• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1999년도 추계학술대회 논문집
• /
• pp.13-22
• /
• 1999

Both the resonance and ultrasonic techniques are standard methods far characterizing the physical properties of piezoelectric materials. However, we found that each technique can only offer a few reliable measurements while the rest often have errors or impossible to implement because of the sample requirements. This paper show that one can use the combination of both techniques to achieve much better accuracy and be able to get the complete set of elastic, dielectric and piezoelectric coefficients using fewer samples. Using an ultrasonic spectroscopy we have also measure the dispersion of the ultrasonic velocity and the attenuation up to 65 MHz. Pb(Zr,Ti)O$_3$[PZT] ceramics were used as examples fur both studies.

• 비파괴검사학회지
• /
• 제36권2호
• /
• pp.138-148
• /
• 2016

Measurement of elastic constants is crucial for engineering aspects of predicting the behavior of materials under load as well as structural health monitoring of material degradation. Ultrasonic velocity measurement for material properties has been broadly used as a nondestructive evaluation method for material characterization. In particular, pulse-echo method has been extensively utilized as it is not only simple but also effective when only one side of the inspected objects is accessible. However, the conventional technique in this approach measures longitudinal and shear waves individually to obtain their velocities. This produces a set of two data for each measurement. This paper proposes a simultaneous sensing system of longitudinal waves and shear waves for elastic constant measurement. The proposed system senses both these waves simultaneously as a single overlapped signal, which is then analyzed to calculate both the ultrasonic velocities for obtaining elastic constants. Therefore, this system requires just half the number of data to obtain elastic constants compared to the conventional individual measurement. The results of the proposed simultaneous measurement had smaller standard deviations than those in the individual measurement. These results validate that the proposed approach improves the efficiency and reliability of ultrasonic elastic constant measurement by reducing the complexity of the measurement system, its operating procedures, and the number of data.

• Smart Structures and Systems
• /
• 제15권6호
• /
• pp.1411-1437
• /
• 2015

The electro-magneto- thermo-elastic behavior of a rotating functionally graded long hollow cylinder with functionally graded piezoelectric (FGPM) layers is analytically analyzed. The layers are imperfectly bonded to its inner and outer surfaces. The hybrid cylinder is placed in a constant magnetic field subjected to a thermo-electro-mechanical loading and could be rested on a Winkler-type elastic foundation. The material properties of the FGM cylinder and radially polarized FGPM layers are assumed to be graded in the radial direction according to the power law. The hybrid cylinder is rotating about its axis at a constant angular velocity. The governing equations are solved analytically and then stresses, displacement and electric potential distribution are calculated. Numerical examples are given to illustrate the effects of material in-homogeneity, magnetic field, elastic foundation, applied voltage, imperfect interface and thermo-mechanical boundary condition on the static behavior of a FG smart cylinder.

• Elastomers and Composites
• /
• 제33권4호
• /
• pp.274-280
• /
• 1998

가황반응에 대한 반응차수, 반응속도상수 및 활성화에너지, 가교결합에 의한 가교밀도 및 탄성상수를 동일한 가황시스템하에서 실리카와 카본블랙을 함유한 SBR/BR 블렌드에 대하여 조사하였다. 반응차수는 충전제 종류에 관계없이 1차 반응이었으며, 카본블랙이 첨가된 배합고무는 실리카가 첨가된 배합고무보다 반응속도가 빠르게 나타났다. 그러나 활성화에너지는 충전제 종류 및 고무 블렌드 조성에 관계없이 일정하게 나타났다. 가교밀도 및 탄성상수는 고무와 카본블랙간의 강한 상호작용으로 인해 카본블랙이 첨가된 조성물에서 높게 나타났다. 한편, 고무 블렌드중 부타디엔 고무 함량이 증가할수록 가교밀도 및 탄성상수는 감소하였다. 가황고무중 결합 황 함량 비교결과, 실리카가 첨가된 조성물중 일정한 결합 황 함량은 반응시작 후 20분 후에 나타났으나, 카본블랙이 첨가된 조성물은 10분 후에 나타났다. 또한 실리카가 첨가된 조성물은 카본블랙이 첨가된 조성물에 비해 반응 유도시간($t_2$) 및 최적 가황시간($t_{90}$)이 길게 나타났다.

