therefore, new excitation method which has enough force and can excite lower frequency range was devised. This study will help develop safety check procedure of suction bucket foundation in field at each installation stage using the N.F measurement.

• International journal of advanced smart convergence
• /
• 제8권1호
• /
• pp.58-64
• /
• 2019

In recent years, small mobile devices called personal mobility or smart mobility have attracted attention. Personal mobility refers to electric-driven personal transportation that can travel at close range and medium distance, including small electric vehicles, electric bicycles, electric motorcycles and electric scooters. Most of the electric scooters used in Korea are mainly imported from China. This is due to the fact that the price competitiveness of major components of electric scooters is owned in China. At this point, the domestic research direction is preferable for the composition and design of the electric scooter body rather than cost reduction for the components. In this study, we propose a new model of portable folding structure that is easy to use for electric scooters, which are personal vehicles using electric energy. We also made a prototype for practical use.

• 대한기계학회논문집A
• /
• 제38권1호
• /
• pp.37-44
• /
• 2014

본 연구에서는 전기이륜차의 1회충전주행거리를 알아보기 위해 도로 주행시험과 차대동력계(Chassis Dynamometer) 주행시험을 하였다. 도로주행시험은 대전시(Daejeon Metropolitan City)의 도로 중 대표적인 3가지 루트에서 주행시험을 하였다. 차대동력계를 이용한 CVS-40모드 주행시험의 경우 도로 부하조건을 다양하게 설정하여 CVS-40 모드주행을 실시하였다. 본 연구를 통하여 도로에서의 전기이륜차의 1회 충전주행거리(Per-Charge Range Testing)를 확인하고, 차대동력계 도로부하 설정방법에 따른 주행거리 및 에너지소비효율을 측정하였다. 이를 통해 실도로 주행시험과 차대동력계 주행시험을 비교하여, 차대동력계 실험에서도 전기이륜차 1회충전주행거리시험이 실도로에서의 주행조건과 근접한 결과를 갖는 도로부하 설정에 대해 연구하였다.

• 한국시뮬레이션학회:학술대회논문집
• /
• 한국시뮬레이션학회 1999년도 추계학술대회 논문집
• /
• pp.181-185
• /
• 1999

In this paper, we apply AHP method to select long range technology alternative for KEPCO. The input data was gathered by the questionnaire surveys answered by experts. The effectiveness and validity of the method were tested by comparing the results with those of the current selection procedure. We show that the proposed method can outperform the current method and can applied to the real decision making process of the electric power company.

• 산업공학
• /
• 제13권2호
• /
• pp.166-170
• /
• 2000

In this paper, we apply AHP method to select long range technology alternatives for KEPCO. The input data was gathered by the questionnaire surveys answered by experts. The effectiveness and validity of the method were tested by comparing the results with those of the current selection procedure. We show that the proposed method can outperform the current method and can be applied to the real decision making process of the electric power company.