• 한국산학기술학회논문지
• /
• 제18권7호
• /
• pp.9-16
• /
• 2017

콘크리트 충전 강관 기둥을 개선한 팔각 콘크리트 충전 강관 기둥 (OCFT 기둥)이 개발되었다. 본 연구에서는 시공성 및 경제성 측면에서 장점을 갖는 OCFT 기둥을 역타(Top-Down) 공법에 적용하기 위하여 원심모형실험 장비를 활용하여 압축성능을 검증하였다. 12 g의 원심가속도가 작용하는 상태에서 말뚝으로 시공된 OCFT 기둥의 시공하중에 대한 지지가능 여부와 토사가 굴토되었을 경우 말뚝의 좌굴안전성 등을 관찰하기 위하여 압축강도에 대한 실험을 수행하였다. 천공 후, OCFT 기둥과 H 형강이 말뚝기초로 시공되고 뒷채움으로, 지반에 완전히 묻힌 실험체의 경우와 반만 묻힌 경우에 대하여, 약 13,000 kN의 공칭강도의 45% 시공하중을 재하한 결과 모든 실험체가 탄성상태에서 거동하였다. 하중재하실험 종료 후, 풍화암과 말뚝하부를 관찰한 결과 풍화암이 손상되지 않았으며, 이로부터 3.5 MPa 조성된 풍화암은 $600{\times}600mm$ OCFT 기둥의 공칭강도의 45%도 안정적으로 지지할 수 있는 것으로 판단된다.

• Steel and Composite Structures
• /
• 제17권4호
• /
• pp.471-495
• /
• 2014

The responses of steel buildings with perimeter moment resisting frames (PMRF) with medium size columns (W14) are estimated and compared with those of buildings with deep columns (W27), which are selected according to two criteria: equivalent resistance and equivalent weight. It is shown that buildings with W27 columns have no problems of lateral torsional, local or shear buckling in panel zone. Whether the response is larger for W14 or W27 columns, depends on the level of deformation, the response parameter and the structural modeling under consideration. Modeling buildings as two-dimensional structures result in an overestimation of the response. For multiple response parameters, the W14 columns produce larger responses for elastic behavior. The axial load on columns may be significantly larger for the buildings with W14 columns. The interstory displacements are always larger for W14 columns, particularly for equivalent weight and plane models, implying that using deep columns helps to reduce interstory displacements. This is particularly important for tall buildings where the design is usually controlled by the drift limit state. The interstory shears in interior gravity frames (GF) are significantly reduced when deep columns are used. This helps to counteract the no conservative effect that results in design practice, when lateral seismic loads are not considered in GF of steel buildings with PMRF. Thus, the behavior of steel buildings with deep columns, in general, may be superior to that of buildings with medium columns, using less weight and representing, therefore, a lower cost.

• 한국강구조학회 논문집
• /
• 제16권5호통권72호
• /
• pp.653-660
• /
• 2004

도심지의 토지 이용률을 높이기 위하여 상대적으로 단면이 작은 원형 강교각의 건설이 요구되고 있다. 이때 줄어든 단면으로 인해 감소된 좌굴내하력을 높이는 방안으로 수직보강재의 적용을 고려할 수 있다. 그러나 수직보강재를 적용함으로써 얻어질 수 있는 좌굴내하력의 증가효과는 아직 명확하지 않다. 본 연구에서는 기하학적, 재료학적 비선형을 고려한 탄소성 유한요소해석을 수행하여 원형강교각의 반지름-두께비에 따른 수직보강재의 수가 좌굴내하력에 미치는 영향을 명확히 하였다. 또한, 수직보강재의 폭과 두께, 원형강교각의 세장비에 따른 좌굴해석을 수행하여 그 관계를 명확히 하였다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제19권6호
• /
• pp.1-9
• /
• 2015

