• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.2
• /
• pp.214-222
• /
• 2008

The equivalent circuit for the RLH-TL is proposed considering radiation effects due to the inclusion of a series capacitor and shunt inductor in a unit cell for the right/left-handed transmission line(RLH-TL). The design equations to realize a specific phase shift at a given frequency is also provided. The S-parameters for unit cells with N=1, 3, 5, and 10 are analyzed in various aspects based on the EM and circuit simulations especially for the purpose of controlling radiation along RLH-TL's. A modification formula for the radiation rate per unit cell is also proposed for good agreement between the EM and circuit simulation results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.24 no.11
• /
• pp.1081-1090
• /
• 2013

In this paper, a C-band 10 W power amplifier with internally matched input and output matching circuit is designed and fabricated. The used power transistor for the power amplifier is GaAs pHEMT bare-chip. The wire bonding analysis considering the size of the capacitor and the position of transistor pad improves the accurate design. The matching circuit design with the package effect using EM simulation is performed. To reduce the unsymmetry of IMD3 in 2-tone measurement due to the memory effect, the bias circuit minimizing the memory effect is proposed and employed. The measured $P_{1dB}$, power gain, and power added efficiency are 39.8~40.4 dBm, 9.7~10.4 dB, and 33.4~38.0 %, respectively. Adopting the proposed bias circuit, the difference between the upper and lower IMD3 is less than 0.76 dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.27 no.8
• /
• pp.709-716
• /
• 2016

In this paper, A duplexer module with temperature-insensitive electrical characteristics was proposed for remote wireless communication system. Duplexer modules are required to have performances of low insertion loss, high isolation between transmitted band and received band, harmonic suppression as well as high power durability in the system for transmitting guided information to missile flying a free space on the ground. The proposed duplexer module are consist of transmission bandpass filter and receiving bandpass filter which are connected to common antenna port, planar coupler for output power monitoring and low pass filter for harmonic attenuation of power amplifier and coaxial cavity resonator. The material and dimensions of the resonator are determined for minimum frequency shift by temperature variation using 3D EM simulation. The measured results of the prototype showed a good agreement with the simulation results, and it should be well applied not only for guided weapon systems but also for any other communication systems such as remote radio head.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.6
• /
• pp.608-618
• /
• 2004

In this paper, modifying the diode star double balanced mixer of Maas, a novel resistive 60 GHz pHEMT MMIC star mixer is suggested. Due to star configuration, troublesome IF balun for ring configuration FET mixer is not necessary. In addition, the sysematic design method of dual balun through EM simulation is suggested rather than the design by inspection as Maas. The mixer circuit is fabricated as MMIC on CPW base using 0.1 um GaAs pHEMT Library of MINT in Dongguk University. The size is 1.5 ${\times}$ 1.5 $\textrm{mm}^2$ and its performance is adjustable by DC supply. It can be operated as both up and down converters and it shows the conversion loss of about 13∼18 ㏈ over the full V-band frequencies.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.2
• /
• pp.162-172
• /
• 2011

In this paper, a design and fabrication of 4 W power amplifier for the WiMAX frequency band(2.3~2.7 GHz) are presented. The adopted active device is a commercially available GaN HEMT chip of Triquint Company, which is recently released. The optimum input and output impedances are extracted for power amplifier design using a specially self-designed tuning jig. Using the adopted impedances value, class-F power amplifier was designed based on EM simulation. For integration and matching in the small package module, spiral inductors and interdigital capacitors are used. The fabricated power amplifier with $4.4{\times}4.4\;mm^2$ shows the efficiency above 50 % and harmonic suppression above 40 dBc for second(2nd) and third(3rd) harmonic at the output power of 36 dBm.

• Transactions on Electrical and Electronic Materials
• /
• v.10 no.5
• /
• pp.173-176
• /
• 2009

In the stator windings of a 6.6 kV rotating machine, internal discharges, slot discharges, and surface discharges are mainly caused by internal voids and insulation degradation. If a partial discharge(PD) occurs in an inner-part of the stator windings, it will cause electromagnetic pulses with wide frequency ranges. Discharge sparks and electromagnetic pulses generated from a discharge source, can be detected using various RF resonators like an EM sensor. In order to detect these types of electromagnetic sources, a planar patch sensor was designed and fabricated using a CST-MWS simulation, and PD signals from an artificially defected stator winding were also measured by the sensor proposed in this study. Furthermore, an HFCT was used as a reference sensor and compared with the proposed new planar patch sensor. In the results of the experiment, the planar patch sensor showed a similar performance to the HFCT sensor.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.5
• /
• pp.481-485
• /
• 2008

In stator windings of 6.6 kV rotating machine, corona discharge, surface discharge and internal discharge are caused mainly by internal voids and insulation degradation. Also, if partial discharge occurs in inner-part of stator windings, it will be happened electromagnetic pulses at wide frequency range. In case of discharge spark, electromagnetic pulse generated from discharge source, and we can detect it by using various RF resonators as an EM sensor. In order to detect these kind of electromagnetic sources, we have designed and fabricated planar patch sensor using CST MWS simulation, and also PD signals from artificial defected cable were measured by our proposed sensor. Furthermore, HFCT was used as a reference sensor and compared with our proposed new planar patch sensor.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2003.11a
• /
• pp.423-427
• /
• 2003

In this paper, LTCC stacked patch antenna with a radial CPW fed slot and grounded-shorting vertical-via wall for 19GHz band wireless LAN is presented. Suggested antenna employed a patch and grounded-shorting vertical-via wall for radiation element, consist of feeding structure which a radial open feature at the end of the CPW feed line. The optimal design parameters of the antenna using by EM simulation program. We can see that enough to bandwidth 560MHz for 19GHz band WLAN antenna specification by the optimized antenna.

• Journal of electromagnetic engineering and science
• /
• v.6 no.4
• /
• pp.217-221
• /
• 2006

Multipactor-free S-band duplexer based on inter-digital cavity type filter is proposed and demonstrated by in-house mulitpactor test facility for satellite RF components. Multipactor sensitivity of designed duplexer is analyzed by checking it out the maximum field accumulated region inside duplexer and calculating the electric field intensities at each resonator using 3D EM simulation in order to restrict the minimum gap distance as 2.5 mm which handles 43.13 dBm RF input power. Multipactor threshold was finally detected at 44 dBm in experiment for pulse mode test. The developed multipactor test method is cost effective, simple structure and gives a good agreement compared with the previous high cost MP test methodologies.

• Journal of electromagnetic engineering and science
• /
• v.14 no.4
• /
• pp.415-418
• /
• 2014

This paper presents an equivalent circuit model for a dumbbell-shaped defected ground structure (DGS) in a microstrip line. The effects of equivalent circuit elements of a dumbbell-shaped DGS and their magnetic coupling to the host transmission line are modeled as a simple lumped-element circuit. In addition, simple approximate expressions to determine the main circuit parameters for this model are presented. The transfer characteristic calculated by the proposed circuit model is compared with the results of EM simulation and measurement.