• 대한기계학회논문집
• /
• 제16권4호
• /
• pp.684-695
• /
• 1992

본 연구에서는 3차원 형상의 금형에 의한 박판금속 성형 공정을 에너지법으로 해석함에 있어 스윕곡면(SWeep surface)을 통해 기하학적 형상을 효과적으로 표현하는 방법을 제안하고, 이를 직사각형 격막의 정수압벌징의 해석에 으용하여 이에 의한 결 과를 이미 보고된 자료와 비교함으로써 일반적인 박판 성형공정을 해석하는데 본 이론 의 적용 가능성에 대하여 논의하고자 한다.

• 대한기계학회논문집A
• /
• 제25권4호
• /
• pp.756-763
• /
• 2001

In the process of integrity evaluation for nuclear power plant components, a series of fracture mechanics evaluation on surface cracks in reactor pressure vessel(RPV) must be conducted. These fracture mechanics evaluation are based on stress intensity factor, K. However, under pressurized thermal shock(PTS) conditions, the combination of thermal and mechanical stress by steep temperature gradient and internal pressure causes considerably high tensile stress at the inside of RPV wall. Besides, the internal pressure during the normal operation produces high tensile stress at the RPV wall. As a result, cracks on inner surface of RPVs may experience elastic-plastic behavior which can be explained with J-integral. In such a case, however, J-integral may possibly lose its validity due to constraint effect. In this paper, in order to verify the suitability of J-integral, tow dimensional finite element analyses were applied for various surface cracks. A total of 18 crack geometries were analyzed, and $\Omega$ stresses were obtained by comparing resulting HRR stress distribution with corresponding actual stress distributions. In conclusion, HRR stress fields were found to overestimate the actual crack-tip stress field due to constraint effect.

• 대한기계학회논문집A
• /
• 제24권3호
• /
• pp.777-785
• /
• 2000

The low-cycle fatigue behaviors of cast AI-Si alloy and composite with reinforcement of SIC particles were compared with those of extruded unreinforced matrix alloy and composite in order to investigate the influence of cast and extrusion processes on the cyclic deformation and fatigue life. Generally, both cast and extruded composites including the unreinforced alloy exhibited cyclic hardening behaviour, with more pronounced strain-hardening for the composites with a higher volume fraction of the SiC particles. However, cast composite under a low applied cyclic strain showing no observable plastic strain exhibited cyclic softening behavior due to the cast porosities. The elastic modulus and yield strength of the cast composite were found to be quite comparable to those of the extruded composite, however, the extrusion process considerably improved the ductility and fracture strength of the composite by effectively eliminating the cast porosities. Low-cycle fatigue lives of the cast alloy and composite were shorter than those of the extruded counterparts. Large difference in life between cast and extruded composites was attributed to the higher influence of the cast porosities on the fatigue life of the composite than that of the unreinforced alloy material. A fatigue damage parameter using strain energy density effectively represented the inferior life in the low-cycle regime and superior life in the high-cycle regime for the composite, compared to the unreinforced alloy.

• 비파괴검사학회지
• /
• 제27권1호
• /
• pp.1-7
• /
• 2007

섬유강화 복합재료가 항공기, 우주 구조물, 로봇 팔 등에 널리 사용됨에 따라 복합재료의 신뢰도와 안전성을 향상시키기 위하여 이에 대한 비파괴검사법은 매우 중요한 연구분야로 대두되고 있다. AE법은 복합재의 균열, 섬유 또는 수지재의 파손, 층간분리 등의 발생 및 성장과정에서 발생되는 탄성파로 인한 스트레인 에너지를 검출하는 방법이다. 본 논문에서는 $8{\times}8$ 매트릭스형 피에조 센서를 사용하여 인장시험 하에서 발생되는 AE신호를 측정하고 분석하였다. 이를 위하여 AE신호의 전달거리를 제어할 수 있는 전용회로를 설계하고 제작하였다. 또한 64채널의 AE신호를 획득하기 위하여 발광다이오드를 사용한 광학 저장장치를 구성하였다. 실험결과, $8{\times}8$ 매트릭스형 피에조 센서를 이용하여 복합재료에서 발생되는 AE신호의 발생지점과 전파경로를 효과적으로 검출할 수 있었다.

