• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.192-192
• /
• 2008

This paper represents a piezoelectric ultrasonic linear motor by traveling wave. The motor which is composed of two piezo ceramics, elastic body, and connecting tip is driven by the frictional force between the connecting tip and the linear motion guide. longitudinal and flexural vibrations are made by traveling wave which is generated when the ultrasonic electrical signals with 90 degree phase difference are applied to two ceramics. These vibrations contribute to elliptical motion by mixed mode between longitudinal and transverse mode. A linear movement can be easily obtained by using the elliptical motion. In this paper, the piezoelectric actuator has been intensively simulated by using ATILA to achieve an optimized elliptical motion of it. We could get the elliptical motion from actual experiment through the simulated result.

• Journal of Ocean Engineering and Technology
• /
• v.7 no.2
• /
• pp.19-29
• /
• 1993

The static tensile tests of GFRP, ID300, CFRID300 and CFRPEEK were made on the plain and notched specimens at room temperature. The results were discussed based on linear notch mechanics which was proposed by H.Nistani. The fracture of notched GFRP, ID300, CFRID300 and CFRPEEK specimens is controlled by the elastic maximum stress, $({\sigma}_max)$, and the notch root racius,$\rho$, alone, independently of the other geometrical conditions. The relation between fracture nominal stress,$({\sigma}_max)$, and stress concentration factor, $K_t$ and a part where $({\sigma}_c)$ is nearly constant independent of $K_t$. A similar phenomenon can be seen in the fatigue tests of notched specimes under rotating bending or push-pull. The almost constant $({\sigma}_c)$ values correspond to the nearly constant apparent stress intensity factor, $K_{1pc}$ values, obtained by assuming ,$\rho$=0. This can be attributed to the existence of the stable crack. Linear notch mechanics is very useful for analyzing the static tensile fracture behavior of notched GFRP, ID300, CFRPEEK specimens.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.5
• /
• pp.1190-1201
• /
• 1995

Photoelastic experiment has been restricted by three significant problems such as the problems of modeling for a complicated body, of development of experimental model material, and of residual stress in photoelastic specimen. The residual stress in photoelastic model materials is caused by molding, cutting and time effects, etc.. Especially, large residual stress exists on the interface of photoelastic model material for bi-material. Small residual stress occurred in the photoelastic model materials is usually neglected in the photoelastic experiments. But the residual stress provides some errors in the results of photoelastic experiments. In this paper, the stress optic law which can be effectively applied to the phtoelastic model materials with residual stress is developed. By using this stress optic law, we can obtain good results from isochromatic fringe patterns of photoelastic experiment specimen in which residual stress are involved. The stress optic law can be applied to obtain good results of photoelastic experiment from composite materials or bimaterials.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.438-444
• /
• 2003

A new method to measure residual stress in micron and nano scale films is described. In the theory it is based on Linear Elastic Fracture Mechanics. And in the techniques it depends on the combined capability of the focused ion beam (FIB) imaging system and of high-resolution digital image correlation (DIC) software. The method can be used for any film material (whether amorphous or crystalline) without thinning the substrate. In the method, a region of the film surface is highlighted and scanning electron images of that region taken before and after a long slot, depth a, is introduced using the FIB. The DIC software evaluates the displacement of the surface normal to the slot due to the stress relaxation by using features on the film surface. To minimize the influence of signal noise and rigid body movement, not a few, but all of the measure displacements are used for determining the real residual stress. The accuracy of the method has been assessed by performing measurements on a nano film of diamond like carbon (DLC) on glass substrate and on micro film of aluminum oxide thermally grown on Fecrally substrate. It is shown that the new method determines the residual stress ${\sigma}_R=-1.73$ GPa for DLC and ${\sigma}_R=-5.45$ GPa for the aluminum oxide, which agree quite well with ones measured independently.

• Journal of computational fluids engineering
• /
• v.15 no.4
• /
• pp.1-8
• /
• 2010

This article describes the numerical investigation of turbulent blood flow in the stenosed artery bifurcation under periodic acceleration of the human body. Numerical analyses for turbulent blood flow were performed with different magnitude of periodic accelerations using a modified turbulence model which was considering drag reduction of non-Newtonian fluid. The blood was considered to be a non-Newtonian fluid which was based on the power-law viscosity. In order to validate the modified $k-{\varepsilon}$ model, numerical simulations were compared with the standard $k-{\varepsilon}$ model and the Malin's low Reynolds number turbulence model for power-law fluid. As results, the modified $k-{\varepsilon}$ model represents intermediate characteristics between laminar and standard $k-{\varepsilon}$ model, and the modified $k-{\varepsilon}$ model showed good agreements with Malin's verified power law model. Moreover, the computing time and computer resource of the modified $k-{\varepsilon}$ model were reduced about one third than low Reynolds number model including Malin's model.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.12
• /
• pp.3018-3025
• /
• 2000

