• Journal of Conservation Science
• /
• v.34 no.5
• /
• pp.379-385
• /
• 2018

This study examined the condition of degraded plastic artifacts and conducted materials assessments for conservation treatment. The properties and bond characteristics of five types of adhesives(EVA, PVAc, Cyanoacrylate) were evaluated to select the adhesive most suitable for conservation treatment. The degradation of plastic artifacts caused cracks, peelings, and surface warping. According to the FT-IR analysis, the synthetic resin used in the artifact was estimated to EVA type. The properties of the adhesives were evaluated through acidity, and hardness measurements. The results showed that acidity varies with the type of adhesive, and that the hardness of PVAc was higher than those of EVA. On comparing the bond characteristics of the samples after artificial degradation, it was found that PVAc and Cyanoacrylate increased the chromaticity and hardness of the samples, while EVA was the most stable with relatively little change. Thus, EVA was confirmed to be the most suitable materials for conservation treatment of degraded plastic artifacts. In this study, as the experiment of treatment materials based on actual artifact, it is expected that it could be used a basis research for conservation treatment of plastic artifacts.

• Journal of Radiation Protection and Research
• /
• v.36 no.1
• /
• pp.8-16
• /
• 2011

We manufactured the Vac-lok that can be applied to patient of special body shape and need to special set-up position and evaluated the usefulness in the radiation therapy. The manufacture Vac-lok, It was used EVA resin and biobeadform of a diameter 1.5 mm. carried out the test of functionality, structural and analyzed the relative reproducibility of phantoms and patients. During the total period of radiation therapy, Vacuum pressure bring variety to a very small amount in the test of functionality of the manufacture Vac-lok. But It was a negligible quantity. The manufacture Vac-lok improved the relative reproducibility of phantoms than the existing Vac-lok and tolerance has a confidence less than 4% error. Also, relative reproducibility of patient increased error than phantom in the antero-posterior and lateral plan. However, the maximum set-up error was less than ${\pm}\;2.3$ mm. In conclusion, If tolerance set-up error of radiotherapy is less than ${\pm}\;3$ mm, the manufacture Vac-lok was enough possible to use and improvement of reproducibility, considering supply with the Vac-lok made to measure of special patient that produced at a low price and without delay.

• Applied Chemistry for Engineering
• /
• v.20 no.2
• /
• pp.234-240
• /
• 2009

$Mg(OH)_2$ particles were prepared by precipitation and a hydrothermal treatment to examine the effect of $MgCl_2$ concentration, alkali type and concentration, temperature, hydrothermal treatment on the formation of $Mg(OH)_2$ particles using full factorial design, as one of DOE (Design of experiment) methods. The primary particle size is similar to the secondary particle size for the samples after the hydrothermal treatment, where the average particle size of $Mg(OH)_2$ increased with increasing the concentration of $MgCl_2$ and hydrothermal temperature and decreasing alkali/Mg molar ratio. On the other hand, for the samples prepared from precipitation, the secondary particle size is larger than the primary particles due to aggregation. The difference in alkaline source is that the particles prepared from $NH_4OH$ exhibit the larger size with better dispersion than those from NaOH. Low density polyethylene and ethylene-co-vinyl acetate (LDPE-EVA) resin composed of the smaller secondary particle size of $Mg(OH)_2$ shows a higher limited oxygen index (LOI) at 50 and 55% loading, but the smaller primary particle size may result in a better grade in UL-94 tests. At the high loading of 60%, all samples with any preparation methods exhibit V-0 grade but the LOI value depends on not only primary particle size but also dispersion state.

• Korean Journal of Environmental Agriculture
• /
• v.14 no.3
• /
• pp.289-295
• /
• 1995

This study was carried out to develop a controlled-release insecticide formulation for the control of rose aphid (Macrosiphum ibarae) in rose and cotton aphid (Myzus persicae) in chrysanthemum (Dendranthema grandiflorum var. Meibung) in greenhouse. Imidacloprid[1-(6-chloro-3-pyridylmethyl)-N-nitroimidazolidin-2-ylideneamine] was chosen as a toxicant. Two synthetic polymers, low density polyethylene(LDPE) and ethylene vinyl acetate(EVA), were used as polymer matrices. The tested plastic sheet formulations were prepared by heat-aided extrusion procedures after mixing imidacloprid technical and the polymers of three different combinations, and physicochemical properties as well as efficacy of the formulations were investigated. The amounts of imidacloprid recovered and incorporated in the formulations were recorded over 90% and 80%, respectively. Release of the active ingredient from the formulations was remarkably affected by mixing rates of polymers. The active ingredient in the formulations was chemically unstable with over 10% degradation rates after 90 day storage at $50{\pm}2^{\circ}C$. The residual amounts of imidacloprid in the soil treated with the formulations were paralleled with the release pattern of the formulations. Efficacy of the formulations on rose and cotton aphid was maintained over 90% even 120days after treatment under greenhouse.