• 비파괴검사학회지
• /
• 제11권1호
• /
• pp.7-12
• /
• 1991

The multi-frequency eddy current technique has been used for evaluation of various type of defects in tubings. However, this technique is not sufficient to detect and evaluate the defect in tubings if the defect is located in the geometrically complicated area(e. g. tube support plate, anti-vibration bar, tubesheet area) and mixing residue signal is significant to the defect signal. In order to improve the reliability of the multi-frequency eddy current technique, the effect of the interaction of mixing residue after frequency mixing with a function of distances between the defect and the tube support plate boundary has been analyzed theoretically. The experimental results have been discussed with the theoretical developments. The calculation shows the interaction between the two neighboring signal sources could be significant within the range of approximately 1.0mm with the experimental condition.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 춘계학술대회논문집
• /
• pp.172-177
• /
• 2001

This paper proposes an adaptive feedforward controller (AFC) based on LMS for periodic disturbance rejection in active magnetic bearing system. The proposed controller does not alter the stability and robustness of the existing AMB system. It is shown that the control delay due to the eddy current as well as runout and unbalance can be identified and compensated using the estimated displacement from the measured magnetic flux. The simulation results confirm that the proposed scheme successfully identifies and compensates for the runout, unbalance and eddy current effect, leading to a high-precision magnetic bearing system.

• 비파괴검사학회지
• /
• 제9권2호
• /
• pp.37-41
• /
• 1989

The purpose of this paper is to estimate the effect of wobble and nonconcentricity of tubes or rods in eddy current test with encircling test coils. Because the eddy current induced in a sample is related to the total magnetic flux linkages, the information about magnetic field distribution in a coil is important. In theoretical study, magnetic field distribution in a single turn coil was calculated and variation of impedance according to the difference of sample positions was presumed. Magnetic field intensity at inside of a solenoidal coil was measured and compared with the theoretical estimation. In experiment, impedance loci of a coil encircling an aluminum rod were measured at different sample positions. The effect of crack positions was examined at same sample positons.

• 비파괴검사학회지
• /
• 제4권2호
• /
• pp.7-14
• /
• 1985

An experiment to investigate the rate of change of phase angle of eddy current output signal caused by outer surface defect of nonferromagnetic tube by variation of standard depth of penetration and variation of percent of tube wall penetration was carried out. The results of the experiment show that the phase angle of defect signal is increased with decreasing the standard depth of penetration or the depth of defect. The results also show that the phase angle is decreased with increasing the skin effect of eddy current, and that the resolution is decreased with decreasing the depth of defect.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1998년도 추계학술대회
• /
• pp.92-93
• /
• 1998

In this study, we have established the technique to estimate the gradient waveforms distorted by the eddy current in MRI. After obtaining the eddy current effect transfer function using the finite element method, we have used the transfer function to estimate the output gradient waveforms at any points inside the imaging region. We also present experimental results to be compared with estimated ones.

• 한국전기전자재료학회논문지
• /
• 제15권9호
• /
• pp.822-829
• /
• 2002

This paper deals with the distribution characteristics of the current density and axial magnetic flux density for each slits made on the contact electrode in the vacuum interrupter with axial magnetic field type using 3-dimension finite element analysis. It has been known that the presence of an axial magnetic field parallel to the current flow in the arc plasma can increase the high current breaking capacity of vacuum interrupter by carrying out the arc plasma from constricted mode to diffusion mode. The axial magnetic field is created of itself by current flow in the segments of coil electrode behind the contact electrode. The analyzed results show that if the slits are made in the contact electrode, they can increase the current density and axial magnetic flux density in the contact electrode surface and at the gap distance, which is due to decrease the effect of eddy currents flowing in the contact electrode. The phase shift due to eddy currents, defined 3s time difference between the maximum value of current and axial magnetic field, is decreased still more by increasing the number of slits made in the contact electrode at the center point of gap distance. These results demonstrate that 3-dimension finite element analysis has a great deal of merits in the development and evaluation of new electrode at the design of vacuum interrupter.

• Journal of Magnetics
• /
• 제20권3호
• /
• pp.273-283
• /
• 2015

In this study, we propose an analytical model for studying magnetic fields in radial-flux permanent-magnet eddy-current couplings by considering the effects of slots and iron-core protrusions on the eddy currents. We focus on the analytical prediction of the air-gap field by considering the influence of eddy currents induced in conducting bars. In the proposed model, the permanent magnet region is treated as the source of a time-varying magnetic field and the moving-conductor eddy current problem is solved based on the resolution of time-harmonic Helmholtz equations. The spatial harmonics in the air gap and in slots, as well as the time harmonics are all considered in the analytical calculation. Based on the proposed field model, the electromagnetic torque is computed by using the Maxwell stress tensor method. Nonlinear finite element analysis is performed to validate the analytical model. The proposed model can be used for permanent-magnet eddy-current couplings with any slot-pole combination.

• Progress in Superconductivity
• /
• 제12권2호
• /
• pp.93-98
• /
• 2011

Pinning force is the mechanism between a superconductor and a permanent magnet and it provides a stable levitation. However, when external force greater than the pinning force such as the earthquake exerts, the levitated object may lose the levitating characteristic. In order to achieve more stabilized levitation, the copper plate was inserted in between a superconductor and permanent magnets. And by applying the eddy current effect caused from the relationship between a copper plate and permanent magnets, more stabilized levitation can be established. In this study, an optimized design was found based on various configurations of permanent magnet's polarity, thickness and area of copper plate, and the gap distance between copper plate and permanent magnet. As results, higher eddy current value was obtained at where the change of polarity exists in permanent magnet configuration, and the highest eddy current value was observed at the copper plate thickness of 5 mm and the area of 80 mm ${\times}$ 80 mm. From the resulted optimized conditions above, which are 7 mm gap distance between a superconductor and permanent magnets and 80 mm ${\times}$ 80 mm ${\times}$ 5 mm dimension of a copper plate, the stiffness value was 65 % increased comparing to without any copper plate insertion.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 A
• /
• pp.198-200
• /
• 1997

This paper consider a simple Nondestructive Testing(NDT) having eddy currnt effect. We analyzed the two dimension modeling of alternative magnetic field. eddy current with voltage source. And, the current magnitude and phase data obtained from each different frequency five object position is used for learning the neural network. Therefore, we can recognize an object position pattern from new input current magnitude, phase data.

• 대한기계학회논문집
• /
• 제18권3호
• /
• pp.529-539
• /
• 1994

In laser heat treatment process of steels, the thin layer of substrate is rapidly heated to the austenitizing temperature and subsequently cooled at a very fast rate due to the self-quenching effect. Consequently, it is transformed to martensitic structure which has low magnetic permeability. This observation facilitates the use of a sensor measuring the change of electromagnetic field induced by the hardening layer. In this paper, the eddy-current electromagnetic field is analyzed by a finite element method. The purpose of this analysis is to investigate how the electrical impedance of the sensor's sensing coil varies with the change in permeability. To achieve this, a numerical model is formulated, taking into consideration the hardening depth, distance of the sensor from the hardened surface and the frequency driving the sensor. The results obtained by numerical simulation show that the eddy-current measurement method can feasibly be used to measure the changing hardening depth within the frequency range from 10 kHz to 50 kHz.