• Korean Journal of Environment and Ecology
• /
• v.19 no.3
• /
• pp.258-268
• /
• 2005

The objective of this study was to monitor the edge vegetation development process after timber harvesting at deciduous hardwood forest in Seoul National University Research Forest of Baekwoonsan (Mt), Korea The results from the 4th (2001) and 5th (2003) survey for edge vegetation development process after timber harvesting are summarized as follows. The competitive species at the harvested forest edge are Lindera erythrocarpa, Weigela subsessilis, Lespedeza maximowiczii, Lindera obtusiioba, Arajia eiata. There were Lindera erythrocarpa, Ivelgela subsessilis, Staphyiea bumaida as competitive species at harvested forest border between harvested forest edge and harvested interior. And at the forest interior, the competitive species were Lindera erythrocarpa, Lindera obtusiloba. There were differences in the competitive species at the forest edge due to the differences in direction, altitude, and existing dominant species. But Lindera erythrocarpa, Weigela subsessilis were appeared to be a competitive specieg at the southwestern slope (A site) and northeastern slope (B site). After timber harvesting, Sasa borealisshowed a good growth in early days, but showed a tendency of declining with the developing of canopy layer And coverage was generally higher at the Northeastern slope (Site B) than southwestern slop (Site A). The similarity index was lower as the distance from the forest edge becomes farther.

• Korean Journal of Mineralogy and Petrology
• /
• v.34 no.2
• /
• pp.121-131
• /
• 2021

Magnesium (Mg) present in carbonate minerals as impurities has been used as a geochemical proxy to infer the environmental conditions where the minerals precipitated. The reliability of Mg geochemical proxies requires fundamental understanding of Mg incorporation into minerals based on accurate speciation of Mg ²⁺ in the crystal structure, which is determined mainly by application of X-ray absorption spectroscopy (XAS). However, high uncertainties are involved in interpreting the XAS spectra of minerals containing trace amount of Mg ²⁺. Because density function theory (DFT) can predict an XAS spectrum for a crystal structure, DFT calculations can reduce the uncertainties in the interpretation of the XAS spectrum. In this study, we calculated ab initio Mg K-edge absorption spectra of Mg silicates and (hydr)oxides based on DFT and analyzed the correlation between the calculated spectra and Mg structural parameters. Our ab initio Mg K-edge absorption spectra well reproduced the key features of the experimental spectra. The absorption-edge positions of the calculated spectra showed the weak positive correlation with the average Mg-O bond distance or Mg effective coordination number. The current study shows that DFT-based core-level spectroscopy method is a powerful tool in providing standard Mg K-edge spectra of diverse Mg minerals and determining the Mg chemical species within carbonate minerals.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.21 no.2
• /
• pp.105-111
• /
• 2005

It is essential to establish the suitable position for artificial maxillary anterior teeth, because of not only esthetics, phonetics, mastication, but also optimal position of artificial posterior teeth for the construction of functional and esthetic prostheses. Anatomic landmarks have been used in the arrangement of artificial teeth. Such as incisive papilla and palatal rugae are useful landmarks for positioning occlusal rim and upper anterior artificial teeth because they are relatively stable and to be identified on master cast. Therefore, if average distance between maxillary anterior teeth and landmarks in dentate subjects are measured and applied, appropriate position of occlusal rim can be initially established. In this study, to present a guide to the position of the occlusal rim for upper anterior teeth of edentulous patients, horizontal distance between anatomic landmarks were measured. Maxillary casts were made in 72 Korean dentate subjects. Horizontal distance between central incisor and incisive papilla, between incisive papilla and intercanine line, and between primary palatine rugae and gingival margin of canine were measured on each cast. The results of this study were as follows ; 1. The mean distance from the incisal edge of central incisor to the posterior border of incisive papilla was 12.1 mm (Male 12.2 mm, Female 11.9 mm). 2. The mean distance between posterior border of incisive papilla and intercanine line was 3.5 mm (Male 3.4 mm, Female 3.6 mm / Left 3.6 mm, Right 3.4 mm). 3. The mean distance from the palatal gingival margin of canine to the lateral border of primary palatine rugae was 2.4 mm (Male 2.4 mm, Female 2.4 mm / Left 2.4 mm, Right 2.3 mm). 4. On all measured items, there were no significant differencies in measured values between male and female, and between left and right sides. (P>0.05).

• Journal of Korea Foundry Society
• /
• v.3 no.1
• /
• pp.13-21
• /
• 1983

In order to determine the feeding distance of aluminiun alloys (Alsi7Mg and AlCu4Ti) bar castings in the sand mold, the distance of the sound castings has been observed by radiograph for various risers, melt treatment, and casting design. Variation of porosity and hardness with the distance from the riser were also measured in order to determine the casting soundness. The results obained were as follows; 1) The modulus of riser should be 1.4 times of the casting`s 2) The maximum distance which can be made sound is greatly dependent on chemical composition and ingate location, and follows the rules given by the formula; a) When the melt flows into the casting first, and the riser afterward, D = 37.7 ${\sqrt{T}}$ for AlSi7Mg D = 31.2 ${\sqrt{T}}$ for pure aluminium D ${\ge}$ 54.8 ${\sqrt{T}}$ for AlCu4Ti Where T = casting thickness in mm Of this maximum distance, $aa{\sqrt{T}}$ for AlSi7Mg and 7.5 ${\sqrt{T}}$ for pure aluminium is made sound by the chilling effect of the casting edge. b) When the melt flows into the casting passing through the riser, $30{\times}30{\times}600mm$ bars can be made sound in all cases 3) Percentage of porosity is higer in AlCu4Ti than AlSi7Mg. And it is increased gradually by moving closer to the riser in case of $30{\times}30{\times}600mm$ bars, but for the $30{\times}30{\times}600mm$ bars it is increased gradually by moving closer to the center of bars. 4) Hardness variation is similar to the tendency of porosity. And it decreased gradually with approaching to the center in case of $30{\times}30{\times}600mm$ bars.

