• Journal of Adhesion and Interface
• /
• v.9 no.1
• /
• pp.9-15
• /
• 2008

EVA foam was treated by oxygen plasma under a various treatment time for surface modification. The effect of plasma treatment on surface properties of EVA foam was investigated in terms of FT-IR ATR, XPS, contact angle, and SEM analysis and the adhesion characteristic of the EVA foam was studied in peel strength. As a results, EVA foam treated by plasma led to an elimination of organic compound, an increase of oxygen content, and an increase of surface roughness, resulting in improving the adhesion properties of the EVA foam. As the plasma treatment time increased, the hydrophilicity and physical change of surface of the EVA foam were increased and showed maximum value at 180 s and 420 s, respectively. The maximum adhesion strength appeared at plasma treatment time of 420 s and therefore, in this study the physical change was thought to be a major factor for improving the adhesion of the EVA foam.

• Journal of Adhesion and Interface
• /
• v.2 no.3
• /
• pp.9-15
• /
• 2001

To estimate the effect of the surface state of the EVA foam on an adhesion, the surface was treated with solvents having different values of a solubility parameter and a surface tension. The morphology and the contact angle were measured by SEM and contact angle tester, respectively. The value of the critical surface tension(${\gamma}_{c,0}$) of the EVA foam calculated by Zismann plot was 27.08 dyne/cm. The surface state and the ${\gamma}_c$ of the EVA foam were changed by solvent treatment. The swelling ratio of EVA foam was influenced by solubility parameter of a solvent, on the other hand the degree of change in the surface state was dependent on a surface tension of a solvent. When a surface tension of solvent. When a surface tension of solvent is lower than ${\gamma}_{c,0}$ of the EVA foam, the wettability of a solvent was good and the surface state was greatly changed. The adhesion strength of EVA foam was greatly improved to above 600% as compared to that of the untreated one. As the ${\gamma}_c$ of EVA was closed to the surface tension of the primer, the good adhesion strength was obtained.

• Elastomers and Composites
• /
• v.36 no.1
• /
• pp.14-21
• /
• 2001

To increase the properties of EVA foam such as tensile strength, rebound resilience, and compression set, ethylene-1-butene copolymer (EtBC) was blended with EVA. After that crosslink characteristics of the blends and cell structures and mechanical properties of the foam were studied. As the amount of EtBC increased in EVA/EtBC blends, torque values of oscillating disc rheometer(ODR) increased and the foaming ratio decreased because the viscosity and crosslink density of EVA/EtBC blends increased. Foaming ratio and cell size of the foam increased by increasing the amount of foaming agent. When compared the mechanical properties of the foam which have same densities, tensile strength, rebound resilience, and compression set properties of the foam were improved by increasing the amount of EtBC in the EVA/EtBC blends.

• Textile Coloration and Finishing
• /
• v.30 no.2
• /
• pp.107-116
• /
• 2018

Simplification of the manufacturing process in shoe making is essential to improve productivity and reduce production costs. To improve the adhesion of EVA foam used as a midsole, EVA/itaconated EPDM(EPDM-g-IA)(80/20wt%) blend was prepared using Torque Rheometer-Plasti-Corder, and 1,6-hexamethylenediamine/crosslinking agent/foaming agent/additive were mixed, followed by amidation reaction and foaming to prepare EVA/EPDM-g-IA foam for shoe midsole. In this study, we investigate the effect of the content of 1,6-hexamethylenediamine(0, 0.5, 1.0, 2.0, 3.0) on the mechanical properties, water-contact angle and adhesion of EVA/itaconated EPDM foam. As the content of 1,6-hexamethylenediamine increased, mechanical properties such as tensile strength, tear strength, tensile elastic modulus, hardness, and water-contact angle were lowered, but elongation at break and compression set(%) were increased. Both normal type and non-UV type adhesive strength increased with increasing diamine content. In particular, it was found that the adhesion strength of the non-UV type adhesion increased sharply with increasing diamine content. As a result, an adherend rupture occurs in a foam sample having a content of 1,6-hexamethylenediamine of 3phr. From this, it can be seen that the EVA/itaconated EPDM foam for shoe midsoles, which can be used for non-UV adhesion without primer and UV treatments, have been developed.