• Structural Engineering and Mechanics
• /
• 제57권3호
• /
• pp.507-528
• /
• 2016

Reduced beam section (RBS) moment resisting connections are among the most economical and practical rigid steel connections developed in the aftermath of the 1994 Northridge and the 1995 Kobe earthquakes. Although the performance of RBS connection has been widely studied, this connection has not been subject to in the skewed conditions. In this study, the seismic performance of dogbone connection was investigated at different angles. The Commercial ABAQUS software was used to simulate the samples. The numerical results are first compared with experimental results to verify the accuracy. Nonlinear static analysis with von Mises yield criterion materials and the finite elements method were used to analyze the behavior of the samples The selected Hardening Strain of materials at cyclic loading and monotonic loading were kinematics and isotropic respectively The results show that in addition to reverse twisting of columns, change in beam angle relative to the central axis of the column has little impact on hysteresis response of samples. Any increase in the angle, leads to increased non-elastic resistance. As for Weak panel zone, with increase of the angle between the beam and the column, the initial submission will take place at a later time and at a larger rotation angle in the panel zone and this represents reduced amount of perpendicular force exerted on the column flange. In balanced and strong panel zones, with increase in the angle between the beam and the central axis of the column, the reduced beam section (RBS), reaches the failure limit faster and at a lower rotation angle. In connection of skewed beam, balanced panel zone, due to its good performance in disposition of plasticity process away from connection points and high energy absorption, is the best choice for panel zone. The ratio of maximum moment developed on the column was found to be within 0.84 to 1 plastic anchor point, which shows prevention of brittle fracture in connections.

• Structural Engineering and Mechanics
• /
• 제61권3호
• /
• pp.407-417
• /
• 2017

RC shear walls are considered one of the main lateral resisting members in buildings. In recent years, FRP has been widely utilized in order to strengthen and retrofit concrete structures. A number of experimental studies used CFRP sheets as an external bracing system for retrofitting of RC shear walls. It has been found that the common mode of failure is the debonding of the CFRP-concrete adhesive material. In this study, behavior of RC shear wall was investigated with three different micro models. The analysis included 2D model using plane stress element, 3D model using shell element and 3D model using solid element. To allow for the debonding mode of failure, the adhesive layer was modeled using cohesive surface-to-surface interaction model at 3D analysis model and node-to-node interaction method using Cartesian elastic-plastic connector element at 2D analysis model. The FE model results are validated comparing the experimental results in the literature. It is shown that the proposed FE model can predict the modes of failure due to debonding of CFRP and behavior of CFRP strengthened RC shear wall reasonably well. Additionally, using 2D plane stress model, many parameters on the behavior of the cohesive surfaces are investigated such as fracture energy, interfacial shear stress, partial bonding, proposed CFRP anchor location and using different bracing of CFRP strips. Using two anchors near end of each diagonal CFRP strips delay the end debonding and increase the ductility for RC shear walls.

• Earthquakes and Structures
• /
• 제18권5호
• /
• pp.527-542
• /
• 2020

In traditional eccentrically braced steel frames, damages and plastic deformations are limited to the links and the main structure members are required tremendous sizes to ensure elasticity with no damage based on the force-based seismic design method, this limits the practical application of the structure. The high strength steel frames with eccentric braces refer to Q345 (the nominal yield strength is 345 MPa) steel used for links, and Q460 steel utilized for columns and beams in the eccentrically brace steel frames, the application of high strength steels not only brings out better economy and higher strength, but also wider application prospects in seismic fortification zone. Here, the structures with four type eccentric braces are chosen, including K-type, Y-type, D-type and V-type. These four types EBFs have various performances, such as stiffness, bearing capacity, ductility and failure mode. To evaluate the seismic behavior of the high strength steel frames with variable eccentric braces within the similar performance objectives, four types EBFs with 4-storey, 8-storey, 12-storey and 16-storey were designed by performance-based seismic design method. The nonlinear static behavior by pushover analysis and dynamic performance by time history analysis in the SAP2000 software was applied. A total of 11 ground motion records are adopted in the time history analysis. Ground motions representing three seismic hazards: first, elastic behavior in low earthquake hazard level for immediate occupancy, second, inelastic behavior of links in moderate earthquake hazard level for rapid repair, and third, inelastic behavior of the whole structure in very high earthquake hazard level for collapse prevention. The analyses results indicated that all structures have similar failure mode and seismic performance.

