콘크리트의 강도를 결정하는 3가지 요인은 시멘트 페이스트의 강도, 골재의 강도, 골재와 시멘트페이스트 계면영역의 강도가 있다. 이 중 계면영역의 강도가 가장 취약하다. ITZ(Interfacial Transition Zone)는 10~50㎛로 형성되며, 수산화칼슘의 비율은 높아지고, CSH는 낮은 비율을 나타낸다. 높은 수산화칼슘 비율은 ITZ의 부착강도 저하의 원인이 된다. 이로인해 ITZ는 더 약한 영역이 된다. ITZ의 문제점은 경량골재를 활용할 때 더 불리한 요소로 나타난다. 계면특성의 기존연구는 계면파괴인성을 측정하고, 계면에 영향을 주는 인자들을 파악했고, 굵은 골재를 사용하지 않은 시멘트 경화체에 SEM과 XRD분석을 진행했다. 또한 EMPA-BSE장비를 활용하여 미세구조를 파악하였다. 하지만 기존의 연구에서는 미세구조와 역학적 성질 파악에 어려움이 있다. 따라서 본 연구에서는 천연골재와 경량골재 계면을 파악하기 위해 EIS측정 장비를 활용하여 전기저항을 측정하는 방식을 채택하였고, 경량골재 겉면을 고로슬래그 코팅을 통해 계면상태의 변화를 실험하였다. 실험결과, 천연골재와 경량골재의 압축강도는 밀도가 높은 천연골재 높은 강도를 나타냈고, 경량골재 표면 코팅 시 천연골재 이상의 강도를 나타냈으며, 골재 종류별 전기저항의 차이를 보였다.
Mineral description and mineralogical characterization were made for the wellsite, a barrian zeolite, which found as diagenetic alterations in the Miocene pyroclastic rocks in Gampo area. The wellsite occurs together with clinoptilolite, smectite and apatite as euhedral crystallites (0.2~0.4mm) forming interpenetraion twinning in the vesicles of altered pmice fragments. Compared to other reported wellsites, the wellsite is rather silicic (Si/(Al+Fe): 3.12-3.16) and Ca-rich. Unit cell dimensions and chemical formular determined from XRD, EMPA and TGA data are as follows:a=9.883$\AA$, b=14.204$\AA$, c=8.677$\AA$, $\beta$-124.764$^{\circ}$, (Ba0.57K0.36)(Ca1.18Na0.04)Al3.9Si12.1O32.13.9H2O.The cation composition of the Gampo wellsite, which shows an exchange reaction in the form of Ba2++Ca2+=2(K++Na-), is deviated far from the compositional range of a phillipsite-harmotome series. Due to higher abundance of divalent cations (Ca, Ba) and si in the wellsite, cimpared to those of the phillipsite and harmotome reported in other areas, the zeolite seems to be characteristic of higher water content (18.7 wt%) and higher thermal stability. XRD, chemical and thermo-chemical results of the wellsite reflects that wellsite is rather a Ba- and Ca-rich end member of a phillipsite-harmotome-wellsite series than an intermediate phase of phillipsite-harmotome series or a barrian variety of phillipste.
Synthesized monocrystalline nanodiamond (nD) particles are heat-treated at various temperatures to produce highly structured diamond crystals. The heat-treated nDs show different weight loss ratios during thermogravimetric analysis. The crystallinities of the heat-treated nDs are analyzed using Raman spectroscopy. The average particle sizes of the heat-treated nDs are measured by a dynamic light scattering (DLS) system and direct imaging observation methods. Moreover, individual dispersion behaviors of the heat-treated nD particles are investigated based on ultrasonic dispersion methods. The average particle sizes of the dispersed nDs according to the two different measurement methods show very similar size distributions. Thus, it is possible to produce highly crystallized nD powder particles by a heat-treatment process, and the nD particles are relatively easy to disperse individually without any dispersant. The heat-treated nDs can lead to potential applications such as in nanocomposites, quantum dots, and biomedical materials.
