• Journal of Power Electronics
• /
• 제19권1호
• /
• pp.307-315
• /
• 2019

Condition monitoring has been recognized as an effective and low-cost method to enhance the reliability and improve the maintainability of power electronic converters. In power electronic converters, high-frequency oscillation occurs during the switching transients of power transistors, which is known as ringing. The ringing frequency mainly depends on the values of the parasitic capacitance and stray inductance in the oscillation loop. Although circuit stray inductance is an important factor that leads to the ringing, it does not change with transistor aging. A shift in either the inside inductance or junction capacitance is an important failure precursor for power transistors. Therefore, ringing frequency can be used to monitor the health of power transistors. However, the switching actions of power transistors usually result in a dynamic behavior that can generate oscillation signals mixed with background noise, which makes it hard to directly extract the ringing frequency. A frequency extraction method based on empirical mode decomposition (EMD) and Fast Fourier transformation (FFT) is proposed in this paper. The proposed method is simple and has a high precision. Simulation results are given to verify the ringing analysis and experimental results are given to verify the effectiveness of the proposed method.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년 학술대회 논문집 정보 및 제어부문
• /
• pp.235-237
• /
• 2006

In this paper, the previous 2-D gradient coil design method using loop current elements is extended to 3-D or multi-layer structures which is useful for various MRI applications including MR microscopic imaging where relatively large space may be available for the implementation of the gradient coils. Either the power consumption or the stored energy (thus, inductance), or the combination of the two can be minimized with a set of chosen target field constraints. Complete 3-D design equations for the optimization as well as inductance or resistance calculation are derived. An effective coil shape correction method for a curved current pattern is also developed. The design method can also be easily extended to the active shielding structure.

• 한국전기전자재료학회논문지
• /
• 제17권5호
• /
• pp.502-507
• /
• 2004

The forward planar transformer, which had power capacity of 300 W, input voltage of 220 V, output voltage of 15 V, and switching frequency of 300 KHz, was designed and manufactured by using the planar core with large effective area and the flat copper leadframes for miniaturization and high efficiency of the switching mode power supply (SMPS). As well as, a forward converter equipped with the above mentioned planar transformer was manufactured and electromagnetic characteristics were investigated. The numerical value of turns for 1st and 2nd winding were 15 and 2 respectively The self inductance of 1st winding was 1.592 mH, very low leakage inductance of 2.7 $\mu$H, and the coupling factor of 0.928 were obtained at switching frequency of 300 KHz. The high efficiency of 88.62 % for the SMPS equipped with planar transformer was obtained at power capacity of 300 W.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 F
• /
• pp.2085-2087
• /
• 1998

This paper presents the design method of a dimming electronic ballast for fluorescent lamps using a frequency control IC, and investigates the effects of circuit variables on its dimming characteristics. It is shown that effective dimming is possible with IC IR2151 for frequency control, and this leads to a feasible design of more smaller and cheaper dimming ballast. Five ballasts different in the values of the series inductance and capactance are designed, and their dimming characteristics are compared. As the result, the dimming range becomes more broader as the series inductance gets smaller and the capacitance larger. Thus appropriate selection of the values of L and C should be made according to the types of application site.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 C
• /
• pp.2235-2237
• /
• 2005

This paper presents the transient impedance behaviors of grounding systems to lightning impulse current. The potential rise and effective impulse ground impedance of the test grounding electrodes were measured as a function of the rise time of impulse currents and lengths of down conductor. The transient ground impedances strongly depend on the configuration and size of grounding electrodes, the impulse current shapes and lengths of down conductor, and the inductance of reduce of grounding electrode inductance is an important factor to improve the transient ground impedance.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 제38회 하계학술대회
• /
• pp.1013-1014
• /
• 2007

This paper presents the design of Brushless DC (BLDC) motor using parametric design. According to the variation of magnitude of back emf and inductance, characteristic equations of BLDC motor are solved then output power, current, and torque ripples are calculated. Therefore output characteristics of BLDC motor according to motor parameter can be easily understood, and the range of back emf and inductance satisfying required output performance can be easily found. Presented design method leads to the BLDC motor design to be simple and effective, and the optimal design of BLDC motor using parametric design for 3kW with 50000rpm is presented.

