• Journal of Power Electronics
• /
• v.17 no.2
• /
• pp.334-345
• /
• 2017

In order to meet the increasing needs of the hybrid energy source system for electric vehicles, which demand bidirectional power flow capability with a wide-voltage-conversion range, a bidirectional three-level DC-DC converter and some control strategies for hybrid energy source electric vehicles are proposed. The proposed topology is synthesized from Buck and Boost three-level DC-DC topologies with a high voltage-gain and non-extreme duty cycles, and the bidirectional operation principle is analyzed. In addition, the inductor current ripple can be effectively reduced within the permitted duty cycle range by the coordinated control between the current fluctuation reduction and the non-extreme duty cycles. Furthermore, benefitting from duty cycle disturbance control, series-connected capacitor voltages can also be well balanced, even with the discrepant rise and fall time of power switches and the somewhat unequal capacitances of series-connected capacitors. Finally, experiment results of the bidirectional operations are given to verify the validity and feasibility of the proposed converter and control strategies. It is shown to be suitable for hybrid energy source electric vehicles.

• Journal of Radiation Industry
• /
• v.2 no.3
• /
• pp.141-148
• /
• 2008

Beta rays emitted from tritium in titanium tritide film were simulated with cathode rays of a scanning electron microscope to investigate the effect of beta rays from tritium on semiconductor devices. The cathode ray currents, which vary with the change of applied energy and beam spot size, were measured with Faraday cup. The current from the semiconductor device irradiated with cathode rays at various conditions was measured. The cathode ray current increased with the increase of spot size to a maximum then decreased when the spot sized increased further. The magnitude of current produced in the semiconductor device is proportional to the magnitude of cathode ray current. The magnitude of cathode ray current at each energy level was matched to the intensity of beta ray to simulate the tritium beta ray spectrum. Then the semiconductor characteristics were analyzed with I-V curves.

• Progress in Superconductivity
• /
• v.10 no.1
• /
• pp.60-67
• /
• 2008

We present domestic efforts for superconducting fault current limiter (SFCL) application in the Korea Electric Power Corporation (KEPCO) grid and pending points at issue. KEPCO's decision to upgrade the 154 kV/22.9 kV main transformer from 60 MVA to 100 MVA cast a problem of high fault current in the 22.9 kV distribution lines. The grid planners supported adopting an SFCL to control the fault current. This environment friendly to SFCL application must be highly dependent upon the successful development of SFCL having specifications that domestic utility required. The required conditions are (1) small size of not greater than twice of 22.9 kV gas insulated switch-gear (GIS), (2) sustainability of current limitation without the line breaking by circuit breakers (CB) for maximum 1.5 seconds. Also, optionally, recommended is (3) the reclosing capability. Conventional resistive SFCLs do not meet (1) $\sim$ (3) all together. A hybrid SFCL is an excellent solution to meet the conditions. The hybrid SFCL consists of HTS SFCL components for fault detection and line commutation, a fast switch (FS) to break the primary path, and a limiter. This characteristic structure not only enables excellent current limiting performances and the reclosing capability, but also allows drastic reduction of HTS volume and small size of the cryostat, resulting in economic feasibility and compactness of the equipment. External current limiter also enables long term limitation since it is far less sensitive to heat generation than HTS. Semi-active operation is another advantage of the hybrid structure. We will discuss more pending points at issues such as maintenance-free long term operation, small size to accommodate the in-house substation, passive and active control, back-up plans, diagnosis, and so on.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.12
• /
• pp.2682-2688
• /
• 2012

In this paper, we design and implement a electric current controller for ignition coil to measure the amount of current and to supply the additional current under vehicle driving conditions in spark ignition engines. The proposed controller can provide the stable current and prevent the overcurrent by measuring the amperage of primary ignition in real time. Also it enhances the performance of vehicle engine by controling the amount of ignition energy that make power increase and fuel burn more completely. The power and torque of the normal vehicle is evaluated as performance index for the experimental validation of the control module. The experimental results using dynamometer equipment show that after control module-mounted elevates the average of 10% more in both power and torque compared with before module-mounted.

