• Geomechanics and Engineering
• /
• v.4 no.1
• /
• pp.19-37
• /
• 2012

This paper presents the results of analytical and numerical analyses of the effects of performing a pressuremeter test or driving a pile in clay. The geometry of the problem has been simplified by the assumptions of plane strain and axial symmetry. Pressuremeter testing or installation of driven piles has been modelled as an undrained expansion of a cylindrical cavity. Stresses, pore water pressures, and deformations are found by assuming that the clay behaves like normally consolidated modified Cam clay. Closed-form solutions are obtained which allow the determination of the principal effective stresses and the strains around the cavity. The analysis which indicates that the intermediate principal stress at critical state is not equal to the mean of the other two principal stresses, except when the clay is initially isotropically consolidated, also permits finding the limit expansion and excess pore water pressures by means of the Almansi finite strain approach. Results are compared with published data which were determined using finite element and finite difference methods.

• Journal of the Korean Society of Safety
• /
• v.11 no.2
• /
• pp.3-8
• /
• 1996

Fatigue fracture is the cyclic fracture phenomena at a very small local area near a crack tip. Therefore, the detailed quantitative experimental analysis about local cyclic strain distribution near a crack tip is prerequisite In order to make an effective parameter able to account for fatigue fracture problems. However, there are few reports on detailed quantitative experimental analysis of a local cyclic strain distribution near a crack tip, because of experimental difficulties. In this study, the distribution of local fatigue strains near a fatigue crack tip was in detail studied using by fine dot grid strain measurement method. From these results, a single parameter, which characterizes local fatigue strain field, was proposed. In addition, this parameter was applied to evaluate the fatigue crack propagation rate.

• Journal of the Korean Society of Safety
• /
• v.10 no.3
• /
• pp.3-10
• /
• 1995

For most engineering materials are influenced by the dominant mechanism resisting crack extention under large scale yielding conditions. Continuum mechanics analysis shows that fracture toughness, in addition to depending on young's modulus, flow stress strain hardening exponent, and yield strain, should be nearly proportoinal to the effective fracture ductility obtained for the stress state characteristic for region ahead of the crack; plane stress or plane strain. It's known that, in most ductile materials, crack propagation of the material strongly governed by the $J_{IC}$ value, which is still difficult to determine for it's complicate and treble-some determinative process. This paper, on the assumption that, initiation of crack tip strain field reaches on the relationships between the critical value of J-integral ($J_{IC}$) and the local fracture strain(${\varepsilon}_c$) in uniaxial tensile test in the region of maximun reduction areas was described.

• Structural Engineering and Mechanics
• /
• v.86 no.3
• /
• pp.311-324
• /
• 2023

Herein, we present effective polygonal finite elements to which the strain-smoothed element (SSE) method is applied. Recently, the SSE method has been developed for conventional triangular and quadrilateral finite elements; furthermore, it has been shown to improve the performance of finite elements. Polygonal elements enable various applications through flexible mesh handling; however, further development is still required to use them more effectively in engineering practice. In this study, piecewise linear shape functions are adopted, the SSE method is applied through the triangulation of polygonal elements, and a smoothed strain field is constructed within the element. The strain-smoothed polygonal elements pass basic tests and show improved convergence behaviors in various numerical problems.

• Korean Journal of Materials Research
• /
• v.28 no.8
• /
• pp.435-439
• /
• 2018

MA Al alloys are examined to determine the effects of alloying of Mg and Cu and rolling on tensile deformation behavior at 748 K over a wide strain rate range($10^{-4}-10^3/s$). A powder metallurgy aluminum alloy produced from mechanically alloyed pure Al powder exhibits only a small elongation-to-failure(${\varepsilon}_f$ < ~50%) in high temperature(748 K) tensile deformation at high strain rates(${\acute{\varepsilon}}=1-10^2/s$). ${\varepsilon}_f$ in MA Al-0.5~4.0Mg alloys increases slightly with Mg content(${\varepsilon}_f={\sim}140%$ at 4 mass%). Combined addition of Mg and Cu(MA Al-1.5%Mg-4.0%Cu) is very effective for the occurrence of superplasticity(${\varepsilon}_f$ > 500%). Warm-rolling(at 393-492 K) tends to raise ${\varepsilon}_f$. Lowering the rolling-temperature is effective for increasing the ductility. The effect is rather weak in MA pure Al and MA Al-Mg alloys, but much larger in the MA Al-1.5%Mg-4.0%Cu alloy. Additions of Mg and Cu and warm-rolling of the alloy cause a remarkable reduction in the logarithm of the peak flow stress at low strain rates (${\acute{\varepsilon}}$< ~1/s) and sharpening of microstructure and smoothening of grain boundaries. Additions of Mg and Cu make the strain rate sensitivity(the m value) larger at high strain rates, and the warm-rolling may make the grain boundary sliding easier with less cavitation. Grain boundary facets are observed on the fracture surface when ${\varepsilon}_f$ is large, indicating the operation of grain boundary sliding to a large extent during superplastic deformation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.8
• /
• pp.643-650
• /
• 2000

