• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.8 no.2
• /
• pp.155-166
• /
• 1988

An "equivalent homogeneous, orthotropic" model that includes edge effects and an accompanying finite element analysis is presented for elastomeric bearings. The model is developed for two-dimensional configurations with horizontal layers, and for linear, elastic, small deformation conditions. The equivalent homogeneous theory, in addition to capturing the overall response characteristics of the layered elastomeric bearing system, approximately models the important edge effects, which occur at and near boundaries that cut the layers, and the stress concentrations at layer interfaces. The primary dependent variables for the theory have been selected such that the highest derivatives appearing in the strain energy function are first-order, thus requiring only $C_0$ continuity of the finite element approximations. As a result, the finite element analysis is simple and computationally efficient. Numerical examples are presented to verify the theory and to illustrate potential applications of the analysis.

• Composites Research
• /
• v.24 no.3
• /
• pp.25-30
• /
• 2011

The studies on the non-destructive testing methods of the composite materials are very important for improving their reliability and safety. AE(Acoustic Emission) can evaluate the defects by detecting the emitting strain energy when elastic waves are generated by the generation and growth of a crack, plastic deformation, fiber breakage, matrix cleavage or delamination. In this paper, the AE signals of the filament wound composite cylinder and sandwich cylinder during the pressure test were measured and analyzed. The signal characteristics of PVDF sensors were measured, and an AE signal analyzer which had the band-pass filter and L-C resonance filter were designed and fabricated. Also, the crack detection capability of the fabricated AE signal analyzer wes evaluated during the pressure tests of the filament wound composite cylinder and the sandwich cylinder.

• Tribology and Lubricants
• /
• v.24 no.6
• /
• pp.297-301
• /
• 2008

In many dynamic seals such as lip seal and compression packings, it is well known that wear occur at the surface of heat treated steel shaft as results of the intervened wear particle. It is widely understood that the dominant wear mechanism related in sealing surfaces is abrasive wear. However, little analytical and experimental studies about this problems have been done until now. In this paper, a contact analysis is carried out using MARC to investigate the wear mechanism in contact seal applications considering elastomeric seal, a elastic perfect-plastic micro-spherical particle and steel surface. Deformed seal shapes, contact and von-Mises stress distributions for various particle sizes and interference are showed. The maximum von-Mises stress within steel shaft was exceeded its yield strength and plastic deformation occurred at steel surface. Therefore, the sealing surface can be also worn by sub-surface fatigue due to wear particles together with well known abrasion. The numerical methods and models used in this paper can be applied in design of dynamic sealing systems, and further intensive studies are required.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.10a
• /
• pp.79-82
• /
• 2004

In this study, a new refinement technique for 3-dimensional hexahedral element mesh is proposed, which is aimed at the control of mesh density. With the proposed scheme the mesh is refined adaptively to the elemental error which is estimated by 'a posteriori' error estimator based on the energy norm. A desired accuracy of an analysis i.e. a limit of error defines the new desired mesh density map on the current mesh. To obtain the desired mesh density, the refinement procedure is repeated iteratively until no more elements to be refined exist. In the algorithm, at first the regions of mesh to be refined are defined and, then, the zero-thickness element layers are inserted into the interfaces between the regions. All the meshes in the regions, in which the zero-thickness layers are inserted, are to be regularized in order to improve the shape of the slender elements on the interfaces. This algorithm is tested on a simple shape of 2-d quadrilateral element mesh and 3-d hexahedral element mesh. A numerical example of elastic deformation of a plate with a hole shows the effectiveness of the proposed refinement scheme.

• Tribology and Lubricants
• /
• v.30 no.2
• /
• pp.77-85
• /
• 2014

This study set out to predict the load capacity and rotordynamic coefficients of tilting-pad journal bearings, taking the pivot stiffness into account. The analysis uses rocker-back (cylindrical) and ball in socket (spherical) pivot models, both of which are based on Hertzian contact stress theory. The models ascertain the non-linear elastic deformation of the pivots according to the applied load, pivot geometry, and material properties. At present, the Reynolds equation for an isothermal, isoviscous, and incompressible fluid is used to calculate the film pressure by using the finite-element method, after which the Newton-Raphson method is used to simultaneously find the journal center location, pad angles, and pivot deflections. The bearing analysis, excluding the pivot models, is validated using predictions those are readily available in the literature. As the rotor speed increases, the predicted journal eccentricity and damping coefficients decrease, but the stiffness coefficients increase, as expected. Most importantly, the implementation of the pivot models increases the journal eccentricity but significantly decreases the stiffness and damping coefficients of the tilting-pad journal bearings.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.8
• /
• pp.26-32
• /
• 1998

The grinding force generated during the grinding process causes an elastic deformation of the workpiece, grinding wheel, and machine system. Thus, the true depth of cut is always smaller than the apparent depth of cut. This is known as machining elasticity phenomenon. The machining elasticity parameter is defined as a ratio between the true depth of cut and the apparent depth of cut. It is an important factor to understand the material removal mechanism of the grinding process. To increase productivity, the value of this machining elasticity parameter must be large. Therefore, it is essential to know the characteristics of this parameter. The objective of this research is to study the effect of the major grinding conditions, such as table speed and depth of cut, on this parameter experimentally. Through this research, it is found that this parameter value is increasing when the table speed is decreasing or the depth of cut is increasing. Also, this parameter value depends on the grinding mode (up grinding, down grinding).