• Journal of The Korean Association For Science Education
• /
• v.12 no.3
• /
• pp.61-76
• /
• 1992

The purpose of this study was to develop the instructional model and teaching material to change the middle school students'conceptions of electric current into the scientific ones and to investigate the effects of the model in actual classrooms. We identified the students' ideas and their misunderstanding about the concept of eIectic current through reviewing the literatures and our in this study. Based on the above results, we developed the instructional model and designed the teaching sequence and prepare the learning materials about the unit of the electric current in middle school Our instructional model was based on 'learning cycle' developed by Lawson, but the new stage called "exploration through qualitative questions" to elicit the students' own conceptions was inserted to it. To investigate the effects or the new teaching model, the pre- and post-test using the POE type were administered to experimental group(52 students) taught with learning cycles and control group(52 students) taught with traditional styles. The results are as follows; 1) The rates of correct. predictions was varying according to the kinds of problems. And the rates of the correct. reasons of their predictions were lower than those of the predictions. 2) The mean scores of the post-test of both groups were significantly higher than those of the pre-test. We could not find statistically significant difference in theme an score between experimental group and control group after implementation of the model. But the experimental group gained higher scores than those of the control group on two problem. Therefore, although we cannot show the prominent effects of our teaching model based on learning cycles, there are some effects of our model on changing the middle school students' conceptions of electric current.

• Proceedings of the KSR Conference
• /
• 2011.05a
• /
• pp.634-643
• /
• 2011

The neutral section was installed in order to prevent conflict with different phase angle source in electric railway catenary system. The speed of electric train reduced due to coasting operation by notch off when it passed the neutral section. And, the catenary wire was damaged and the accident might be happened because of the arc generation when the electric train passed the neutral section with notch off condition. The inrush current of main transformer installed tiling train is analyzed during the operation of MCB(main circuit break) passing through the neutral section. The instantaneous waveform of load current were analyzed in case of powering and regenerative braking. Inrush current waveform with run of AC railway train showed that inrush current waveform and harmonics, the inrush current generated from main transformer in train has bad effects on power quality problem. In order to reduce these inrush currents, the MCB is connected when the phase angle of voltage is 90 degree. This paper is to measure inrush current and harmonics in main transformer of high speed train in neutral section of electric railway. This measurement report is used to control minimum inrush current in algorithm and power phase angle.

• Proceedings of the KIPE Conference
• /
• 2011.07a
• /
• pp.429-430
• /
• 2011

This paper presents a simple and cost-effective stand-alone rapid battery charging system of 30kW for electric vehicles. The proposed system mainly consists of active front-end rectifier of neutral point clamped 3-level type and non-isolated bi-directional dc-dc converter of multi-phase interleaved half-bridge topology with coupled inductors. The charging system is designed to operate for both lithium-polymer and lithium-ion batteries. The complete charging sequence is made up of three sub-interval operating modes; pre-charging mode, constant-current mode, and constant-voltage mode. The pre-charging mode employs the staircase shaped current profile to accomplish shorter charging time while maintaining the reliable operation of the battery. The proposed system is able to reach the full-charge state within less than 16min for the battery capacity of 8kWh by supplying the charging current of 67A. The optimal discharging algorithm for Vehicle to the Grid (V2G) operation has been adopted to maintain the discharging current of 1C. Owing to the simple and compact power conversion scheme, the proposed solution has superior module-friendly mechanical structure which is absolutely required to realize flexible power expansion capability in a very high-current rapid charging system.

• Proceedings of the KIPE Conference
• /
• 1997.07a
• /
• pp.352-356
• /
• 1997

This paper present the design of a novel neural-network (NN) based pulse-width modulation (PWM) techniques for a three-level power converter of electric trains along with nonlinear mapping of essential switching patterns and fault tolerance, which are inherent characteristics of NNs. Considering the importance of safety, power factor and harmonics of electric train power converters, two-level type and three-level type of power converters using NNs are precisely investigated and compared in computer simulation. A computer simulation shows that a new current control scheme provides an improved performance over a fixed-band hysteresis current control in many aspects.

• Journal of the Korean Society of Safety
• /
• v.15 no.2
• /
• pp.63-69
• /
• 2000

The constraint conditions are the stator voltage and the stator current to operate the motor in the flux weakening region. The maximum current is limited by the inverter current rating and the machine thermal rating. Given DC link voltage to control the motor in the flux weakening the maximum voltage is determined by considering PWM strategy, dead time, voltage drop of the inverter switching device, and the margin of the voltage for current forcing. In this paper, the new method to determine the available maximum voltage is derived by the quantitative method and by considering the factors of the voltage drop. The proposed method to determine the maximum voltage is very useful to improve the stability of the motor system and to enlarge the speed operation region in the flux weakening operation. Therefore the utility of the maximum voltage is increased.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.1213-1219
• /
• 2008

The deterioration analysis of electric systems in diesel electric locomotives, which were used for over 30 years, was performed to understand current wear and safety information. The electric systems include electric generation, traction motors, control units, high-voltage cables, and wires. In this investigation, various types of performance testing, such as insulation resistance measurement and degradation tests, were conducted to assess the degree of current deterioration. Moreover, an infrared camera was employed to verify abnormal heating in cables and wires. In this paper, the new techniques for evaluation of deterioration in electric systems have been introduced.