• The Korean Journal of Quaternary Research
• /
• v.17 no.2
• /
• pp.129-133
• /
• 2003

Water is critically important for Tricholoma matsutake(Tm) growth because it is the major component of the mushroom by over 90%. The mushroom absorbs water through the below ground hyphal colony. Therefore, the objectives of our study were to investigate spatio-temporal water changes in Tm colonies. This study was carried out at Tm fruiting sites in Sogni Mt National Park, where the below-ground mushroom colonies have been irrigated. To identify spatial water status within the Tm soil colony soil moisture and ergosterol content were measured at six positions including a mushroom fruiting position on the line of the colony radius. To investigate temporal soil moisture changes in the soil colony, Time Domain Reflectometry(TDR) sensors were established at the non-colony and colony front edge, and water data were recorded with CR10X data logger from late August to late October. Before irrigation, whereas it was 12.8% at non-colony, the soil water content within Tm colony was 8.0% at 0-5cm from the colony front edge, 6.2% at 10-15cm and 6.5-7.5% at 20-40cm. And the content was 12.1% at 80cm distance from the colony edge, which is similar to that at the non-colony. In contrast, ergosterol content which is proportional to the live hyphal biomass was only 0.4${\mu}g$/g fresh soil at the uncolonized soil, while 4.9 $\mu\textrm{g}$/g fresh soil at the front edge where the hyphae actively grow, and 3.8 ${\mu}g$/g fresh soil at the fruiting position, l.1${\mu}g$/g at 20cm distance and 0.4${\mu}g$/g in the 40cm rear area. Generally, in the Tm fungal colony the water content changes were reversed to the ergosterol content changes. While the site was watered during August to October, the soil water contents were 13.5∼23.0% within the fungal colony, whereas it was 14.5∼26.0% at the non-colony. That is, soil water content in the colony was lower by 1.0∼3.0% than that in the non-colonized soil. Our results show that Tm colony consumes more soil water than other parts. Especially the front 30cm within the hyphal colony parts is more critical for soil water absorption.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.41 no.5
• /
• pp.9-18
• /
• 2004

This paper presents a vehicle detecting algorithm using microwave system signals. The Proposed algerian decides the breakpoint of signals using the likelihood criteria. The decided signals are segmented and simplified. The proposed searching algorithm uses the Euclid distance from the weighted signal data. We tested the proposed algorithm to compare with the segmentation which is a method using smoothing and edge detection. We confirm that the proposed algorithm is very useful for detecting vehicles by field test.

• Proceedings of the Korean Information Science Society Conference
• /
• 2006.10c
• /
• pp.83-87
• /
• 2006

Similarity search in moving object trajectories is an active area of research. In this paper, we introduce a new concept of measure that computes spatial distance (similarity) between two trajectories of moving objects on road networks. In addition, we propose an algorithm that generates a sequence of matching edge pairs for two trajectories that ate to be compared and computes spatial distance between them which is non Euclidian in nature. With an example, we explain how our algorithm works to show spatial similarity between trajectories of moving objects in spatial network.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.73.4-73
• /
• 2001

We suggest a system to detection whether material picked up is double or single when the robot feeds them in automation line. This system measures thickness of metal plate and alarms when they are double sheet measuring boundary lines of metal sheet. This system calculates the minimum distance of straight boundary lines by eliminating noise in the edge regions. In the experimental system, double or single is determined by calculating implemented the thickness in the image where the distance of pixels are retrieved by the hash table. In this paper, the algorithm of histogram is adapted to experiment in the implement, thus proved as double sheet detection system.

• 한국가시화정보학회:학술대회논문집
• /
• 2001.12a
• /
• pp.53-61
• /
• 2001

Highly swept leading edge extensions(LEX) applied to delta wings have greatly improved the subsonic maneuverability of contemporary fighters. Fundamental approach by PIV method was adopted to study the basic flow of the vortex pair formation appearing on a delta wing model with or without LEX. Three angles of attacks$(16^{\circ},\;24^{\circ},\;28^{\circ})$ and four measuring section of chord length(LEX-on) and three section(LEX-off) were selected as experimental conditions. From the PIV analysis, maximum vorticity was found at a given chord length and maximum velocity was also detected at larger chord length where stronger vortex was generated. Furthermore, the effect of LEX was remarkable at the vortex pair distance indicating narrower distance at LEX-on case.

• Proceedings of the KIEE Conference
• /
• 2007.04a
• /
• pp.32-34
• /
• 2007

The X-ray projection system has long been used for steel-tube inspection and weld monitoring. The thickness of tubes and welded areas is based on the evaluation of radiographic shadow projections. The traditional tangential measurement estimates the distance of border lines of the projected wall shadows of a tube onto a radiographic image detector. The detected image in which although there is a variety of noise may be sectioned into several partitions according to its specific blocks. Imaging noise originates from most of elements of the system, such as shielding CCD camera, imaging screen, X-ray source, inspected object, electronic circuits and etc. The tangential projection incorrectness and noise influence on imaging quality. In this paper we first sectionalize the X-ray image on the basis of vertical contrast difference. And next functional and statistic analysis are carried on at each region. Geometrical distance and unsharpness of the edge caused by visual evaluation uncertainties are also discussed.