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.2
• /
• pp.180-187
• /
• 2005

This paper is focused on the development of the flexible electrode for disc-type polymer actuators using Segmented Polyurethane(SPU). This paper consists of two parts. The one is about the mechanical property such as elastic modulus. these parameters mainly affect behaviors of polymer actuators and the other is about the electro-chemical property such as the surface resistance of the composite electrode affects the strength of electrostatic force, results in the deformation of polymer actuators. The Young's modulus was measured by UTM. As result, by increasing the modulus of a body of polymer actuators, the maximum displacement of polymer actuators are decreased. The surface resistance of the electrode was measured by 4 point probe system. Compared with the conductive silver grease, the displacement of polymer actuators using carbon black(CB) composite electrodes is comparably small but CB composite electrode should be the practical approach for the improvement of the performance of all-solid actuators, compared with another types of electrode materials.

• Journal of the Korean Society of Industry Convergence
• /
• v.4 no.3
• /
• pp.257-261
• /
• 2001

이 연구는 밀링가공시 체터진동을 억제하기 위하여 부등각 앤드밀(나선각이 서로 다른 앤드밀)을 사용하여 절삭가공을 수행 한 후, 그 가공특성을 고찰한 것으로 가공표면의 기하학적 오차를 일반적으로 사용하는 등각 엔드밀에 의한 값과 실험에 의해 비교 검토한 결과, 두 엔드밀 모두 가공표면의 기하학적 오차는 유사함 나타내고 있으나, 부등각 엔드밀의 절대오차는 등각 엔드밀 보다 더 적은 경향을 나타내고 있다. 이들의 오차는 상향절삭보다 하야절삭 가공했을 때가 더 큰 것으로 나타났다. 더구나, 등각 엔드밀과 부등각 엔드밀과의 절대오차가 다르게 나타난 것은 밀링가공시 사용한 절삭날 인선에 의하여 완전히 의존되어지며, 또한 다른 나선각에 의해 기인된 각각의 절삭날에 대한 절삭날당 이송비의 변화에 의한 원인이라는 것을 명백히 알 수 있었다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.65-69
• /
• 2002

In order to practicalize high precision centerless grinder for machining the ferrule, its feeding system is designed and tested. For satisfying the desired diametric tolerance and cylindricity of the ferrule, the feeding system is designed to have relatively high axial stiffness of 600 N/$\mu\textrm{m}$, high angular motion accuracy of 0.5 arcsec/mm in yaw direction and minimum resolution of 0.05 $\mu\textrm{m}$. A prototype of feeding system is built up with hydrostatic guideway and ballscrew. A linear scale with 0.05 $\mu\textrm{m}$ of resolution is used for position feedback. Experimental results show that the feeding system has the infinity of axial stiffness within the range of 1000 N and 0.3 arcsec/mm of yawing error. Also the feeding system shows obvious step response against 0.05 $\mu\textrm{m}$/step command without the lost motion or backlash. Although the vertical stiffness is reduced to 440 N/$\mu\textrm{m}$ by the elastic deformation of rail, it is good enough to use for machining the ferrule. From above, it is confirmed that the feeding system is applicable to centerless grinder for machining the ferrule.

• Transactions of Materials Processing
• /
• v.8 no.3
• /
• pp.259-259
• /
• 1999

TiC ceramic particulate-reinforced titanium matrix composites were fabricated and the resultant densification, microstructure, and static and dynamic mechanical properties were studied. Comparing Ti with TiH₂powders as host materials for TiC ceramic reinforcement by pressureless vacuum sintering, TiH₂-started composites showed better sinterability and resistance to both elastic and plastic deformation than Ti-started ones. When TiH₂and TiH₂-45 vol.%TiC samples were hot pressed, TiH₂matrices transformed to alpha prime Ti and alpha Ti phase, respectively. It is interpreted that the diffusion of an alpha stabilizer carbon from TiC into the matrix is one of the plausible reasons far such a microstructural difference. The 0.2% offset yield strengths of the hot pressed TiH₂and TiH₂-45 vol.%TiC samples were 1008 and 1446 MPa, respectively, in a static compressive mode (strain rate of 1×$10^{-3}$/s). Dynamic compressive strengths of the samples were 1600 and 2060 MPa, respectively, at a strain rate of 4×10³/s.