It is possible to shorten developing process by making model using polyurethane foam in the area of automobile development process, etc. However, this skill is too difficult to be of practical use because machining is not easy due to characteristic of polyurethane foam. Domestic and foreign automobile company use clay, polyurethane foam. etc,, those are easy to handle and to make model after completing design sketch. But these materials is difficult to the machined and be worked by humans hand, There are so many difficult problem for machining by making model using polyurethane foam since cutting of elastic body like polyurethan foam has never been studied. Therefore, in this study, it is investigated to measured cutting force that is generated in case of polyurethane foam machining, and to make systematize tool compensation of polyurethane foam cutting work on automobile model by modification of tool offset method on existing steel.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.6
• /
• pp.946-953
• /
• 2003

A FEM-based analytical approach was used to evaluate the multiaxial high cycle fatigue damage of an automotive sub-frame. Elastic Multi Body Simulation (MBS) has been applied in order to determine the multiaxial load histories. The stresses due to these loads have been given by FE computation. These results have been used as the input for the multiaxial fatigue analysis. For the assessment of multiaxial high cycle fatigue damage, the signed von Mises, the signed Tresca, the absolute maximum principal stress and critical plane methods have been employed. In addition, the biaxiality ratio, a$\sub$e/, the absolute maximum principal stress, $\sigma$$\sub$p/ and the angle, $\phi$$\sub$P/, between $\sigma$$\sub$1/ and the local x-axis, have been calculated to evaluate the stress state at each node.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.27 no.11
• /
• pp.1190-1197
• /
• 2003

The purpose of this study is to compare and analyze methods of women's apparel prototypes and provide for some useful fundamental data to improve the apparel prototype suitable for Korean women. Two different drafting methods, the Bunka pattern of Japan Bunka Women's University and the Secoli pattern of Italy istituto carlo secoli, an italian pattern drafting institute, were selected. The result and discussion are as follows; In the calculation formula, the Bunka was shown more comfort at arm-hole part, because of it's lower arm-hole depth, wider arm-hole width and lower cap height in comparison with the Secoli. At the shoulder angle, the Bunka is inclined more in front shoulder than the back shoulder, whereas the Secoli is inclined more in back shoulder than the front shoulder. It could explain that the Bunka is suitable for bendforward type and the Secoli is suitable for lean-back type. In the sensory test, the one-piece pattern of the Secoli with 4cm ease was highly estimated in ease. It seems young women's preference to body conscious clothes which reflected in many new elastic fabrics. At the bust point to neck, the Bunka was highly estimated, compared with the Secoli. It seems like to be caused that for the bust point to neck formula, the Bunka used bust girth, the Secoli used stature which has low correlation with the bust point to neck.

• Computers and Concrete
• /
• v.14 no.1
• /
• pp.91-107
• /
• 2014

Using the principle of damage mechanics, zero-thickness pore pressure cohesive elements (PPCE) are used to simulate the casing-cement interface (CCI) and cement-rock interface (CRI). The traction-separation law describes the emergence and propagation of the PPCE. Mohr-coulomb criteria determines the elastic and plastic condition of cement sheath and rock. The finite element model (FEM) of delamination fractures emergence and propagation along the casing-cement-rock (CCR) interfaces during hydraulic fracturing is established, and the emergence and propagation of fractures along the wellbore axial and circumferential direction are simulated. Regadless of the perforation angle (the angle between the perforation and the max. horizontal principle stress), mirco-annulus will be produced alonge the wellbore circumferential direction when the cementation strength of the CCI and the CRI is less than the rock tensile strength; the delamination fractures are hard to propagate along the horizontal wellbore axial direction; emergence and propagation of delamination fractures are most likely produced on the shallow formation when the in-situ stresses are lower; the failure mode of cement sheath in the deep well is mainly interfaces seperation and body damange caused by cement expansion and contraction, or pressure testing and well shut-in operations.

• Structural Engineering and Mechanics
• /
• v.67 no.1
• /
• pp.9-20
• /
• 2018

In this paper, a framework is proposed for dynamic analysis of train-bridge systems with a damaged pier after barge collision. In simulating the barge-pier collision, the concrete pier is considered to be nonlinear-inelastic, and the barge-bow is modeled as elastic-plastic. The changes of dynamic properties and deformation of the damaged pier, and the additional unevenness of the track induced by the change of deck profile, are analyzed. The dynamic analysis model for train-bridge coupling system with a damaged pier is established. Based on the framework, an illustrative case study is carried out with a $5{\times}32m$ simply-supported PC box-girder bridge and the ICE3 high-speed train, to investigate the dynamic response of the bridge with a damaged pier after barge collision and its influence on the running safety of high-speed train. The results show that after collision by the barge, the vibration properties of the pier and the deck profile of bridge are changed, forming an additional unevenness of the track, by which the dynamic responses of the bridge and the car-body accelerations of the train are increased, and the running safety of high-speed train is affected.