• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.34 no.4
• /
• pp.251-255
• /
• 2021

a-Si is commonly considered as a primary candidate for the formation of passivation layer in heterojunction (HIT) solar cells. However, there are some problems when using this material such as significant losses due to recombination and parasitic absorption. To reduce these problems, a wide bandgap material is needed. A wide bandgap has a positive influence on effective transmittance, reduction of the parasitic absorption, and prevention of unnecessary epitaxial growth. In this paper, the adoption of a-SiO_x:H as the intrinsic layer was discussed. To increase lifetime and conductivity, oxygen concentration control is crucial because it is correlated with the thickness, bonding defect, interface density (D_it), and band offset. A thick oxygen-rich layer causes the lifetime and the implied open-circuit voltage to drop. Furthermore the thicker the layer gets, the more free hydrogen atoms are etched in thin films, which worsens the passivation quality and the efficiency of solar cells. Previous studies revealed that the lifetime and the implied voltage decreased when the a-SiOx thickness went beyond around 9 nm. In addition to this, oxygen acted as a defect in the intrinsic layer. The D_it increased up to an oxygen rate on the order of 8%. Beyond 8%, the D_it was constant. By controlling the oxygen concentration properly and achieving a thin layer, high-efficiency HIT solar cells can be fabricated.

• Journal of Bio-Environment Control
• /
• v.25 no.4
• /
• pp.249-254
• /
• 2016

This study was carried out to evaluate the efficiency of white shading agent for reduction of greenhouse air temperature and to develop cost-effective cooling strategies for strawberry seedling production during hot seasons. Experiment results showed that solar radiation ($W/m^2$) was reduced by 14~17% and 33~37% for 15% and 35% white wash shading treatments, respectively, in black shading net treatment solar radiation was reduced by 39~44% compared to non-shaded treatment. Measured greenhouse air temperatures in 15% and 35% white wash shading treatments were $38.4^{\circ}C$ and $36.5^{\circ}C$, respectively, whereas in black shading net covered greenhouses air temperature was $35.1^{\circ}C$, thereby 35% and 15% shading treatments showed 3.3 and $1.9^{\circ}C$ higher air temperatures than black net shading treatment. Crown diameter of strawberry plants in black net shading treatment was 7.5mm, and in 15% and 35% white wash shading treatments were 8.6mm and 8.3mm, respectively. Strawberry transplants grown in 35% white wash shading treatment produced the highest above ground fresh weight(7.8g), followed by 15% white wash shading(6.7g) and black net shading treatments(5.8g). Also, both 15% and 35% white wash shading treatments produced higher root fresh weight(4.1g and 4.3g) compare to black net shading treatments(2.7g).

• The Journal of Korean Academy of Prosthodontics
• /
• v.47 no.4
• /
• pp.416-423
• /
• 2009

Statement of problem: The degree of light attenuation at the time of cementation of the PLV restoration depends on characteristics such as thickness, opacity and shade of the restorations, which interfere with light transmittance and, as a result, may decrease the total energy reaching the luting cement. Purpose: The purpose of this study was to compare the degree of conversion of light-cured resin cements measuring by FT-IR in regard to different thickness, light devices and curing time. Material and methods: In the control group, a clear slide glass (1.0 mm) was positioned between the light cured resin cement and light source. The specimens of ceramics were made with IPS Empress Esthetic. The ceramics were fabricated with varying thicknesses-0.5, 1.0, 1.5 mm with shade ETC1. Rely $X^{TM}$ Veneer with shade A3, light-cured resin cement, was used. Light-activation was conducted through the ceramic using a quartz tungsten halogen curing unit, a light emitting diode curing unit and a plasma arc curing unit. The degree of conversion of the light-cured resin cement was evaluated using FT-IR and OMNIC. One-way ANOVA and Tukey HSD test were used for statistical analysis ($\alpha$< .05). Results: The degree of conversion (DC) of photopolymerization using QTH and LED was higher than results of using PAC in the control group. After polymerization using QTH and LED, the DC results from the different ceramic thickness- 0.5 mm, 1.0 mm, 1.5 mm- did not show a significant difference when compared with those of control group. However, the DC for polymerization using PAC in the 1.5mm ceramic group showed significantly lower DC than those of the control group and 0.5 mm ceramic group (P<.05). At 80s and 160s, the DC of light-cured resin cement beneath 1.0 mm ceramic using LED was significantly higher than at 20s (P<.05). Conclusion: Within the limitation of this study, when adhering PLV to porcelain with a thickness between 0.5-1.5 mm, the use of PAC curing units were not considered however, light cured resin cements were effective when cured for over 40 seconds with QTH or LED curing units. Also, when curing the light cured resin cements with LED, the degree of polymerization was not proportional with the curing time. Curing exceeding a certain curing time, did not significantly affect the degree of polymerization.