This paper presents a systematic design and training procedure for the feed-forward back-propagation neural network (NN) modeling of both forward and inverse behavior of a rotary magnetorheological (MR) damper based on experimental data. For the forward damper model, with damper force as output, an optimization procedure demonstrates accurate training of the NN architecture with only current and velocity as input states. For the inverse damper model, with current as output, the absolute value of velocity and force are used as input states to avoid negative current spikes when tracking a desired damper force. The forward and inverse damper models are trained and validated experimentally, combining a limited number of harmonic displacement records, and constant and half-sinusoidal current records. In general the validation shows accurate results for both forward and inverse damper models, where the observed modeling errors for the inverse model can be related to knocking effects in the measured force due to the bearing plays between hydraulic piston and MR damper rod. Finally, the validated models are used to emulate pure viscous damping. Comparison of numerical and experimental results demonstrates good agreement in the post-yield region of the MR damper, while the main error of the inverse NN occurs in the pre-yield region where the inverse NN overestimates the current to track the desired viscous force.
Journal of Advanced Marine Engineering and Technology
/
제18권2호
/
pp.33-40
/
1994
알루미늄 코팅막은 부식환경으로부터 강판을 보호하는 데에 자주 사용된다. 그러나 이 코팅막은 때때로 사용조건에 따라 제한을 받는다. 아무리 강판상에 치밀한 양질막을 코팅시켰다 할지라도, 사용중 이 피막이 손상을 받아서 강판이 노출되는 경우는 강판과의 갈바닉(Galvanic)작용으로 급격한 부식을 일으킨다. 본 연구는 내식성 개선을 목적으로 해서, 고밀착성의 코팅막을 제공하는 비평형프라즈마 프로세스인 이온프레이팅법에 의해 냉간압연강판상에 Al-Mg합금 코팅막을 제작했다. 제작된 막들은 우선, EMPA측정에 의해 원소조성분석을 한 후, 상구조분석 및 표.단면의 몰포로지(Molphology)를 X선 회절 및 주사형 전자현미경(SEM)에 의해 관찰했다. 또한, 이들막은 탈기시킨 3%NaCl용액중 양극분극 측정을 통해서 내식특성에 대한 평가를 행했다. 이들의 결과에 의하면, 알루미늄과 마그네슘의 조성비에 따라 주상, 미결정 및 아몰포스(Amorphous)조직을 보이는 금속간화합물이나 고용체의 Al-Mg박막이 나타났다. 이들 Al-Mg합금 코팅막은 강판과의 갈바닉 부식작용에 대한 방지 및 부동태 피막의 형성을 촉진하는 등의 좋은 내식성을 나타냈다.
The purpose of this research is to provide accurate information of household washers and detergents for consumers, so that help the producers who make washing machine and detergent to get basic material and also help consumers to choose washing machine. Experiment was proceed with two type of washers to compare energy consumption, washing performance, rinsing effectiveness further, damage caused by entanglement of laundry and fabric was assessed. Detergent P and T were used to compare the performance related to differences of ingredients of detergent. Soiled fabrics of EMPA 108 set were used to evaluate performance of washing by different types of contamination. A summary of experimental results are : First, for the consumption of water, drum-type washer consumed 53% less than pulsator-type washer. On the other hand, the washing time was almost similar for both these machines, but pulsator-type washer showed shorter progress, implying that power saving was more efficient in this case. Second, the drum-type washer showed better performance for contamination with all types of detergent, but the pulsator-type washer showed better rinsing performance. Third, the drum-type washer performed less data of tangle level and fabric damage. Fourth, detergent "P" exhibited better washing performance than did detergent "T", regardless of the type of soil. And with no limit of detergent variety, water-soluble protein soil showed high removal rate, liposoluble soil especially pigment was hardly removed.
The main purpose of this study is to investigate the effects of process parameter on alpha-case formation of Ti and TiAl castings. The previous studies showed that the molten titanium is excessively reactive to the refractory oxide mold, resulting in alpha-caes of the titanium castings regardless of composition of titanium alloys. However, the behavior of the alpha-case formation of TiAl alloy is not consistent with conventional titanium alloy. In order to investigate the alpha-case formation of Ti and TiAl castings with process parameter, especially the associated factors of investment mold such as mold material, binder and mold preheating temperature. An attempt has been made to characterize the alpha-case of titanium casting by using optical microscope, EDS, XRD, EMPA and hardness profiles. The formation of the alpha-case on the surface of pure titanium during investment casting was rather by that of solid solution with metallic element from mold material. The required mold strength was obtained with $CaZrO_3$ because of the possibility of using water soluble binder. However, the separation phenomenon between facing and back-up mold materials should be considered. The interfacial reaction of TiAl alloy showed different behavior from that of pure titanium and $Al_2O_3$ was best mold materials. The effect of binder as well as mold material on the formation of alpha-case was significant.
