• 한국강구조학회 논문집
• /
• 제27권4호
• /
• pp.359-370
• /
• 2015

본 연구에서는 AFRP 스트립과 강재사이의 부착거동에 관한 실험적 연구를 수행하였다. 실험적 연구를 통해 AFRP 판과 강판사이의 계면부착거동을 관찰하고, 계면부착응력을 산정하는 것이 본 연구의 목표이다. 실험변수로는 부착길이와 AFRP의 두께를 선택하였으며, 18개의 일면전단시편 제작하여 실험을 수행하였다. 실험결과 부착길이와 AFRP 두께가 증가함에 따라 하중값을 증가하였으며, 부착길이와 AFRP 두께가 증가함에 따라 각각 63%, 86%의 하중값이 증가하였다. 끝으로 강재와 AFRP 사이의 부착응력-슬립관계를 산정하였다. 부착응력-슬립관계는 탄성선형거동을 보이고 있으며, 부착길이와 AFRP 두께는 부착응력과 파괴에너지에 영향을 덜 미치는 것으로 나타났다.

• 대한기계학회논문집A
• /
• 제24권3호
• /
• pp.777-785
• /
• 2000

The low-cycle fatigue behaviors of cast AI-Si alloy and composite with reinforcement of SIC particles were compared with those of extruded unreinforced matrix alloy and composite in order to investigate the influence of cast and extrusion processes on the cyclic deformation and fatigue life. Generally, both cast and extruded composites including the unreinforced alloy exhibited cyclic hardening behaviour, with more pronounced strain-hardening for the composites with a higher volume fraction of the SiC particles. However, cast composite under a low applied cyclic strain showing no observable plastic strain exhibited cyclic softening behavior due to the cast porosities. The elastic modulus and yield strength of the cast composite were found to be quite comparable to those of the extruded composite, however, the extrusion process considerably improved the ductility and fracture strength of the composite by effectively eliminating the cast porosities. Low-cycle fatigue lives of the cast alloy and composite were shorter than those of the extruded counterparts. Large difference in life between cast and extruded composites was attributed to the higher influence of the cast porosities on the fatigue life of the composite than that of the unreinforced alloy material. A fatigue damage parameter using strain energy density effectively represented the inferior life in the low-cycle regime and superior life in the high-cycle regime for the composite, compared to the unreinforced alloy.

• Structural Engineering and Mechanics
• /
• 제57권3호
• /
• pp.507-528
• /
• 2016

Reduced beam section (RBS) moment resisting connections are among the most economical and practical rigid steel connections developed in the aftermath of the 1994 Northridge and the 1995 Kobe earthquakes. Although the performance of RBS connection has been widely studied, this connection has not been subject to in the skewed conditions. In this study, the seismic performance of dogbone connection was investigated at different angles. The Commercial ABAQUS software was used to simulate the samples. The numerical results are first compared with experimental results to verify the accuracy. Nonlinear static analysis with von Mises yield criterion materials and the finite elements method were used to analyze the behavior of the samples The selected Hardening Strain of materials at cyclic loading and monotonic loading were kinematics and isotropic respectively The results show that in addition to reverse twisting of columns, change in beam angle relative to the central axis of the column has little impact on hysteresis response of samples. Any increase in the angle, leads to increased non-elastic resistance. As for Weak panel zone, with increase of the angle between the beam and the column, the initial submission will take place at a later time and at a larger rotation angle in the panel zone and this represents reduced amount of perpendicular force exerted on the column flange. In balanced and strong panel zones, with increase in the angle between the beam and the central axis of the column, the reduced beam section (RBS), reaches the failure limit faster and at a lower rotation angle. In connection of skewed beam, balanced panel zone, due to its good performance in disposition of plasticity process away from connection points and high energy absorption, is the best choice for panel zone. The ratio of maximum moment developed on the column was found to be within 0.84 to 1 plastic anchor point, which shows prevention of brittle fracture in connections.