• Bulletin of the Korean Chemical Society
• /
• 제35권10호
• /
• pp.2941-2944
• /
• 2014

The electrical and mechanical properties of the plasma polymerized low dielectric constant SiCOH films were investigated. The SiCOH films were produced with tetrakis(trimethylsilyloxy)silane and cyclohexane as precursors by using a plasma enhanced chemical vapor deposition. When the deposition plasma powers were changed from 10 to 50 W, the relative dielectric constant of the SiCOH film increased from 2.09 to 2.76 and their hardness and elastic modulus were changed from 1.6 to 5.6 GPa and from 16 to 44 GPa, respectively. After thermal annealing at $500^{\circ}C$, the annealed SiCOH films showed relative dielectric constants of 1.80-2.97, a hardness of 0.45-0.6 GPa and an elastic modulus of 6-7 GPa. And then, the chemical structures of as-deposited and annealed SiCOH films were analyzed by using Fourier transform infrared spectroscopy.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.933-943
• /
• 2009

Axial loads and shaft resistances can be calculated by load transfer analysis using strain data with load level. In load transfer analysis, the elastic modulus of concrete is a one of the most important parameters to consider. The elastic modulus, $E_{50}$, suggested by ACI (American Concrete Institute), has been commonly used. However, elastic modulus of concrete shows nonlinear stress-strain characteristic, so nonlinearity should be considered in load transfer analysis. In this paper, a load transfer analysis was performed by using data obtained from bi-directional pile load tests for four cases of drilled shafts. For consideration of nonlinearity, elastic modulus was calculated by both the Fellenius method and the nonlinear method, assuming the stress-strain relation of concrete to be a quadratic function, and then, the calculated elastic modulus was applied to the estimation of shaft resistance. The calculated shaft resistances were compared with the result obtained using the constant elastic modulus of ACI code. It was found that the f-w curves are similar to each method, and elastic modulus and shaft resistances decreased as strain increased. Moreover, shaft resistances estimated from elastic modulus considering nonlinearity were 5~15% different than those obtained using the constant elastic modulus.

• 한국재료학회지
• /
• 제4권7호
• /
• pp.792-797
• /
• 1994

6-31G $\ast$ $\ast$ basis set을 이용한 ab initio 양자역학적 방법에 의하여 2,4,6- trifluoroheptane구조를 구함으로서 syndiotactic isoregic PVF결정의 force field를 유도하였다. 또 그 결과를 PVF의 structure parameter및 elastic constant를 계산하는데 응용하였다. 그 결과 cell parameter는 각각 a(5.205$\AA$: chain axis), b(8.457 $\AA$) 및 c(4.621 $\AA$)로 나타났으며 X-ray data(5.04$\AA$, 8.57$\AA$, 및 4.95$\AA$)결과와 비교적 잘 일치함을 알 수 있었다. Defect 비존재하에서의 syndiotactic PVF결정의 Young's 모듈러스 계산값은 267Gpa로 나타났으며, polyvinylideme fluoride(277-293 GPa)및 polyethylene(264-337 GPa)결정의 경우와 비슷한 수준으로 나타났다. 또한 optimum geometry에서 얻어진 bulk modulus값은 experimental geometry 에서 얻어진 값보다 두배의 차이를 보였으며, 이것은 geometry 에 따른 elastic compliance constant(특히 $S_{33}$인자)가 크게 달라지기 때문인 것으로 나타났다.

• 한국전기전자재료학회논문지
• /
• 제17권1호
• /
• pp.31-38
• /
• 2004

PMN-PT, a piezoelectric single crystal, has many useful applications such as sensors and actuators. In this paper, all the elastic, piezoelectric, and dielectric constants of the PMN-32％PT single crystals were measured by the resonance method. For the rhombohedral symmetry, a total of twelve independent material constants were measured such as six elastic compliance constants at constant electric field, two dielectric constants at constant stress, and four piezoelectric constants d. Seven sets of crystal samples of each different geometry were prepared for the measurement of length-thickness extensional, thickness extensional, radial, length extensional and thickness shear modes of vibration, respectively. In order to check the validity of the measurement, experimental impedance spectrum of the PMN-PT crystal was compared with numerical data spectrum calculated with the measured material constants. The good agreement between the two spectra confirmed validity of the results in this paper.

• 한국정밀공학회지
• /
• 제27권3호
• /
• pp.111-117
• /
• 2010

The repeated unit cell structure is applied to the composite, the carbon nano tube and sandwich panel. In this paper, a study on the stiffness of unit cell structure has been performed with the tube support plate of the steam generator. For this, repeated unit cell structure's equivalent elastic constant and poisson's ratio was evaluated through FEA and tests under the elastic range load. Also we evaluated the effect on the specimen size from results.

• 대한안전경영과학회지
• /
• 제7권1호
• /
• pp.211-222
• /
• 2005

The ceramic forming materials are getting more important recently since they are used widely in repairing metal structures, welded metal structures and mechanical components etc. The determination of elastic constants for ceramic coating materials takes much time and efforts in experiment due to the brittleness of ceramic material itself. The aim of this research is to determine the Young's Modulus for ceramic metal coating material. In order to achieve the goal, the hybrid method which uses impulse hammer technique for experimental method and modal analysis of finite element method for computational method was used. The results show good agreement with existing experimental data on Young's Modulus.