• 한국수산과학회지
• /
• 제54권6호
• /
• pp.1036-1044
• /
• 2021

A linear array acoustic transducer with 12 tonpilz elements mounted independently on a gradual wedge-shaped tail mass was fabricated, tested and analyzed. The compensated transducer, which is modified by including a series inductance of 137 µH in the developed linear array transducer, attained improved figure of merit (FOM) performance characteristics compared with the uncompensated transducer. The four resonant frequency bands were identified from the measured FOM curve. The FOM response patterns over the frequency ranges of 31 to 40 kHz and 50 to 60 kHz were relatively uniform, whereas sharp resonance peaks were observed at around 73 kHz and 84 kHz. These results indicate that the developed linear array transducer can be used as an enhanced broadband transducer of echo sounder, and the operating frequency can be selected for more effective echo surveys in the fishing ground.

• 한국항행학회논문지
• /
• 제28권2호
• /
• pp.246-249
• /
• 2024

In this paper, we present a miniaturized differential line (DL) using inductance-enhanced corrugated ground planes (LCGP) for effective common-mode (CM) noise suppression in high-speed packages and printed circuit boards. The LCGP-DL demonstrates the CM noise suppression in the frequency range from 2.09 GHz to 3.6 GHz. Furthermore, to achieve the same low cutoff frequency, the LCGP-DL accomplishes a remarkable 23.2% reduction in size compared to a reference DL.

• 전력전자학회논문지
• /
• 제4권1호
• /
• pp.50-56
• /
• 1999

본 연구에서는 시간영역에서 전력이 해석되어지므로 이해하기 쉽고, 비교적 계측하기 용이한 상관함수에 의한 순시전력이론에 대해서 고찰하였다. 상관함수에 의한 순시전력이론은 시간영역에서 전압과 전류의 자기상관함수와 상호상관함수에 의해서 전력과의 전압과 상관성에 따라 상관전력과 비상관 전력으로 분해된다. 분해된 두 가지 전력성분으로부터 비선형 부항의 특성에 따라 전력과 전류를 유효성분, 기본파 무효성분 그리고 고조파성분 등 3성분으로 분해한다. 능동전력필터는 그 보상특성상 전력과 전류의 3성분만을 다루며, 실시간 제어를 위해 그외의 여러 복잡한 그리고 구현의 어려움이 있는 전력모델은 경제적이지 못하다. 상관함수적인 순시전력이론에 의해 분석된 전력성분들의 타당성을 입증하기 위해서 전압형 DSP능동전력필터를 제작하였다. 싸이리스터 제어 유도전동기 구동시스템의 전력을 제안된 순시전력이론에 의해 3성분으로 분해한 후, 이들 성분중에서 보상기준전류로 고조파성분과 기본파 무효성분을 각각 제어하여 그 보상결과로부터 타당성을 입증하였다.

• Journal of Power Electronics
• /
• 제16권1호
• /
• pp.362-373
• /
• 2016

The on-line measurement of high-power IGBT collector current is important for the hierarchical control and short-circuit and overcurrent protection of its driver and the sensorless control of the converter. The conventional on-line measurement methods for IGBT collector current are not suitable for engineering measurement due to their large-size, high-cost, low-efficiency sensors, current transformers or dividers, etc. Based on the gate driver, this paper has proposed a current measuring circuit for IGBT collector current. The circuit is used to conduct non-intervention on-line measurement of IGBT collector current by detecting the voltage drop of the IGBT power emitter and the auxiliary emitter terminals. A theoretical analysis verifies the feasibility of this circuit. The circuit adopts an operational amplifier for impedance isolation to prevent the measuring circuit from affecting the dynamic performance of the IGBT. Due to using the scheme for integration first and amplification afterwards, the difficult problem of achieving high accuracy in the transient-state and on-state measurement of the voltage between the terminals of IGBT power emitter and the auxiliary emitter (u_Ee) has been solved. This is impossible for a conventional detector. On this basis, the adoption of a two-stage operational amplifier can better meet the requirements of high bandwidth measurement under the conditions of a small signal with a large gain. Finally, various experiments have been carried out under the conditions of several typical loads (resistance-inductance load, resistance load and inductance load), different IGBT junction temperatures, soft short-circuits and hard short-circuits for the on-line measurement of IGBT collector current. This is aided by the capacitor voltage which is the integration result of the voltage uEe. The results show that the proposed method of measuring IGBT collector current is feasible and effective.