• Structural Engineering and Mechanics
• /
• 제61권3호
• /
• pp.407-417
• /
• 2017

RC shear walls are considered one of the main lateral resisting members in buildings. In recent years, FRP has been widely utilized in order to strengthen and retrofit concrete structures. A number of experimental studies used CFRP sheets as an external bracing system for retrofitting of RC shear walls. It has been found that the common mode of failure is the debonding of the CFRP-concrete adhesive material. In this study, behavior of RC shear wall was investigated with three different micro models. The analysis included 2D model using plane stress element, 3D model using shell element and 3D model using solid element. To allow for the debonding mode of failure, the adhesive layer was modeled using cohesive surface-to-surface interaction model at 3D analysis model and node-to-node interaction method using Cartesian elastic-plastic connector element at 2D analysis model. The FE model results are validated comparing the experimental results in the literature. It is shown that the proposed FE model can predict the modes of failure due to debonding of CFRP and behavior of CFRP strengthened RC shear wall reasonably well. Additionally, using 2D plane stress model, many parameters on the behavior of the cohesive surfaces are investigated such as fracture energy, interfacial shear stress, partial bonding, proposed CFRP anchor location and using different bracing of CFRP strips. Using two anchors near end of each diagonal CFRP strips delay the end debonding and increase the ductility for RC shear walls.

• 대한기계학회논문집
• /
• 제17권6호
• /
• pp.1351-1360
• /
• 1993

본 연구에서는 수적법(hand lay up : HLU)을 이용하여 단 섬유포(chopped strand mat : CSM)형태의 유리섬유를 불포화 폴리에스테르 수지에 강화시킨 복합 적층 판을 대상으로 해수중에서 굽힘·피로시험을 실시하여 피로균열 성장거동을 관찰하고 파면관찰을 통하여 GERP의 피로특성을 검토하였다.

• 한국재료학회지
• /
• 제20권3호
• /
• pp.125-131
• /
• 2010

In this study, Ti powders were fabricated from Ti scrap by the Hydrogenation-Dehydrogenation (HDH) method. The Ti powders were prepared from the spark plasma sintering (SPS) and their microstructure was investigated. Hydrogenation reactions of Ti scrap occurred at near $450^{\circ}C$ with a sudden increase in the reaction temperature and the decreasing pressure of hydrogen gas during the hydrogenation process in the furnace. The dehydrogenation process was also carried out at $750^{\circ}C$ for 2 hrs in a vacuum of $10^{-4}$ torr. After the HDH process, deoxidation treatment was carried out with the Ca (purity: 99.5%) at $700^{\circ}C$ for 2 hrs in the vacuum system. It was found that the oxidation content of Ti powder that was deoxidized with Ca showed noticeably lower values, compared to the content obtained by the HDH process. In order to fabricate the Ti compacts, Ti powder was sintered under an applied uniaxial punch pressure of 40 MPa in the range of $900-1200^{\circ}C$ for 5 min under a vacuum of $10^{-4}$ torr. The relative density of the compact was 99.5% at $1100^{\circ}C$ and the tensile strength decreased with increasing sintering temperature. After sintering, all of the Ti compacts showed brittle fracture behavior, which occurred in an elastic range with short plastic yielding up to a peak stress. Ti improved the corrosion resistance of the Ti compacts, and the Pd powders were mixed with the HDH Ti powders.

• 소성∙가공
• /
• 제31권6호
• /
• pp.376-383
• /
• 2022

The potential damage region of a WC-Co cemented carbide die is investigated for cold forging process of a wheel-nut by numerical simulation with its chemical composition considered. Numerical simulation is utilized to calculate internal stress, especially for the WC-Co die, during the forging process. Finite element model is established, in which the elasto-plastic properties are applied to the work-piece of bulk steel, and elastic properties are considered for the lower die insert of the WC-Co alloy. This stress analysis enables to distinguish the potential damage regions of the WC-Co die. The regions from calculation are comparatively analyzed along with the crack area observed in the die after repetitive manufacturing. Effect of chemical composition of the WC-Co is also evaluated on characteristics of potential damage region of the die with variance of mechanical properties considered. Derived from Mohr-Coulomb fracture model, furthermore, a new stress index is presented and used for die stress analysis. This index inherently considers hydrostatic pressure and is then capable of deducing wide range of its distribution for representing stress state by modification of its parameter implying pressure sensitivity.

