• 지식정보인프라
• /
• 통권7호
• /
• pp.134-140
• /
• 2001

To know about the performance of KREONET, we installed an active network performance measurement tool, PingER. For customization, we modified its architecture and some codes. Although this customization is a minor change of PingER, it gives much benefit and convenience for both operators and users. Using PingER, we can measure the effect of the STAR TAP link. The new networking through the link is a little bit slower than the previous networking. But the new link shows far fewer packet losses and provides more reliable networking.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
• /
• pp.613-617
• /
• 2000

This paper descries the effect of the stylus tip size on the measuring error in surface topography measurement. To analyze the distortional effect of an actual surface geometry originating from the finite stylus size, the surface is modeled as a sinusoid and the stylus tip as a circle. the measuring error is defined as the ratio of the standard deviation of a tracing profile and an original profile. It is shown that this measuring error depends on the amplitude and wavelength of an original profile. In this paper, the spectrum analysis is applied to investigate the distortional effect due to the mechanical filtering of the stylus in the frequency domain. and, the cumulative power spectrum is applied to determinate the minimum wavelength limits to be measured with the various stylus tip radius from these results, a new method to select proper stylus tip radius is proposed.

• 대한기계학회논문집B
• /
• 제27권12호
• /
• pp.1758-1765
• /
• 2003

Monte Carlo simulation(MC) method was used as an uncertainty assessment tool for gas flow measurement in this paper. Uncertainty sources for gas flow measurement were analyzed, and probability distribution characteristics of each source were discussed. Detailed MC methodology was described including the effect of the number of simulation. The uncertainty result was compared with that of the conventional sensitivity coefficient method, and it was revealed that the results were different from each other for this particular gas flow measurement case of which the modelling equation was nonlinear. The MC was comparatively simple, convenient and accurate as an uncertainty assessment method, especially in cases of complex, nonlinear measurement modelling equations. It was noted that the uncertainty assessment method should be selected carefully according to the mathematical characteristics of the measurement.

• 한국공작기계학회논문집
• /
• 제12권4호
• /
• pp.36-42
• /
• 2003

Theodolite measurement system is non-contacted 3-dimensional measurement system. The system accuracy is ${\pm}0.5mm$or better for distance 0~100m. And the system is used for the measurement of a product of middle and large scale. This study is performed for the measurement error factors of the system. We could know that the main measurement error factors are temperature, illumination and skill. Also, we performed the study for the effect according to the height difference of scale bar.

• 한국산학기술학회논문지
• /
• 제12권11호
• /
• pp.4778-4787
• /
• 2011

본 연구의 목적은 서비스산업에서 서비스품질 평가에 자주 사용되었던 KS-SQI모형을 적용하여 IT아웃소싱 서비스품질 평가도구를 개발하는 것이다. 독립변수로 본원적 서비스, 예상외 서비스, 신뢰성, 친절성, 적극지원성, 접근용이성, 물리적 환경을 선정하였고, 이들이 IT아웃소싱 서비스품질 평가도구로서 적합한지를 검증하기 위해 IT아웃소싱 만족도에 영향을 주는지를 분석하고, IT아웃소싱 만족도는 재계약의도에 영향을 주는지를 조사하였다. 가설검증을 위해 LISREL을 활용하여 변수들 간의 경로분석을 실시한 결과, 본원적 서비스, 신뢰성, 친절성, 적극지원성, 접근용이성, 물리적 환경은 IT아웃소싱 만족도에 유의적인 영향을 주었고, 예상외 서비스는 유의적인 영향이 없는 것으로 나타났다. 그리고 IT아웃소싱 만족도는 재계약의도에 유의적인 영향을 주는 것으로 나타났다. 도출된 6개의 측정도구는 IT아웃소싱 서비스품질 평가도구로서 적합함이 입증되었다. 본 연구의 의의는 IT아웃소싱 서비스품질 평가에 KS-SQI모형을 적용한 측정도구를 개발함으로서 이론적인 확장을 이루었고, 실무적인 측면에서는 IT아웃소싱 제공업체와의 재계약을 위한 IT아웃소싱 서비스품질을 평가하는 도구로 활용될 수 있다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2011년도 제42회 하계학술대회
• /
• pp.420-421
• /
• 2011