횡방향철근은 기둥의 소성힌지구간에 충분한 구속효과, 축방향철근의 좌굴방지와 연성거동을 확보하기 위해 적용된다. 기둥에서 사각형 후프 띠철근과 보강 띠철근의 조립 및 배근방법은 시공이 까다롭고 많은 횡방향철근량이 요구된다. 본 논문에서, 이러한 문제점들을 해결하기 위하여 장방형 단면과 플레어 기둥의 횡구속을 위한 장방형 후프 띠철근을 사용한 새로운 횡구속 방법이 제안되었다. 개발된 장방형 후프 띠철근 상세는 장방형 단면과 플레어 기둥의 시공성과 경제성을 향상시켜줄 수 있는 하나의 대안으로서 적용 가능한 것으로 판단된다. 본 연구의 최종목적은 철근콘크리트 교각의 시공성 향상을 위한 장방형 후프 띠철근 상세의 제시와 실험적 기초자료의 제공과 함께 하중단계별 성능 및 손상평가를 위한 정량적 수치와 경향을 제공하기 위한 것이며, 극한변위, 극한드리프트비율, 변위연성도, 응답수정계수, 등가점성감쇠비, 잔류변형지수, 유효강성 등의 주요 내진성능평가 변수들에 대한 분석결과를 나타내었다.

• 대한기계학회논문집A
• /
• 제34권11호
• /
• pp.1659-1666
• /
• 2010

WBD(wire-woven bulk diamond)라고 명명한 와이어로 직조된 다공질 금속의 새로운 형태를 소개한다. WBD 는 기계적 열 특성과 공학적 응용면에서 몇 년 전에 소개되어진 WBK(wire-woven bulk Kaogme)와 같이 나선형 와이어로 구성된다. WBK 에서는 각 교차점에서 3 개의 와이어가 접하나 WBD 에서는 4 개의 와이어가 서로 접하여 배열된다. 압축하중 하에서 WBD 의 기계적 거동을 조사하고 그 결과를 WBK 와 비교하였다. 같은 세장비(d/c)에서 WBD 의 밀도 및 강도는 WBK 의 약 2 배이나, WBD 의 강성도는 WBK 보다 그만큼 높지 않다.

• Steel and Composite Structures
• /
• 제33권4호
• /
• pp.569-581
• /
• 2019

Corrugated steel plate shear wall (CSPSW) as an innovative lateral load resisting system provides various advantages in comparison with the flat steel plate shear wall, including remarkable in-plane and out-of-plane stiffnesses and stability, greater elastic shear buckling stress, increasing the amount of cumulative dissipated energy and maintaining efficiency even in large story drifts. Employment of low yield point (LYP) steel web plate in steel shear walls can dramatically improve their structural performance and prevent early stage instability of the panels. This paper presents a comprehensive structural performance assessment of corrugated low yield point steel plate shear walls having circular openings located in different positions. Accordingly, following experimental verification of CSPSW finite element models, several trapezoidally horizontal CSPSW (H-CSPSW) models having LYP steel web plates as well as circular openings (for ducts) perforated in various locations have been developed to explore their hysteresis behavior, cumulative dissipated energy, lateral stiffness, and ultimate strength under cyclic loading. Obtained results reveal that the rehabilitation of damaged steel shear walls using corrugated LYP steel web plate can enhance their structural performance. Furthermore, choosing a suitable location for the circular opening regarding the design purpose paves the way for the achievement of the shear wall's optimal performance.

• Steel and Composite Structures
• /
• 제23권4호
• /
• pp.473-481
• /
• 2017

Steel plate shear wall (SPSW) system has been increasingly used for lateral loads resisting system since 1980s when the utilization of post-buckling strength of SPSW was realized. The structural response of SPSWs largely depends on the behavior of the surrounded beams. The beams are normally required to behave in the elastic region when the SPSW fully buckled and formed the tension field action. However, most modern design codes do not specify how this requirement can be achieved. This paper presents theoretical investigation and design procedures of manually calculating the plastic flexural capacity of the beams of SPSWs and can be considered as an extension to the previous work by Qu and Bruneau (2011). The reduction in the plastic flexural capacity of beam was considered to account for the presence of shear stress that was altered towards flanges at the boundary region, which can be explained by Saint-Venant's principle. The reduction in beam web was introduced and modified based on the research by Qu and Bruneau (2011), while the shear stress in the web in this research is excluded due to the boundary effect. The plastic flexural capacity of the beams is given by the superposition of the contributions from the flanges and the web. The developed equations are capable of predicting the plastic moment of the beams subjected to combined shear force, axial force, bending moment, and tension fields induced by yielded infill panels. Good agreement was found between the theoretical results and the data from previous research for flexural capacity of beams.