• Nuclear Engineering and Technology
• /
• 제52권12호
• /
• pp.2949-2957
• /
• 2020

Fatigue crack growth model has been developed for dissimilar metal weld joints of a piping component under cyclic loading, where in the crack is located at the center of the weld in the circumferential direction. The fracture parameter, Stress Intensity Factor (SIF) has been computed by using principle of superposition as K_H + K_M. K_H is evaluated by assuming that, the complete specimen is made of the material containing the notch location. In second stage, the stress field ahead of the crack tip, accounting for the strength mismatch, the applied load and geometry has been characterized to evaluate SIF (K_M). For each incremental crack depth, stress field ahead of the crack tip has been quantified by using J-integral (elastic), mismatch ratio, plastic interaction factor and stress parallel to the crack surface. The associated constants for evaluation of K_M have been computed by using the quantified stress field with respect to the distance from the crack tip. Net SIF (K_H + K_M) computed, has been used for the crack growth analysis and remaining life prediction by Paris crack growth model. To validate the model, SIF and remaining life has been predicted for a pipe made up of (i) SA312 Type 304LN austenitic stainless steel and SA508 Gr. 3 Cl. 1. Low alloy carbon steel (ii) welded SA312 Type 304LN austenitic stainless-steel pipe. From the studies, it is observed that the model could predict the remaining life of DMWJ piping components with a maximum difference of 15% compared to experimental observations.

• 한국항공우주학회지
• /
• 제48권5호
• /
• pp.363-372
• /
• 2020

고 변형률 속도에 대한 소재의 동적 압축 물성은 고속 충돌 및 고속 성형 등 동적 환경에서의 유한요소 해석의 신뢰성 향상을 위해 필수적이다. 일반적으로 고 변형률 속도에 대한 소재의 동적 압축 물성은 SHPB(Split Hopkinson Pressure Bar) 장비를 통해 획득 가능하다. 본 연구에서는 최근 무인 항공기에 확대 적용되고 있는 Woven type CFRP(Carbon Fiber Reinforced Plastic) 소재에 대한 충돌 해석에 대응하기 위해 SHPB 장비를 활용하여 해당 소재의 동적 압축 물성을 획득하였다. 또한 Pulse shaper를 활용하여, Elastic-brittle 특성을 지니는 소재에 대한 일정한 변형률 속도 확보 및 실험 데이터에 대한 신뢰도를 향상시켰다. CFRP 소재의 경우 방향 별 기계적 물성이 다른 이방성 소재이므로 두께 방향과 면내 방향 시편을 제작하여 각각 실험을 수행하였다. SHPB 실험 결과 면내 방향 시편의 경우 일정한 변형률 속도 영역에 도달하기 전, 시편의 파단이 발생하여 데이터의 재현성 및 신뢰성 확보에 어려움이 있는 반면, 두께 방향의 시편의 경우 시편 전·후면 응력일치도가 우수하여 데이터 신뢰도가 높으며, 일정한 변형률 속도 영역을 획득할 수 있다. LS-dyna를 활용한 유한요소해석을 통해, 압력봉으로부터 측정되는 데이터는 시편과 압력봉의 변형에 의해 변형률이 과도하게 예측되는 것을 확인하였다.

• 터널과지하공간
• /
• 제17권5호
• /
• pp.411-427
• /
• 2007

타당성 있는 터널의 설계 및 경제적 시공을 위해서는 터널해석의 신뢰성이 확보되어야 한다. 이를 위해서는 암반과 지보재의 상호 작용을 포함하여 시공 전반에 걸친 깊은 이해가 필요하다. 본 논문에서는 파괴 이후에도 지보력을 상실하지 않는 강섬유보강 숏크리트의 거동을 적절히 모델링하는 기법을 소개하였다. 강지보재의 지보 효과를 알아보기 위해 3차원 해석을 수행하였으며, 이를 통하여 새로운 하중분담율이 산정되었다. 소성모멘트한계만을 사용한 경우(PML 모델) 숏크리트에 비정상적으로 발생하던 높은 인장응력을 없앨 수 있었고, 파괴 후의 연성 거동을 모사할 수 있었으나 축력의 영향이 고려되지 못하여 실제 거동과의 괴리를 메우기에는 다소 미흡하였다. 따라서 축력과 모멘트 한계를 동시에 고려할 수 있는 방법이 필요하였는데, FLAC의 내장 모델인 liner 모델을 통하여 이러한 거동이 모사될 수 있었다. Liner 모델에서는 강섬유 보강 숏크리트의 일축압축 강도와 더불어 최대 및 잔류 인장강도도 지정이 가능하다. 이 두 가지 모델을 이용하여 4등급 및 5등급 암반에 굴착되는 2차로 터널에 대하여 해석을 수행하였다. 또한 종래에 사용되던 탄성 beam 모델을 이용한 해석도 병행하여 그 결과를 비교하였다. 탄성 beam 모델을 제외한 두 가지 모델은 탄성 beam 모델에서는 반영될 수 없었던 휨인성을 고려할 수 있었다.