In generally, the small harmonic current has not influence on the power system because of offset effect. But the bulk harmonic current has not an offset effect, so that influences on the other customer. This paper describes the measurement power quality in the industrial area, and data analysis result. Also this effect has verified by PACAD/EMTDC simulation tool.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 춘계학술대회 논문집
• /
• pp.229-233
• /
• 2003

Theodolite measurement system is non-contacted 3-dimensional measurement system. The system accuracy is 0.5 mm or better for distance 0 ~ 100m. And the system is used for a product of middle and large scale. This study is performed for the measurement uncertainty of the system. We could know that the main uncertainty factors are temperature, illumination and skill. And, we perform the study for the effect according to the height difference of scale bar. And, we calculated the measurement uncertainty with those factors.

• 대한공업교육학회지
• /
• 제32권2호
• /
• pp.171-187
• /
• 2007

이 연구의 목적은 선삭 가공시 발생하는 채터 진동을 계측하기 위하여 일반적인 가속도계가 가진 단점을 보완한 페브리-페롯형(Fabry-Prtot) 광섬유 간섭계 센서를 공구에 직접 부착하여 채터 진동을 측정하고 이것의 유용성을 확인하는 것이다. 측정된 주파수 스펙트럼과 이론해석 상의 리셉턴스 곡선과 비교하였는데 공구진동이 클수록 가진 주파수 이동이 생성되며 이는 공구의 날 끝에 질량효과가 더해짐을 의미함을 알 수 있었다. 질량효과가 더해지면 진동 주파수는 저주파 쪽으로 이동한다. 진동 주파수의 저주파 영역의 이동은 일반적인 재생형 채터에서 흔히 일어나는 현상이다. 또한 측정한 채터 주파수는 고유진동수가 아닌 외부 가진 주파수인 것으로 확인 됐으며 측정 결과와 같이 본 실험에 사용된 광섬유 센서는 외부 진동 주파수를 잘 계측 하였으며 페브리-페롯 센서는 특히 공구진동의 측정에 유용함을 보았다. 본 연구를 통하여 적용분야로 간섭계형 광섬유 센서를 공구 표면에 직접 설치하고 공구 진동을 관찰하는 교육목적의 실험에도 응용할 수 있다. 본 실험과 같은 페브리-페롯 간섭계 센서의 공구 직접 접촉식 방법에 대한 연구는 국내외 적으로 그 사례를 찾아보기 힘든 독창적인 방법인 것으로 추정된다. 본 연구결과는 또한 향후 공구진동과 마멸을 연구하는데 기초 자료로 활용할 수 있을 것으로 판단된다.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 추계학술대회
• /
• pp.396-400
• /
• 2003

This paper has studied thermal characteristics of machine tool to develope high speed spindle and optimum design condidering the thermal deformation. Comparing the test data of temperature measurement and structural analysis data using FEM, we verifiedthe test validity and predicted thermal deformation, influence of spindle generation of heat, and established cooling system to prevent the thermal deformation. 1) The temperature rise of spindle system depends on increasing number of rotation and shows sudden doubling increment of number of rotation over 7,000rpm. 2) Oil jacket cooling can be effective cooling method below 8,000rpm but, over 8,000rpm, it shows the decrement of cooling effect. 3) Comparing FEM analysis results and revolution test results, we can confirmn approximate temperature change consequently, it is possible to simulate temperature rise and thermal distribution on the inside of spindle system. 4) We can confirm that simulated approach by FEM analysis can be effective method in thermal-appropriate design..

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 추계학술대회 논문집
• /
• pp.498-503
• /
• 2002

This paper has studied thermal characteristics of machine tool to develope high speed spindle and optimum design considering the thermal deformation. Comparing the test data of temperature measurement and structural analysis data using FEM, we verified the test validity and predicted thermal deformation, influence of spindle generation of heat, and established cooling system to prevent the thermal deformation. 1) The temperature rise of spindle system depends on increasing number of rotation and shows sudden doubling increment of number of rotation over 7,000rpm. 2) Oil jacket cooling can be effective cooling method below 8,000rpm but, over 8,000rpm, it shows the decrement of cooling effect. 3) Comparing FEM analysis results and revolution test results, we can confirmn approximate temperature change consequently, it is possible to simulate temperature rise and thermal distribution on the inside of spindle system. 4) We can confirm that simulated approach by FEM analysis can be effective mettled in thermal-appropriate design.