• Advances in aircraft and spacecraft science
• /
• 제6권2호
• /
• pp.117-144
• /
• 2019

High Altitude and Long Endurance (HALE) aircraft are capable of providing intelligence, surveillance and reconnaissance (ISR) capabilities over vast geographic areas when equipped with advanced sensor packages. As their use becomes more widespread, the demand for additional range, endurance and payload capability will increase and designers are exploring non-conventional configurations to meet the increasing demands. One such configuration is the joined-wing concept. A joined-wing aircraft is one that typically connects a front and aft wings in a diamond shaped planform. One such example is the Boeing SensorCraft configuration. While the joined-wing configuration offers potential benefits regarding aerodynamic efficiency, structural weight, and sensing capabilities, structural design requires careful consideration of elastic buckling resulting from the aft wing supporting, in compression, part of the forward wing structural loading. It has been shown already that this is a nonlinear phenomenon, involving geometric nonlinearities and follower forces that tend to flatten the entire configuration, leading to structural overload due to the loss of the aft wing's ability to support the forward wing load. Severe gusts are likely to be the critical design condition, with flight control system interaction in the form of Gust Load Alleviation (GLA) playing a key role in minimizing the structural loads. The University of Victoria Center for Aerospace Research (UVic-CfAR) has built a 3-meter span scaled and flexible wing UAV based on the Boeing SensorCraft design. The goal is to validate the nonlinear structural behavior in flight. The main objective of this research work is to perform Ground Vibration Tests (GVT) to characterize the dynamic properties of the scaled flight vehicle. Results from the experimental tests are used to characterize the modal dynamics of the aircraft, and to validate the numerical models. The GVT results are an important step towards a safe flight test program.

• 한국융합학회논문지
• /
• 제10권4호
• /
• pp.139-145
• /
• 2019

이 논문은 복합 입체형 트러스 단위구조체에 대한 강도 및 강성을 연구하였다. 사용된 모델은카고메 모델과 정육면체 트러스 모델을 합한 core-filled 모델이다. 해석을 위해 사용한 재질 특성은 304 스테인레스 스틸로 탄성계수는 193GPa, 항복응력 215MPa이다. 이론식은 깁슨-애쉬비의 상대탄성 관계식을 바탕으로 이론식을 유도하였고, 상용도구인 Deform 3D를 사용하여 해석을 실시하였다. 결론적으로 이 단위모델에 대한 상대탄성력은 상대밀도의 1.25배와 상수 계수값과 상관관계를 형성하고, 탄성은 기공과 반비례한다. 그리고, 상대압축강도는 상대밀도와 1.25배의 상관관계를 이룬다. 이에 대한 증명은 실제 실험을 해야 하겠으며, 유도한 이론 관계식은 굽힘과 좌굴등의 기계적 거동을 추가로 고려해야 한다. 앞으로 입체공간의 구조에 따른 탄성 및 응력에 대해 지속적인 연구가 진행될 것이다.

• 국제강구조저널
• /
• 제18권5호
• /
• pp.1617-1630
• /
• 2018

The crucial differences between conventional rail with split-type connectors and continuous welded rails are axial stress in the longitudinal direction and stability, as well as other issues generated under the influence of loading effects. Longitudinal stresses generated in continuously welded rails on railway bridges are strongly influenced by the nonlinear behavior of the supporting system comprising sleepers and ballasts. Thus, the track structure interaction cannot be neglected. The rail-support system mentioned above has properties of non-uniform material distribution and uncertainty of construction quality. The linear elastic hypothesis therefore cannot correctly evaluate the stress distribution within the rails. The aim of this study is to apply the nonlinear finite element method using the nonlinear coupling interface between the track and structural model and to illustrate the welded rail behavior under the loading effect and uncertain factors of the ballast. Numerical results of nonlinear finite analysis with a three-dimensional solid and frame element model are presented for a typical track-bridge system. A composite plate girder, modeled by solid and shell elements, is also analyzed to consider the behavior of the welded rail. The analysis result showed buckling under the independent calculations of load cases, including 'temperature change', 'bending of the supporting structure', and 'braking' of the railway vehicle. A parametric study of the load combination method and the loading sequence is also included in this analysis.