Density-of-states effective mass(m*$_{d}$) and conductivity mass(m*$_{c}$)for Ge and Ge$_{0.8}$/Sn$_{0.2}$ are obtained by using 8$\times$8 k.p and strain Hamiltonians. It is shown that m*$_{d}$ and m*$_{c}$ for electrons in Ge/Ge$_{0.8}$/Sn$_{0.2}$(001) and Ge$_{0.8}$/Sn$_{0.2}$/Ge(001) are much smaller than those for electrons in relaxed Ge mainly due to the increase of interaction caused by the strain between the conduction band and valence bands at the $\Gamma$ point. The lift of degeneracy in Ge/Ge$_{0.8}$/Sn$_{0.2}$(001) and Ge/Ge$_{0.8}$/Sn$_{0.2}$(001) makes m*$_{d}$ and m*$_{c}$ for holes smaller than those in relaxed Ge and results in the decrease of the interband scattering as well as interband scattering. The decrease of the interband scattering is more obvious in Ge/Ge$_{0.8}$/Sn$_{0.2}$(001) because of its large splitting energy between the heavy hole and light hole band. Therefore, Ge/Ge$_{0.8}$/Sn$_{0.2}$(001) is expected to be good candidate for the development of ultra high-speed CMOS device.CMOS device.eed CMOS device.CMOS device.

• Korean Journal of Veterinary Research
• /
• v.51 no.3
• /
• pp.193-201
• /
• 2011

An attenuated vaccine strain AVR1/08 of Korean respiratory type of infectious bronchitis virus (IBV) was developed by 89th passages of IBV D85/06 strain in chicken eggs. The AVR1/08 strain had higher virus titer at least 20 times ($10^{1.3}$) than the parent virus D85/06 by egg inoculation method. The AVR1/08 strain had a single point mutation (S to Y) at position 56 of spike protein of IBV compared to parent virus IBV D85/06 strain. The mutation was observed consistently at viruses after 47th passage in chicken eggs. The AVR1/08 strain showed no virulence even after 6 passages in chickens and all chickens inoculated induced anti-IBV antibody 14 days after vaccination. The AVR1/08 strain had broad protective efficacy against QX type Korean nephropathogenic virus (Q43/06 strain), KM91 type Korean nephropathogenic virus (KM91 strain) and Korean respiratory virus (D85/06 strain). In contrast, Massachusetts (Mass) type attenuated vaccine strain H120 showed protection of 37.5 to 50% against these three viruses. Our results indicate that the AVR1/08 strain has potential as an attenuated vaccine effective in controlling IBVs circulating in Korea.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.14 no.3
• /
• pp.39-48
• /
• 2010

Improved seismic performances of RC bridges can be attained by sufficient ductilities of piers, which can be obtained by providing sufficient lateral confinements to the plastic hinge regions of piers. The cross sectional shape and the amount of lateral reinforcements are key parameters in the determination of effective confinements. Even though identical amounts of lateral reinforcement are provided, the effective confinement differs due to different spacing, arrangements, hook details and so on. Unlike circular sections in which confinement is exerted by mere hoop reinforcements, cross-ties are arranged in square or rectangular sections to enhance the effective confinements. The stress-strain relationship of confined concrete is varied by how to consider these cross-ties. In this study, the stress-strain relationships of confined concrete with cross-ties are investigated experimentally and their mechanical characteristics are estimated by comparison with other empirical equations.

• Journal of Chest Surgery
• /
• v.32 no.11
• /
• pp.984-988
• /
• 1999

Background: Donor-specific blood transfusion(DSBT) before organ transplantation has been demonstrated to prolong allograft survival; the mechanism of this effect has remained unclear. Only a few researches have been performed on this subject in our country. Material and Method: To investigate the effect of DSBT, we selected 5 donor recipient combinations using rats of pure strain such as PVG, ACI, and LEW. One ml of donor whole blood was transfused to each recipient through the femoral vein 7 days prior to transplantation. The donor heart was transplanted to the recipient's abdominal vessels heterotopically using modified Ono and Lindsey's microsurgical technique. Five transplantations were done for each combination. Postoperatively, donor heart beat was palpated everyday through the recipent's abdominal wall. Rejection was defined as complete cessation of donor heart beat. Result: The allogeneic heart grafts transplanted from PVG strain to ACI strain(PVG ACI) without DSBT were acutely rejected(mean survival 10.2 days). With pretransplant DSBT, the cardiac allografts in PVG ACI and LEW PVG combinations survived indefinitely(more than 100 days), those in ACI PVG combination survived 12 to 66 days(mean 31.8 days), those in PVG LEW survived 8 to 11 days(mean 10.0 days), and those in ACI LEW survived 7 to 9 days(mean 8.0 days). In brief, DSBT prior to heart transplantation was definitely effective in PVG ACI and LEW PVG combinations and moderately effective in ACI PVG combination, but not effective in PVG LEW and ACI LEW combinations. Conclusion: DSBT prior to heart transplantation showed variable effects, but might prolong cardiac allograft survival indefinitely in some donor recipient strain combinations. The mechanism of this effect should be further investigated.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.15 no.5
• /
• pp.101-112
• /
• 2011

This paper shows a study carried out on the estimation of nominal flexural strength for CFRP-plated RC beams failed by intermediate crack debonding. A strength reduction factor is proposed to consider the effect of the intermediate crack debonding for the determination of nominal flexural strength. The proposed factor is derived from experimental data and utilizes the ratio of effective stress(or strain) in the CFRP plate to its ultimate strength(or strain) which is called effective strain model. An analytical equation for the estimation of the nominal flexural strength is formulated as a function of strength reduction factor. The validity, accuracy and efficiency of the proposed factor are established by comparing the analytical results with the experimental data, and the major design codes, as well as a number of factors given by researchers. The analytical results presented in this paper indicate that the proposed factor can effectively estimate the flexural nominal strength of CFRP-plated reinforced concrete beams failed by intermediate crack debonding.