• Fashion & Textile Research Journal
• /
• v.24 no.1
• /
• pp.127-137
• /
• 2022

Recently, various clothing items are being developed using 3D printing technology, but comfort has become an issue while wearing them for a long time. Therefore, this study researched on how the temperature and humidity of the devices developed by 3D printing change depending on the material combination. Five types of material combinations (EVA foam, TPU density 10%, TPU density 30%, EVA foam+TPU density 10%, and EVA foam+TPU density 30%) were selected as variables, and the experiment was conducted for two different cases with and without a cover. All the ten types of samples were placed on the hot plate set at 36℃, and the surface temperature and humidity were measured at three different points for 10 minutes. As a result, the case with only TPU showed the greatest temperature change while the case with 100% EVA foam showed the least temperature change. The humidity of the surface layer gradually decreased with time for 100% EVA foam. For the case with TPU materials, the moisture was transferred to the surface layer at first, thereby increasing the humidity but then dropped significantly. Meanwhile, the cases with the cover on showed similar tendencies of change in both temperature and humidity where the overall temperature and humidity delivery were slow.

• Elastomers and Composites
• /
• v.35 no.2
• /
• pp.106-114
• /
• 2000

The foam of ethylene vinyl acetate (EVA)/styrene-vinyl isoprene-styrene triblock copolymer(SVIS) blend was prepared to improve the shock-absorption and compression set characteristics at room temperature. The effects of blowing agent and blend ratio of EVA/SVIS on expansion ratio, cell structure and mechanical properties of the foam were investigated. As the SVIS content increased, the viscosity of blends was increased but the crosslinking rate was slow down, the expansion ratio was decreased. and the specific gravity was increased. At room temperature, the resilience was not affected by increasing the amount of blowing agent. The value of tan ${\delta}$ was increased by increasing the amount of SVIS. As a result, the value of compression set was decreased. This is due to the increased values of specific gravity and crosslinking density of the EVA/SVIS foam.

• Elastomers and Composites
• /
• v.35 no.4
• /
• pp.296-302
• /
• 2000

The surfaces of injection and pressure-molded sheets of poly(ethylene-covulylacetate)(EVA) foams used for shoe mid-sole were treated with low temperature plasma to improve adhesion with a water-based polyurethane adhesives. Several experimental variables were considered, such as radio frequency power, treating time, type of gas. gas flow, and distance between electrode and sample. The modificated surface by plasma treatment were characterized using contact angle meter, scanning electron microscopy(SEM), universal testing machine(UTM). Adhesion was tested by T-peel tests of treated EVA foams/polyurethane adhesive joints. The treatment in the low temperature plasma produced a noticeable decrease in contact angle. The peel strength of EVA foams treated with plasma was increased with plasma treating time, and gas flow.

• Elastomers and Composites
• /
• v.36 no.1
• /
• pp.52-60
• /
• 2001

Physical properties of foams depend on the density of foams, Physical properties of base polymers, open ceil contents, and cell structures including the size, size distribution, shape of ceil and the thickness of membrane and strut. The density of foam is affected by raw materials, concentration oi crosslinking agent and blowing agent and process parameters such as processing technique and condition. Ethylene vinyl acetate copolymer(EVA) foam is a crosslinked cellular material. The foaming characteristics and physical properties of EVA foam are affected by decomposition rate of blowing agent. In this study, the decomposition rate of blowing agent and crosslinking rate, foaming characteristics and physical properties of foams were evaluated. The slow decomposition rate of blowing agent results in low density foam, good shock absorption property and uniform cell size distribution compared to the high decomposition rate of blowing agent.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.724-727
• /
• 2002

층간차음재에 대한 관심은 증대하고 있으나 실제로 우리가 층간 차음재를 선택하는데는 많은 어려움이 있다. 여기에 소개하는 재료는 기존의 성능이나 가격을 강조하는 제품과 차별화하여 건축적 관점에서 접근이 용이할 것으로 판단되는 것이다.(중략)

• Journal of Adhesion and Interface
• /
• v.8 no.4
• /
• pp.23-31
• /
• 2007

An atmospheric plasma pre-treatment method was applied to EVA foam, Leather (Action), Rubber and Unwoven to improve its contact angle and adhesion using atmospheric plate type reactor. In order to investigate the optimum reaction condition of plasma treatment, type of reaction gas (nitrogen), rate of gas flow (30~100 mL/min), and reaction time (0~30 sec) were examined in a plate plasma reactor. The result of the surface modification with respect to the treatment procedure was characterized by using SEM. Due to a decrease of the contact angle of various materials, the greatest adhesion strength was achieved at optimum condition such as flow rate of 100 mL/min, reaction time of 10 second for an atmosphere nitrogen gas. Consequently, the atmospheric plasma treatment reduced the contact angle of the EVA foam, Leather (Action) and Rubber also resulted in the improvement of the adhesion.