• 대한조선학회논문집
• /
• 제39권2호
• /
• pp.69-80
• /
• 2002

선박의 곡외판은 냉간가공과 열간가공(선상가열) 과정을 거쳐 제작된다. 선상가열의 자동화 및 기계화에 대한 연구가 다양하게 수행되어 오고 있다. 특히 가열조건과 잔류 변형 사이의 관계규명은 자동화 및 기계화를 위한 주요 요소로 생각된다. 본 연구는 그러한 관계를 규명하기 위하여 일련의 체계적인 과정을 제시하고 관계식을 제안하였다. 선상가열에 의한 변형은 3차원 열탄소성 변형현상으로 정식화될 수 있으며, 열탄소성 변형현상을 유한요소해석을 이용하여 다양한 가열조건에 대한 수치해석을 수행하였다. 유한요소법의 유용성을 검증하기 위하여 실험을 수행하였고 그 유용성을 확인하였다 변형관계식에 사용된 입력변수는 차원해석을 통하여 선정하였다. 유한요소법을 이용하여 얻어진 결과를 활용하여 선상가열에 의한 변형관계식을 추정하기 위하여 다변수해석과 다차원 보관과정을 예시하였다. 일련의 과정을 통하여 본 연구는 선상가열의 가열조건과 잔류 변형 사이의 관계식을 선정하기 위한 방법을 제안하였다.

• 한국지반신소재학회논문집
• /
• 제10권4호
• /
• pp.29-36
• /
• 2011

본 연구는 포천 화강토의 건조단위중량을 $16.67kN/m^3$, $17.26kN/m^3$, $17.65kN/m^3$으로 각각 변화시켜 등방압축-팽창시험과 구속압력을 달리한 일련의 배수삼축시험을 하였다. 그리고 이 시험자료를 이용하여 회귀분석을 근거로 건조단위중량의 변화에 따른 Lade의 단일항복면 구성모델의 토질매개변수의 변화 특성을 알아보았다. 그 결과 탄성성분, 파괴규준, 경화함수, 소성포텐셜에 관련된 토질매개변수는 상대밀도의 증가에 따라 선형적인 증 감현상을 보이고 있다. 그리고 항복함수에 관련된 토질매개변수 h와 ${\alpha}$는 상대밀도에 따른 변화가 미세하고 파괴규준에 관련한 토질매개변수와 관련성이 매우 높아 ${\eta}_1$에 관한 식으로 대체할 수 있으며, 이 식을 이용한 수치해석 결과 양호하게 예측하고 있는 것을 확인 할 수 있었다.

• 대한기계학회논문집A
• /
• 제27권11호
• /
• pp.1986-1996
• /
• 2003

Methodology based on the elastic-plastic fracture mechanics has been widely accepted in predicting the critical crack length(CCL) of pressure tubes of CANDU nuclear plants. A conservative estimate of CCL is obtained by employing the J-resistance curves measured with the specimens satisfying plane strain condition as suggested in the ASTM standard. Due to limited thickness of the pressure tubes the curved compact tension(CT) specimens taken out from tile pressure tube have been used in obtaining J-resistance curves. The curved CT specimen inevitably introduce slant fatigue crack during precracking. Hence, effect of specimen geometry and slant crack on J-resistance curve should be explored. In this study, the difference of J integral values between the standard CT specimens satisfying plane strain condition and the nonstandard curved CT with limited thickness (4.2mm) is estimated using finite element analysis. The fracture resistance curves of Zr-2.5Nb obtained previously by other authors are critically discussed. Various finite element analysis were conducted such as 2D analysis under plane stress and plane strain conditions and 3D analysis for flat CT, curved CT with straight crack and curved CT with slant crack front. J-integral values were determined by local contour integration near the crack tip, which was considered as accurate J-values. J value was also determined from the load versus load line displacement curve and the J estimation equation in the ASTM standard. Discrepancies between the two values were shown and suggestion was made for obtaining accurate J values from the load line displacement curves obtained by the curved CT specimens.