This study manufactured a CIG-based composite coating layer utilizing a new warm spray process, and a mixed powder of Cu-20at.%Ga and Cu-20at.%In. In order to obtain the mixed powder with desired composition, the Cu-20at.%Ga and Cu-20at.%In powders were mixed with a 7:1 ratio. The mixed powder had an average particle size of $35.4{\mu}m$. Through the utilization of a warm spray process, a CIG-based composite coating layer of $180{\mu}m$ thickness could be manufactured on a pure Al matrix. To analyze the microstructure and phase, the warm sprayed coating layer underwent XRD, SEM/EDS and EMPA analyses. In addition, to improve the physical properties of the coating layer, an annealing heat treatment was conducted at temperatures of $200^{\circ}C$, $400^{\circ}C$ and $600^{\circ}C$ for 1 hour each. The microstructure analysis identified ${\alpha}$-Cu, $Cu_4In$ and $Cu_3Ga$ phases in the early mixed powder, while $Cu_4In$ disappeared, and additional $Cu_9In_4$ and $Cu_9Ga_4$ phases were identified in the warm sprayed coating layer. Porosity after annealing heat treatment reduced from 0.75% (warm sprayed coating layer) to 0.6% (after $600^{\circ}C/1hr$. heat treatment), and hardness reduced from 288 Hv to 190 Hv. No significant phase changes were found after annealing heat treatment.
The effects of nonionic surfactants on detergency and water wetting/retention properties of soiled cotton cloths were reported. Two different soiled cloths were used. soiled cotton cloth 1 was made in the lab. with carbon black, tripalmitin, n-dodecane & palmitic acid on Korea Apparel Testing & Research Institute(KATRI) cotton testcloth and soiled cotton cloth 2(EMPA 101) was purchased from Testfabrics, Inc., USA. The following nonionic surfactants; l.e., Span 20, Tween 20, 40, 60, 80, 21, 61, 81, 65, & 85, were used in the study. The water retention ratio(W/H) values of soiled cotton cloths were decreased, whereas the water contact angle values of soiled cloth were not changed markedly compared with those of unsoiled testcloths. The wetting and water retention of soiled cotton cloth 1 was improved with addition of nonoinic surfactants. The surfactants which have more hydrophilic characterictics or unsaturated hydrophobe tails were effective in improving wetting and water retention properties of soiled cotton cloth 1. The water contact angle values of soiled cotton cloths were extremely low with Span 20, presumably due to the high adsorption density or the surfactant. The detergency of soiled cloths were low in Span 20 and high in Tween 20, 40, 60 & 80 0.1g/dl surfactant solutions. Nonionic surfactants having higher ethylene oxide contents resulted in better detergency. In the range studied, the wetting and water retention of soiled cotton cloths did not show any particular relation to the detergency, whereas the surfactant characteristics, especially HLB values, influenced the detergency of soiled cotton cloths.
The purpose of this research is to improve sustainable clothes care by comparing household washer's standard course and quick course. Detergency at each course was classified by laundry weight, detergent concentration, and soils. Also, fabric damage from each course was compared. Washing experiments were carried out using two types of washing machines and three types of detergents. Using the standard soiled fabrics of EMPA 108 set, detergency was compared by laundry weight, soil, and detergent concentration. Additionally, fabric damage was evaluated using the mechanical action of MA-40. The results of the research were as follows. First, a standard course, having more working time exhibited better detergency than a quick course. However, the detergency deviation under 6kg laundry weight was as low as 9.0%. Second, detergency by the type of soil was more effective in standard course than in a quick course, but hydrophilic protein soils had a small detergency deviation at 7.6%. Moreover, hydrophobic oil, complex, and particulate soils had a higher deviation at 19.7% Third, fabric damage was in proportion to operating time. Fourth, a quick course showed approximately 80% detergency regardless of the type of detergent. in the case of using 50% of the recommended allowance by the detergent manufacturer. In conclusion, reducing the operating washing time and detergent concentration is in accordance with increasing sustainability, in the case of washing with lightly soiled fabrics under 6kg of laundry weight.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.